Used Faymonville Multimax Satteltieflader (1+3) - Hydr. Gelenkt for sale (102,541)

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) Bsdpfx Afetx Nwnsmjlk LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: new, overall weight: 80,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, More vehicles available. Excerpt from the equipment list below. Full equipment details on request. GOOSENECK: * Gooseneck in SNT design, optimized for loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * Suitable for tractors: 4 x 2, 6 x 2, and 6 x 4 * Detachable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX at the front connection rail with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic unit for controlling all hydraulic functions except hydraulic winches Bledpsxarmaofx Afmsk * Gooseneck outer rail with mounting holes for screwable lashing rings. First hole approx. 200 mm from front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings at rear part of gooseneck (LC 10,000 daN) * On the gooseneck: 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized finish * On the gooseneck: 1 plug-in aluminum rear wall, approx. 400 mm high, anodized finish * Approx. 40 mm hardwood floor covering on gooseneck, checker plate covering over kingpin * 3.5-inch kingpin * Gooseneck guide plate for the fifth wheel, approx. 500 mm wide * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) * 2 pairs of lashing rings with retention spring hanging on the outer rails of the gooseneck (LC 5,000 daN) LOADING PLATFORM: * Extendable loading platform, length approx. 8,800 mm with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical lock bolt and reinforced locking positions; supply lines routed securely inside the extendable rails, automatically adapting to the current platform length * BPW axles and suspension; 1st axle steerable, all others force-steered via hydro-mechanics * 1st axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lifting/lowering valve * 235/75 R 17.5 3PMSF twin tires – brand at our discretion * Mechanical landing gear with 2-speed gearbox and crank. JOST Modul B – static test load 50,000 kg * Full-length hardwood floor, interrupted between axles, approx. 50 mm thick (increases slip resistance). – Long slots for removable and repositionable bridging elements * At the front of the platform – 1 movable intermediate table, approx. 300 mm wide, for the large-cross-section sliding tube, with checker plate covering. – Front and rear with long slots for removable and repositionable bridging elements * 1 pair of lashing rings on front cross member (LC 10,000 daN) * 7 pairs of flush-mounted, fold-out lashing rings in the outer frame of the platform (LC 10,000 daN) * Extendable (galvanized) widened sections, approx. 230 mm per side (without wooden planks) * 1 pair of mechanical rear supports * Rear steering operable from front and rear via cable remote control, with single-track control of axles, without installation on the tractor * TPMS tire pressure monitoring sensors fitted to all wheels * Deck locking with conically welded locking profiles every 500 mm * Lock monitoring left and right on the trailer * Mechanical lock for intermediate table (approx. 300 mm wide) to secure the table when extended * 5 pairs of threaded blocks mounted on the extendable rail for the installation of M20 screw-in rings (LC 5,000 daN) BRAKING SYSTEM

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) Bodpfxorgzv Ne Afmjlk * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: new, maximum load weight: 36,410 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Extract from the equipment. Full equipment details available on request. GOOSENECK: * Gooseneck in SNT design for optimized loading platform length, length approx. 3,700 mm, rear with taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Steel front wall, removable, approx. 400 mm high * ASPÖCK-UNIBOX * 3 kW electro-hydraulic power unit for hydraulic functions, excluding hydraulic winches * Approx. 40 mm thick hardwood decking above the gooseneck * 2-inch kingpin * Gooseneck guide plate for the fifth-wheel plate, approx. 500 mm wide * Bracket at the rear of the gooseneck for ALU loading ramps * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 4 wheel chocks with holders in front of the front wall * 1 pair of stake pockets recessed on the gooseneck for plug-in stakes approx. 100 x 50 mm (located on the inside of the chassis rail) Bljdpfx Aey Auh Isfmek EQUIPMENT: * Loading platform length approx. 8,800 mm, extendable version approx. 4,100 mm, with rear taper approx. 500 mm x 10° * A recess in the loading platform, extending into the tapered section to accommodate the excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * Pneumatic locking with conical locking bolts and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adapt to the selected loading platform length * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steered * 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: each 12,000 kg with air suspension and raise/lower valve * 235/75 R 17.5 3PMSF twin tires. Manufacturer at our discretion * Mechanical landing legs with 2-speed gearbox and crank. JOST Module B – static test load = approx. 50,000 kg * Throughout the loading platform and between the axles, interrupted approx. 50 mm thick hardwood decking (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the telescopic tube with large cross-section. Intermediate table with offset loading platform and extendable mounting rails for aluminum bridging elements * Platform locking with conically welded locking profiles every approx. 250 mm. Includes pre-tensioning plate * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards (LC 10,000 daN) * 1 pair of fixed wheel recesses in front of the axles, open up to the gooseneck cross member, approx. 700 x 410 mm (W x D) * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom (in case vehicle is equipped with extendable widenings) * 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the platform between 1st and 2nd axle * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axle, which can also be used as widening planks (if vehicle is equipped with extendable widenings) * Lockable aluminum elements installed on the extension tubes of the widenings * 1 pair of mechanical rear supports * 1st axle with traction aid * Sandblasting painted...

