Used Nimo-Kg Skv 200 Mk for sale (71,813)

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame Hsdpfsx A U Ncjx Ampsl • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: used, functionality: fully functional, Year of construction: 2023, total length: 2,300 mm, load capacity: 16,000 kg, fork length: 2,400 mm, empty load weight: 1,100 kg, construction height: 1,230 mm, Forks Load center: 1200 Fork width: 200 mm Fork thickness: 100 mm Hjdpeytklcjfx Ampel Technical condition: good

Condition: used, mileage: 28,930 km, power: 103 kW (140.04 HP), first registration: 11/2020, fuel type: diesel, empty load weight: 3,050 kg, maximum load weight: 450 kg, overall weight: 3,500 kg, tire size: 225/65R16C, axle configuration: 4x2, color: white, driver cabin: other, gearing type: mechanical, emission class: euro6, suspension: steel, number of seats: 2, front tire size: 225/65R16C, rear tire size: 225/65R16C, Equipment: ABS, UVV, air conditioning, cruise control, electronic stability program (ESP), onboard computer, soot filter, traction control, Iveco Daily 35-140 Aerial Work Platform - Work platform model: Versalift LT-36-130TB - Hydraulic drive - Max. working height: 12.2 m - Lateral outreach: 6.00 m - Rotation: 315° - Max. basket load: 200 kg, 2 persons - Operation from the basket or via remote control - Air conditioning - ABS - Driver airbag - Central locking with remote control - 6-speed gearbox - Electric windows and mirrors - Radio CD - EURO 6 - Tyres: 225/65/16C Hodsy H D Ewopfx Ampsl Vehicle from first owner, in very good technical and visual condition. All CE certificates, COC documents, and UVV inspections available. Full TÜV inspection according to §21, UVV test for the work basket, and German registration possible. Yourtrucks Group The Yourtrucks Group maintains business relationships worldwide. Both purchasing and sales extend beyond national borders; for this reason, you will generally find the export price listed in our ads, as it is independent of the place of use. Yourtrucks GmbH compiles the contents of this website with the utmost care and ensures they are regularly updated. Nevertheless, all information provided is non-binding general information and does not replace detailed individual consultation for purchasing decisions. Only the provisions stated in the purchase contract are binding. Subject to change, error, typographical mistakes, and prior sale. Only our general terms and conditions apply. Languages - We speak English - On parle français - ?? ????? ?? ???? - Mówimy po polsku - Hablamos español - Falamos português - Parliamo italiano

Condition: new, Year of construction: 2026, functionality: fully functional, The Impuls Packaging Cobot is an intelligent automation system designed to move and position products efficiently and precisely. It handles the automatic picking, placement, and arrangement of products on pallets or within packaging units, ensuring a smooth and continuous production flow. Thanks to the integrated automation technology, various packing patterns and workflows can be stored directly in the system and recalled as needed. This enables the Cobot to be flexibly adapted to changing products and production requirements without any setup downtime. A range of gripper options is available for the Cobot, including vacuum grippers (either pneumatically operated or with an integrated vacuum motor) as well as specialized gripping systems for different applications. Together with our German partner in the Frankfurt region, we develop the optimal solution for your product to ensure precise, safe, and efficient handling. The system is operated via a user-friendly interface, allowing for easy setup and control without the need for programming skills. The Cobot’s compact design makes it easy to integrate into existing production lines while requiring very little floor space. Using our Cobot increases process reliability and reduces dependence on personnel bottlenecks due to illness or unfilled shifts, ensuring reliable and efficient production even with fluctuating staff availability. Typically, the Cobot pays for itself within the first year. System Features 1. 6-axis cobot robot for moving and placing products 2. Compact, space-saving design 3. Suitable for various pallet sizes Hsdpfx Asyv H T Nsmpsl 4. Multiple packing patterns can be stored and transferred to other systems 5. Easy operation with a graphical user interface, suitable for unskilled staff 6. Low energy consumption, minimal operating costs 7. Available with a variety of gripper options Technical Parameters 1. Maximum product dimensions: L1200mm, W1200mm, H500mm 2. Maximum product weight: approx. 20kg (depending on gripper weight) 3. Packaging speed: 6–10 palletizing cycles/minute (depending on product and pallet size; up to 32 packs/minute possible with multi-pick) 4. Maximum stacking height: 2000mm (600mm additional lift), arm reach up to 1680mm 5. Pneumatic connection required for operation 6. Connection voltage: 3Ph. 380V 50Hz, DC 24V connection 7. Overall power: approx. 3 kW 8. Machine weight: approx. 600 kg 9. Machine dimensions: approx. 3450x1500x3500mm 10. Noise level: > 60 dB We offer different safety concepts for the Cobot: Safety fence: Physically separates the working area so entry into the operation zone is prevented during operation. Safety sensors: Sensors monitor the working area and automatically stop the Cobot as soon as a person or object enters the danger zone. We are happy to advise you on which concept is best suited to your production. When ordering, you can select one of the systems; the other can be supplied for an extra charge.