Condition: used, maximum load weight: 31,100 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 03/2013, Year of construction: 2013, Equipment: ABS, * Faymonville F-S43-1ABA low-loader * First registered: 03-2013 * Hydraulic lift * Hydraulically adjustable double-folding gooseneck * Includes cable winch with remote control Bjdpfx Ajzq N N Hofmelk * 3rd axle with trailing linkage * SAF axles * Air suspension * Drum brakes * Payload: 10,900 kg * Net weight: 31,100 kg * Gross vehicle weight: 42,000 kg * Tires 235 / 75 R 17.5 * More pictures and videos available via WhatsApp * Specifications subject to change without notice; sale subject to prior sale.

Condition: used, Year of construction: 2014, Please contact Theo Lelie for more information Blodpfx Afjxtqkwsmjk

Condition: used, overall weight: 45,000 kg, axle configuration: 3 axles, first registration: 09/2017, * SAF axles * Wheel recesses Bedpfx Afewta Alomjlk * Hydraulically adjustable loading ramps (width) * Air suspension * Extendable * Tare weight: 11,020 kg -----Internal vehicle number: 11010----Errors and prior sale excepted. WhatsApp support available! If you have any questions about the vehicle or would like more information, please feel free to contact us conveniently via WhatsApp. WhatsApp – German, English – WhatsApp – German, English, Arabic.

Condition: new, maximum load weight: 38,953 kg, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, MAX100-N-3B-9.30-U Technical Data Speed: 80 km/h Total weight: 49,500 kg Saddle load: 18,000 kg Axle load: 31,500 kg Unladen weight (+/- 3%): 10,547 kg Payload approx.: 38,953 kg Gooseneck length: 3850 mm Saddle height loaded: 1200 mm Loading platform length: 9300 mm Extendable by: 0 mm Axle distance: 1360 mm Rear deflection radius: 2300 mm Loading height at max. load: 860 mm Overall width: 2540 mm Suspension travel: -55 / +145 mm Technical Description Gooseneck: Gooseneck with beveled front corners at 45° and a rear bevel of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, 30 mm thick. Bedpfx Afjg Sk Tromelk Loading platform: Loading platform after the gooseneck, hydraulically raisable and lowerable, length approx. 2,800 mm, with a rear bevel of approx. 1,000 mm x 8°. 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN). 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 1 pair of lashing rings that can be folded inwards on the central beam at the front (LC 10,000 daN). Cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN). Hardwood flooring approx. 48 mm thick, with non-slip steel plate flooring over the axles. Ramps: Two-piece steel ramps, one pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood flooring. Ramp with hydraulically raising and folding ramp sections, hydraulic lifting mechanism and hydraulically adjustable. Maximum load per pair: 40,000 kg Kingpin: JOST kingpins (mechanical) with a 2-speed gearbox for a 24t lifting capacity (50t test load). Tires: Tires 235/75 R 17.5, as selected by the manufacturer. Axle: SAF axles, air-suspended, with drum brakes, with raising/lowering function. The last axle is steered with an electro-magnetic reverse steering lock, which can be activated via reverse gear or manually. Axle tool. Braking system: Braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel structure: Steel structure made of high-strength fine-grained steels. Steel qualities: S355J2+N / S355MC (yield strength 355 MPa) S690QL / S700MC (yield strength 690 MPa) Painting: First-class and durable corrosion protection of the standard bead-blasted welded frame is guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) topcoat in a single color in RAL colors of your choice. Rear part metallized and painted in RAL 9010 (pure white). Metallic paint is not possible. Electrical system: Electrical system according to EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the connection bar at the front with 24N, 24S & 15-pin sockets. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Included accessories 2" kingpin One galvanized steel front wall, approx. 400 mm high. Yellow-red air couplings on the galvanized connection bar at the front. 4 pieces of wheel chocks with holders on the front wall. (± 5 kg) Cable for supplying the electro-hydraulic unit and/or the electric winch (35mm², 3.5 m long, max. 250A) between the semi-trailer and the tractor unit with plug connection (ANDERSON-ANDERSON) Galvanized folding supports under the bevel of the loading platform. One bracket for a rotating beacon on the rear of the semi-trailer. Operating valves for the ramps mounted on the right side of the semi-trailer. (± 4 kg) Yellow reflector tape according to EU regulations on the side and r

Condition: new, maximum load weight: 36,500 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website: -ge.de. The following is an excerpt from the equipment list. Complete equipment list available upon request. GOOSENECK: * Gooseneck in SNT design to optimize the loading area length, approximately 3,700 mm long, with a rear slope of approximately 1,000 mm x 6° * For semi-trailer tractors: 4 x 2 and 6 x 2 * ASPÖCK-UNIBOX * Grated steel flooring with 5 mm sheet metal reinforcement on the gooseneck and the rear slope * 2-inch kingpin * Guide plate on the gooseneck for the fifth wheel, approximately 500 mm wide * Round NATO socket on the connection bar at the front (Maeler & Kaege VG 96 917) * 1 pair of plug-in aluminum side panels on the gooseneck, approximately 400 mm high, with an anodized finish * 1 LED work light each on the left and right sides at the top of the front wall, operated via an on/off switch (operating the work lights from the semi-trailer tractor is not possible in this case) LOADING AREA: * Loading area, approximately 9,600 mm long, with a rear slope of approximately 900 mm x 6° * Loading area behind the gooseneck can be hydraulically raised and lowered, approximately 3,000 mm long, with a load capacity of up to approximately 9,000 kg * Continuous grated steel flooring with approximately 5 mm sheet metal backing as additional reinforcement on the lifting platform and the loading area, designed for point loads TIRES: * 235/75 R 17.5 3PMSF, twin tires. Brand of our choice * TPMS tire pressure monitoring system according to ECE R 141 AXLES: * BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle with trailing steering * 3rd axle with electro-magnetic reverse locking function, activated via reverse gear and manually * 1st axle with starting assist * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve HYDRAULIC LOADING RAMPS: * 1 pair of two-piece AXS steel ramps with grated steel flooring, approximately 4,920 mm long and approximately 900 mm wide * Hydraulically folding ramp tips * Ramps can be individually hydraulically moved outwards by approximately 235 mm and inwards by approximately 365 mm * Flashing lights on the outer sides of the ramp tips, with a switch next to the ramp operation controls * Ramp locking in the driving position by means of a quick-release mechanism * Painted sandblasted coating on the outer frame of the ramp and on the ramp tip Bodoy Auhhepfx Afmolk * Mechanical supports in drop-pipe design on the sides of the ramps for support when connecting to loading docks * Operating valves for the hydraulic ramps on the right side of the vehicle BRAKE SYSTEM: * WABCO EBS-E brake system according to EU regulations SURFACE TREATMENT: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection PAINTING: * Trailer: Carmine Red (RAL 3002) * Rims: Silver Gray * Side panels: Aluminum, natural finish * Wheel hubs: According to axle manufacturer * Lamp housing: Pure White (RAL 9010) EQUIPMENT: * Steel front wall, plug-in, approximately 1,600 mm high, including a connection bar for supply lines to the semi-trailer tractor, mounted approximately 1,000 mm from the bottom edge of the outer frame profile * Attachment option for lashing chains on the inside left and right sides of the front wall, including aluminum trays underneath on the left and right sides for storing chains or tension straps * Appro

Condition: used, maximum load weight: 35,600 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 07/2025, next inspection (TÜV): 07/2027, Equipment: ABS, Excerpt from Equipment List: Gooseneck: Gooseneck in SNT design to optimize the length of the loading area, approximately 3,700 mm long. The rear of the gooseneck has a bevel of approximately 1,000 mm x 6°. Technical fifth-wheel load: 18,000 kg. Suitable for SZM (special heavy-duty vehicles): 4 x 2 and 6 x 2 axle configurations. Loading Platform: Telescoping loading platform, approximately 9,600 mm long, with a rear bevel of approximately 900 mm x 6°. The loading platform can be hydraulically raised and lowered after the gooseneck, with a length of approximately 3,000 mm. Load capacity up to approximately 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS. A pair of two-part AXS steel ramps with a length of approximately 4,920 mm and a width of approximately 900 mm. Open grid flooring. Hydraulically folding ramp ends. The ramps can be individually moved outwards approximately 235 mm and inwards approximately 365 mm hydraulically. Maximum load and approach angle according to technical data sheet: C470319. Maximum angle of inclination with the loading platform lowered: approximately 9°. Axles and Suspension: BPW axles and suspension. The 1st and 2nd axles are fixed, and the 3rd axle is steered. Technical axle load: 12,000 kg. Electro-magnetic reverse lock, activated via reverse gear and manually. Air suspension with lifting and lowering valve. Axle tool. Braking System: Braking system from WABCO EBS-E, in accordance with EU regulations. No connection cable to the tractor unit. Bjdozkx Hbjpfx Afmslk Tires: 235/75 R 17.5 3PMSF, twin tires. Manufacturer of our choice. Load index 143/141J (144/144F). Paint Finish: 6-coat finish: Complete steel construction blasted with shot after welding. 1 coat of zinc-based primer, 1 coat of adhesive primer. Topcoat with 2 coats of 2-component paint (acrylic), in a single color: RAL 3002 carmine red, followed by sealing of cavities with special wax. Rims in silver. Multi-color and special paint finishes available at an extra charge. Included Accessories: - ASPÖCK-UNIBOX on the connection strip at the front, with 24N, 24S & 15-pin sockets. - 24N connection according to ISO-1185 - 24S connection according to ISO-3731 - 15-pin connection according to ISO-12098 - 3 kW electric-hydraulic unit for controlling the hydraulic operations, with the exception of hydraulic winches. - Parking position on the gooseneck for warning signs when not in use. - Outboard supports on the gooseneck with mounting holes for screw-on lashing rings. - The first hole is approximately 200 mm from the front, then approximately every 400 mm. - One mounting hole in the rear upper area of the outboard supports of the gooseneck for a screw-on lashing ring. - 1 pair of screw-in lashing rings included (LC 10,000 daN). - 3 pairs of recessed lashing rings inside the outboard support of the gooseneck (LC 5,000 daN). - 3 pairs of recessed lashing rings in the middle of the gooseneck (LC 5,000 daN). - 1 pair of recessed lashing rings at the rear in the middle of the gooseneck (LC 5,000 daN). - Grid flooring with approximately 5 mm sheet metal reinforcement on the gooseneck and rear bevel. - 2-inch Kingpin - Guide plate on the gooseneck for the fifth-wheel plate, approximately 500 mm wide. - Mechanical fifth-wheel supports with 2-speed gearbox and crank. - JOST Module B - static test load = 50,000 kg - Continuous grid flooring with 5 mm sheet metal as additional reinforcement, designed for point load: - Locking of the loading platform with conically welded locking profile