Condition: used, mileage: 306,165 km, power: 158 kW (214.82 HP), first registration: 02/2017, fuel type: diesel, tire size: 265/70 R19,5, axle configuration: 4x2, fuel: diesel, color: white, driver cabin: day cab, gearing type: automatic, emission class: euro6, suspension: steel-air, number of seats: 3, permissible axle load (axle 1): 4,480 kg, permissible axle load (axle 2): 8,480 kg, loading space length: 6,200 mm, loading space width: 2,450 mm, loading space height: 2,400 mm, Year of construction: 2017, Equipment: ABS, air conditioning, central locking, cruise control, electric window regulation, power mirror, spoiler, tail-lift, trailer coupling, = Additional options and features = - Roof spoiler - Remote central locking - Speed limiter - Air suspension - Radio - Reversing camera - Side door - Sun visor = Notes = Dhollandia DHLM.20 tail lift, 2000 kg Loading platform 175 cm Internal dimensions of loading area: L 620 × W 245 × H 240 Rearview camera Tow bar Cruise control Side door Step Sun visor Wooden interior paneling Overall condition: damages all around = Further information = General information Model year: 2026 Registration number: 47-BJF-8 Technical information Number of cylinders: 4 Engine displacement: 5,132 cc Axle configuration Axle brand: Anders Brakes: disc brakes Front axle: Tire size: 265/70 R19.5; Max. axle load: 4,480 kg; Steering axle; Tire tread left: 30%; Tire tread right: 30%; Suspension: leaf springs Rear axle: Tire size: 245/70 R19.5; Twin tires; Max. axle load: 8,480 kg; Tire tread left inner: 35%; Tire tread left outer: 35%; Tire tread right inner: 35%; Tire tread right outer: 35%; Suspension: air suspension Weights Unladen weight: 6,075 kg Payload: 5,915 kg Gross vehicle weight (GVW): 11,990 kg Functional Tail lift: Dhollandia DHLM.20, tailgate, 2,000 kg Interior Interior color: grey Maintenance, history and condition APK (Technical Inspection): valid until 02/2027 Hodpfx Aoy E Hkaompel General condition: moderate Product safety Manufacturer: Nijwa Used Trucks Vormerij 12 7621HL BORNE, NL

Condition: used, mileage: 329,095 km, power: 92 kW (125.09 HP), first registration: 12/1988, fuel type: diesel, tire size: 405/70 R 20, axle configuration: 4x4, wheelbase: 2,620 mm, fuel: diesel, color: orange, gearing type: mechanical, number of gears: 16, number of seats: 3, total length: 4,390 mm, total width: 2,330 mm, total height: 3,200 mm, permissible axle load (axle 1): 4,000 kg, permissible axle load (axle 2): 4,000 kg, Year of construction: 1988, Equipment: differential lock, General information Number of doors: 2 Registration number: T-36-HKP Technical information Number of cylinders: 6 Engine capacity: 5.917 cc Drivetrain Make of engine: Mercedes-Benz Axle configuration Tyre size: 405/70 R 20 Brakes: disc brakes Suspension: coil spring suspension Front axle: Differential lock; Max. axle load: 4000 kg; Steering; Tyre profile left: 50%; Tyre profile right: 50% Rear axle: Differential lock; Max. axle load: 4000 kg; Tyre profile left: 50%; Tyre profile right: 50% Condition Number of keys: 2 = Dealer information = Hodpfx Aey Ewhijmpsl For more photos see: Why you buy from Thomas Trucks? That choice is simple. Thomas Trucks is one of the independent trading companies worldwide in the field of used commercial vehicles. Here you can choose from an ever-changing stock of second hand trucks, tractors, trailers and trailers. Our offer includes all European brands, construction years and price ranges. Here you will always find a good vehicle for the right price! Thomas Trucks always has: - Sharp prices - Good service - Spacious, rapidly changing stock - Known quality - Decent business - We speak many languages - Accompaniment input and transport - (Export) license plate quickly arranged - Professional technical services - And more. Visit the website: and view our complete range and competitive offers We are open 6 days a week. Do you need help with exporting, importing, or shipping your vehicle? Contact our sales team. Selling your current vehicle to us is also possible. We do our best to display the data as accurately as possible, however no rights can be derived from this data We can also arrange financing for you within the Netherlands.