Condition: new, maximum load weight: 36,500 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt from the equipment features. Full equipment list available upon request. - Gooseneck, approx. 4,100 mm in length with central beam - Load platform with double-extendable design, length approx. 9,400 mm - BPW axles and suspension - All axles hydromechanically forced-steered - Technical axle load: 12,000 kg Blodpfx Afjwvzg Romek - Air suspension with raise and lower valve - Twin tires 235/75 R 17.5 3PMSF - WABCO braking system, EBS-E - 3 kW electro-hydraulic unit for hydraulic operations. Without installation of supply connections on the tractor unit - 4 pairs of stake pockets integrated in the outer frame of the gooseneck, suitable for insertable stakes approx. 100 x 50 mm - 2-inch king pin - 8 pairs of stake pockets integrated in the outer frame of the loading area, suitable for insertable stakes approx. 100 x 50 mm - 1 lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the loading platform on the left-hand side in direction of travel - Remote steering control from front and rear using cable remote with push buttons, with axle tracking control, without installation in the tractor unit - 2 axle load gauges mounted on the left side - Steel front wall, approx. 1,600 mm high - 3 transverse rows of stake pockets mounted in the floor of the loading area for insertable stakes approx. 100 x 50 mm - 1 transverse row of stake pockets mounted in the floor of the gooseneck for insertable stakes approx. 100 x 50 mm - 1 additional lockable INOX toolbox, mounted under the loading area - WADER container pockets in the loading area for transporting: 2x 20' containers or 1x 40' container - Central automatic lubrication system with 2 pumps, BEKAMAX brand - Complete HRM Metalization (High Resistance Metallisation)

Condition: new, maximum load weight: 48,300 kg, overall weight: 71,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available for immediate and short-term delivery, on our website. Extract from the equipment features. Full specification available on request. GOOSENECK: * Gooseneck with integrated 1-axle running gear (pendulum axle) in detachable design * Gooseneck hydraulically liftable and lowerable, including hydraulic coupling connected with the hydraulic axle compensation of the first axles * Length: approx. 5,200 mm, with a front taper of approx. 60° * Saddle load according to data sheet: W25-DSR2700-12/22.7 * For tractor units: 6 x 4 or 8 x 4 * Front bulkhead made of steel, detachable, approx. 400 mm high, with chamfered design * 1 pair of mechanical supports at the front of the gooseneck * ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets * 1 spare wheel holder inside on the front bulkhead of the gooseneck with lifting arm * 2 pairs of recessed lashing rings on the gooseneck (LC 2,500 daN) * 2 pairs of recessed lashing rings in the outer frame of the front chassis, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings at the transition between chassis and loading platform (LC 10,600 daN) * On the gooseneck, 1 pair of plug-in side aluminium drop sides, approx. 400 mm high, anodized finish * On the gooseneck, 1 plug-in aluminium tailboard, approx. 400 mm high, anodized finish * 3.5-inch king pin * TPMS tire pressure monitoring system compliant with ECE R 141 Blodpfxsyhkqnj Afmek * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 1 INOX toolbox with 1 lid, mounted on top of the gooseneck on the right in the direction of travel near the aluminium drop side, approx. 1,350 x 400 x 400 mm (L x W x H) LOADING AREA: * Lowbed with external main beams, designed as a telescopic loading platform in low-profile layout with front extension including a fixed approx. 50 mm hardwood floor * Length x width approx. 8,000 mm x 2,740 mm * Mechanical pin-lug coupling from the lowbed to the chassis to exchange the platform or install extension beams * 1 locking position every approx. 500 mm in the extension section * 4 pairs of recessed lashing rings arranged lengthwise on the loading area, distributed along the outer frame/main beam (LC 10,000 daN) * 1 lashing ring per side on the outside of the rear crossmember (LC 10,000 daN) * Foldable widening sections, approx. 230 mm per side (WITHOUT timber planks) * Detachable widening planks, steel-edged * Preparation for installation of bolt-on container positioning devices for 1x 20' or 1x 40' container on the main beams. Container locks not included * 6 pairs of threaded blocks between the lashing rings under the upper flange on the main beam for mounting screw-type M24 rings (LC 8,000 daN) * 2 pairs of M24 screw rings (LC 8,000 daN) included REAR RUNNING GEAR: * Rear running gear with closed external frame, checker plate decking and continuous prism-shaped excavator recess, approx. 1,450 x 900 x 505 mm, open at rear * Pendulum axle, all axles hydro-mechanically forced steered * Hose burst valve on the axle compensation cylinders with automatic reset function * Hydraulic cylinders with shut-off cocks and pre-insertion facility for securing in raised position * Final paint on axles in 2 coats of 2-pack paint, solid colour DB 7350 Novagrau * Technical axle load: 12,000 kg each * Hydraulic axle compensation * 245/70 R 17.5 3PMSF. Brand at our discretion * Remote steering from front and rear via cable-control, with axle alig

Condition: new, maximum load weight: 36,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You will find our complete vehicle inventory, including immediately and soon-to-be available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. - Gooseneck in SNT design to optimize load platform length, approx. 3,700 mm long, with a rear taper approx. 1,000 mm x 6° - For tractors: 4 x 2 and 6 x 2 - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets - 3 kW electro-hydraulic power pack for hydraulic operations (excluding hydraulic winches). Without supply line installation on the tractor unit - Outer beams of the gooseneck with mounting holes for boltable lashing rings. First hole approx. 200 mm from the front, subsequent holes approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) - One mounting hole at the rear upper part of the gooseneck’s outer beams for a boltable lashing ring - 1 pair of screw-in lashing rings included (LC 10,000 daN) - 3 pairs of recessed lashing rings inside the gooseneck’s outer beams (LC 5,000 daN) - 3 pairs of recessed lashing rings in the center of the gooseneck (LC 5,000 daN) - 1 pair of recessed lashing rings at the rear center of the gooseneck (LC 5,000 daN) - Grating covering on the gooseneck and rear taper with 5 mm steel reinforcement - 2" kingpin - Round NATO socket at the front connection panel (Maeler & Kaege VG 96 917) - Spiral cable for powering the electro-hydraulic unit and/or electric winch (approx. 35 mm², approx. 3.5 m long) between trailer and tractor unit, with plug (NATO-NATO) Bljdpfx Aoyhkquefmek - 1 pair of detachable aluminum side boards on the gooseneck, approx. 400 mm high, anodized finish CARGO AREA: - Cargo area, approx. 9,600 mm long, with rear taper approx. 900 mm x 6° - Cargo area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, load capacity up to approx. 9,000 kg - TPMS (Tire Pressure Monitoring System) according to ECE R 141 - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle with trailing steering. 3rd axle with electromagnetic reverse lock via reverse gear and manual activation - Technical axle load: 12,000 kg each - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF twin tires. Brand of our choice, load index 143/141J (144/144F) - Mechanical landing legs with 2-speed gearbox and crank - Continuous grating flooring with approx. 5 mm steel plating for additional reinforcement, designed for point loads: on the lift bed and cargo area - Painted sand coating on the gooseneck cover plates as well as transition areas between neck and lift bed, lift bed and cargo area, and cargo area and ramps - 1 spare wheel mounting bracket under the cargo area to the right in front of the axles - Cut-outs in the outer frame of the cargo area and lift bed for attaching tie-down straps (LC 2,000 daN) - 11 pairs of recessed, fold-out lashing rings in the outer frame of the cargo area (LC 10,000 daN): 3 pairs in the lift bed outer frame, 8 pairs in the cargo area outer frame - 11 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 3 pairs in the lift bed, 8 pairs in the rear cargo area - Control valves for the hydraulic ramps located on the right side of the vehicle - 1 pair of foldable mechanical rear supports, single-hand operation HYDRAULIC LOADING RAMPS: - 1 pair of two-part AXS steel ramps, approx. 4,920 mm long, and a

Condition: used, axle configuration: 3 axles, first registration: 04/2019, loading space length: 9,200 mm, loading space width: 2,540 mm, suspension: air, tire size: 245/70R17.5, color: grey, Year of construction: 2019, Faymonville F-S43-1AAF 660 cm Extendable Hydraulic ramps Winch Forced steering = Further information = Tire size: 245/70R17.5 Suspension: Air suspension Front axle: Twin tires; Steered; Tire tread depth left inner: 50%; Tire tread depth left outer: 50%; Tire tread depth right inner: 50%; Tire tread depth right outer: 50% Middle axle: Twin tires; Steered; Tire tread depth left inner: 50%; Tire tread depth left outer: 50%; Tire tread depth right inner: 50%; Tire tread depth right outer: 50% Rear axle: Twin tires; Steered; Tire tread depth left inner: 50%; Tire tread depth left outer: 50%; Tire tread depth right inner: 50%; Tire tread depth right outer: 50% Unladen weight: 13,500 kg Payload: 47,500 kg GVW: 61,000 kg Model number: F-S43-1AAF / EXTENDABLE / HYDRAU = Company information = ALL PRICES ARE NET FOR EXPORT. Joris Versteijnen (NL-DE-GB), Wouter Greutink (NL-DE-GB-ES-IT). Govorim po ryccki. We do our best to provide accurate information, but no rights can be derived from the information provided. Bedpfxezinble Afmslk

Condition: new, maximum load weight: 36,040 kg, overall weight: 53,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: * Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm * Gooseneck hydraulically raisable/lowerable and extendable * For tractor unit: 6 x 4 or 8 x 4 Low-bed: * Low-bed with external beams in an extendable SUPER LOW design, length approx. 8,000 mm * Low-bed with a fixed hardwood floor approx. 40 mm thick and mechanical locking system * The supply lines are protected in the extendable beams and automatically adjust to the respective low-bed length * 7 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 6 pairs of threaded blocks on the inner beam for mounting screw-on RUD rings Rear chassis: * Rear chassis with closed outer frame and diamond plate cover * Chassis with excavator bucket, which is closed in the rear half to accommodate the air tanks * 3 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 1 pair of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings, horizontally, at the front and rear of the chassis (LC 10,000 daN) Axles: * BPW axles and suspension, all axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tires: * Tires 245/70 R 17.5 3PMSF - at the manufacturer's choice. Load index (146/146F) Braking system: * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Paint: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Topcoat with 2 layers of 2K topcoat, solid color in RAL 3002 carmine red, according to the RAL 841GL system Includes accessories: Bsdpfsy Uwu Isx Afmslk * 2-inch kingpin * One galvanized steel front bulkhead, approx. 400 mm high * Yellow-red air couplings on the galvanized connection strip at the front * Trailer steering, operable from the front and rear via cable remote control with push buttons, with single-axle steering control (without installation in the tractor unit) * Preparation for mounting screw-on container positioning for 1 x 20', 1 x 40' or 1 x 45' containers on the outer beams. Without container locking mechanisms * Hydraulic connections from the gooseneck to the low-bed with multi-coupling instead of screw couplings * Electro-hydraulic unit * Spiral cable for supplying the electro-hydraulic unit and/or the electric winch (approx. 35 mm², approx. 3.5 m long, max. 250A) between the semi-trailer and the tractor unit with plug connection (NATO-NATO) * Yellow reflector tape according to EU regulations on the side, on the extension and at the rear of the semi-trailer * On the gooseneck and at the rear, left and right, one bracket each for the warning signs, including a socket * Manual and description on a USB stick * Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection around the pumps * 7 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD VLBG-4 rings * 2nd driving height, approx. 50 mm above the normal driving position, by means of manual operation * On the gooseneck, plug-in aluminum side panels and rear panel, approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in frames are removable (length of the superstructure

Condition: new, maximum load weight: 37,619 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 9,240 mm, loading space width: 2,550 mm, total width: 2,550 mm, total height: 3,570 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer K.SLS 3 / 0N ? 18/30 | Year of Manufacture 2025 | NEW | 40t Ramps | Top Specification Location: Germany Condition: New / Unused Availability: Immediately --- Description For sale is a brand-new Kässbohrer K.SLS 3 / 0N ? 18/30 low-loader, year of manufacture 2025. Perfect for transporting construction machinery, equipment, and heavy goods. Robust chassis, high-quality axles, heavy-duty ramps — ready for immediate use. --- Technical Data Dimensions: - Overall length: 13,190 mm - Platform length: 9,240 mm - Platform height: 875 mm - Overall width: 2,550 mm (+600 mm with side extensions) - Gooseneck length: 3,950 mm - Unladen weight: approx. 10,381 kg Weights: - Permissible gross weight at 80 km/h: 48,000 kg - Permissible gross weight at 60 km/h: 52,800 kg - Total axle load: 30,000 kg - Kingpin load: up to 18,000 kg --- Chassis & Axles: - 3 BPW axles, air suspension, drum brakes - 1 trailing axle at rear - Lift axle (load-dependent + automatic control from the cab) - Tyres: 245/70 R17.5, M+S + 3PMSF - Tyre pressure monitoring R141 - Wabco EBS 4S/3M, ABS + RSS - Wabco Smartboard (axle load, suspension, diagnostics, etc.) --- Ramps & Loading Area: - Foldable 40t access ramps - Ramp length: 2,750 mm - Ramp width: 850 mm - Hydraulic sliding system - 45 mm hardwood floor + chequer plate over wheel arches --- Load Securing: - Multiple 8,000 daN and 13,400 daN lashing points - 7×2 stake pockets + plug-in stakes - Container locks for 1×20 ft - 450 mm front wall, side and rear walls made of aluminium --- Body & Chassis: - High-strength S700 MC steel - Partially metallised (Zn/Al 85/15) — strong corrosion protection - Rear angle: 10°, 500 mm - 2" kingpin - Mechanical landing legs at front - 45t supports at rear Bljdpex Efzuofx Afmjk --- Equipment: - 2× toolboxes - All-round warning beacon - LED lighting - Rear work lights - Wheel chocks - 9×2 extensions (up to +300 mm) - Stake box - Reflective strips on sides & rear --- Colour: RAL 3020 Traffic Red We are happy to provide further information upon request.

Condition: used, functionality: fully functional, power: 48 kW (65.26 HP), fuel type: diesel, empty load weight: 7,475 kg, Year of construction: 2010, operating hours: 8,809 h, drive type: Diesel, Mini excavator Technical condition: good Description: Excavator - tracked excavator - mini excavator TAKEUCHI TB 175 - - Year of manufacture 2010 - - 8809 operating hours - - hydraulic quick coupler - - -MARTIN-POWERTILT - - AIR CONDITIONING - - 2 pcs. digging buckets 40 + 60 cm - - 1 pc. ditching bucket 150 cm - - - 4-cylinder YANMAR diesel engine 48.2 kW - - - rubber tracks approx. 50% - - DIESEL FUELING PUMP - - 3rd + 4th control circuit - - 12-volt system - - - good original condition Quick coupler, buckets, 3rd valve, 4th valve, rear work light, front work light, heater, fully enclosed cab, air conditioning Bledpszqxipsfx Afmek

Condition: used, mileage: 433,000 km, power: 360 kW (489.46 HP), first registration: 08/2017, fuel type: diesel, axle configuration: 6x4, wheelbase: 49,000 mm, fuel: diesel, brakes: engine braking, color: white, driver cabin: day cab, gearing type: mechanical, emission class: euro6, Year of construction: 2017, Equipment: air conditioning, crane, = Additional Options and Accessories = Bedpfx Afezcqc Tomelk - Power brake booster - Rear-view camera = Notes = Palfinger PK18002 truck with crane – 3x hydraulic extensions – Radio remote control – Rotator with grab function – 6.50 m platform – Air conditioning – Reinforced engine brake – Camera – Gross weight 26,000 kg – Unladen weight 14,367 kg – Wheelbase 4,900 mm = Further Information = Application: Construction Front axle: Steered Engine displacement: 12,777 cc Unladen weight: 14,367 kg Payload: 26,000 kg GVW: 26,000 kg Crane: PALFINGER PK18002 – 3x hydraulic, mounted at rear of chassis Please contact Miguel Cubas for further information. = Company Information = We are located between Antwerp and Brussels along the A12 motorway, near the port of Antwerp. Opening hours: Monday to Friday continuously from 8:30 am to 7:00 pm.

Condition: new, maximum load weight: 37,350 kg, overall weight: 45,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Chassis: * Welded construction made of high-quality steel profiles with continuous crossmembers for high ground and point load capacity, with a heavy-duty outer frame. * Loading platform at the rear as a steel welded structure with two welded-in tracks made of 5-hole steel sheet (hole pattern System Lohr/Rolfo) with a length of approximately 2,250 mm, hydraulically lowerable by approximately 350 mm. * Integrated loading platform at the rear of the vehicle, approximately 1,500 mm, hydraulically extendable as a steel welded structure with 5-hole steel sheet (hole pattern System Lohr/Rolfo) cover, light fitting, and 2 ramp compartments and ramp supports. * The drive and control of the rear section are provided by an electric hydraulic unit mounted in a stainless steel box on the left of the chassis, with a radio remote control. * Power supply via the vehicle battery of the towing vehicle. * NATO socket on the front wall, without connecting cable to the tractor unit. Fifth wheel coupling: * 2-inch kingpin, replaceable from below. Under-ride protection: * According to EC, permanently mounted. Support legs: * 2 x 12 t support winches with a 2-speed gearbox. Axles: * 3 x 10 t air-suspended axle unit, manufacturer SAF with disc brake approximately 370 x 45 mm, ABS, wheel connection 10-hole center-mounted ET120, total stroke of the air suspension approximately 200 mm, of which lifting approximately 140 mm and lowering approximately 60 mm, control of the air suspension via hand control with stop function. Steering axle: * 3rd axle as a trailing steering axle with manual and automatic reverse steering lock. Bsdpfxsy Up S Ss Afmolk Lift axle: * 1st axle automatically liftable, also switchable via operation on the chassis frame or via PIN 12 of the light socket. Tires: * 6 tires, 445/45R19.5, manufacturer of our choice, mounted on rim 14.00X19.5, 10-hole ET120. Fenders: * According to EC, 1/4 PVC fender in front of and behind the wheels of the 1st axle in front and behind, 2nd and 3rd axles in the rear. Tire chock holder: * None Braking system: * Two-line braking system according to EC with EBS, automatic load-dependent control. * Spring brake accumulator as parking brake acting on 2 axles, interlock-protected coupling heads permanently mounted on the front crossmember, without connecting line to the tractor unit. Manufacturer Wabco. Lighting system: * According to EC, 24 volts, multi-chamber rear lights, license plate lights, LED side marker lights, LED position light white in front and LED side marker lights at the rear, 15-pole socket and 2x7-pole sockets permanently mounted on the front crossmember, without connecting lines to the tractor unit. Load securing: * 9 pairs of folding lashing rings evenly distributed, tensile force approximately 8 tons. * 7 pairs of folding lashing rings evenly distributed, tensile force approximately 2.5 tons. * 2 pairs of folding lashing rings at the rear of the vehicle, tensile force approximately 2.5 tons. * In the outer frame, holes for lashing straps at approximately 500 mm intervals. Lashing stakes: * 16 lashing stakes approximately 100/40 mm, approximately 800 mm usable length. Lashing stake pockets: * 8 each on each side embedded in the outer frame. * 4 rows of stake pockets transverse to the loading area. Fl

Condition: used, empty load weight: 10,600 kg, maximum load weight: 22,500 kg, overall weight: 33,100 kg, axle configuration: 3 axles, first registration: 12/1984, loading space length: 11,900 mm, loading space width: 2,730 mm, loading space height: 950 mm, suspension: steel, tire size: 7.50R15, color: grey, mileage: 1,001 km, gearing type: other, driver cabin: other, Vehicle location: Bovenden, 3 axles, SAF axles, leaf spring suspension, lashing points, 2-part loading ramps, mechanical ramps, side aluminum fender, supports, twin tires. Superstructure: 3-axle semi-trailer with 2-part mechanical loading ramps. Loading length of the lower platform approximately 8900 mm! ACCESSORY INFORMATION IS WITHOUT GUARANTEE; subject to changes, prior sale, and errors! Bledpji Rp A Nefx Afmok

Condition: used, Year of construction: 1994, tank capacity / l feed pressure / bar Bledezmapcopfx Afmek weight / kg

Condition: good (used), Year of construction: 2002, Hydraulic unit, hydraulic pump, hydraulic pump, universal unit, hydraulic station -Manufacturer: Couperus Hydrauliek, hydraulic station made of slats/blind production -Housing: material VA -Motors: 5x elsto 1.5 kW -Pressure: up to 250 bar Bedpfx Afjpy Rx Temelk -Flow rate: 10 l/min -Individual components: see photos -Dimensions: 2100/660/H1040 mm -Weight: 554 kg

Condition: good (used), Hydraulic cylinders, support cylinders, hydraulic rams, pressure rams, swivel cylinders -Manufacturer: Orsta, double-acting hydraulic cylinder stroke 320 mm -Type: B2-40/18x320/3 TGL10906 -Piston rod: Ø 18 mm -Hole: Ø 25 mm / distance 525 mm -Dimensions: Ø 60 x 590 mm -Weight: 5.2 kg Bljdpfx Asv I Srijfmek

Condition: used, Hydraulic unit, hydraulic pump, hydraulic pump, hydraulic pump -for: Harbs ZSMV/2 pivot beater -Max. Pressure: 70 bars -Motor: 1.5 kW 1405 rpm -Number: 1x available -Dimensions: 465/260/H520 mm Bljdpfx Afjdwc I Remsk -Weight: 58kg

Condition: good (used), Hydraulic power unit, hydraulic pump, universal power unit, gear pump, double hydraulic pump -Manufacturer: Orsta, Double hydraulic pump Bedpfx Ajibd Sxjfmjlk -Pump 1: Type A 16 R -Pump 2: Type C16-3R -Motor: VEM 11 kW / 1440 rpm -Number: 2x hydraulic power units available -Price: per piece -Dimensions: 840/270/H335 mm -Weight: 107 kg/unit