Year of construction: 2022, condition: used, Cream cooker – MESH MASZ – Model: MK200Z – Excellent condition Heating and mixing — Cream cooker — heating, fusion, infusion, cooking, mixing, vaporization. Used in the production of cream and other products that need to be mixed and heated up to a maximum temperature of 150°C. MK cream machines – Bowl capacity: 200 litres Hedpfx Ajy Enzmompol MK machines are used for the production and preparation of choux pastry, creams, ointments, fruit, icings, sauces, fillings, compounds according to your own recipes and for all products requiring uniform heating and simultaneous, gentle mixing.

Condition: new, Year of construction: 2026, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Hydraulic piping Pipeline construction Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 800-900 kg (depending on version) Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Pipe calculation software Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site Hsdpfx Aong Exasmpel - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, THE ECONOMICAL BENDING MACHINE FOR TIGHT BENDING RADII: The bending machine with free-standing bending head can be easily converted to right and left bending for difficult geometries. The plug-in bending tools allow quick conversion to other tube sizes. Fast hydraulics to shorten non-productive times is an important factor for series production. The clamping pressure for tube clamping can be optimally adjusted. The PLC control (arbitrarily expandable via USB stick) with data memory and latest X2X interface, can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for max. 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The machine has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. This excludes incorrect positioning within a tolerance window and thus minimizes the user-related error rate. General error messages are displayed on the large screen with full text. The mandrel retraction is programmable and can be retracted automatically ahead of time when the bending angle is reached. Hjdpsndn Agefx Ampsl The compact drive unit with the detachable mandrel carrier offers advantages for use at the assembly site as well as for special designs with a very large tube feed and is also available as a stationary variant with a tidy system for tools and mandrel bars. The low-cost alternative to the fully controlled CNC machine. POSSIBLE APPLICATIONS: Hydraulic piping Pipeline construction Plant construction, e.g. chemical industry Metal construction Sample construction Technical data: Bending capacity Ø 6 to 50 x 4 mm depending on material bending radius min/max: 10 mm/140 mm Bending radius min: 1,5 x Ø (standard 2 x Ø) Multifunctional machine control Bending angle adjustment (0.1°) Mandrel beam lengths 1500/3000/4500/6000 mm (special version also longer) Maximum 180º bending result Weight 600-700 kg (depending on version) Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Automatic mandrel lubrication (minimum quantity) Pneumatic or hydraulic quick-action chuck Positioning of length and torsion via automatic brake function or via manual stops by foot switch Semi-automatic positioning of length and rotation via servo motors Pneumatic rotation stop Pipe calculation software Laser-supported tool monitoring for monitoring the tool tension 10 inch touch screen with integrated tube calculation Bending radius up to 250 mm Data transfer via cable (LAN), wireless (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, PROFILE BENDING ATTACHMENT PB20 The PB20 profile bending attachment is the optimal supplement for tube bending on the 3000 and 6000 models. The device can be easily and quickly mounted on the bending shaft without the use of tools. The workpiece is clamped onto the turntable with the clamping device and pulled around the bending tool. With this system, leg lengths to be bent can be accurately measured in conjunction with a length stop and can be bent with repeatable accuracy. TECHNICAL DATA: - Bending capacity steel 37: 100 x 10 mm, Ø 20 mm. - Many standard tools available - Special tools possible - Sharp-edged tools with bending radius R2 or 5 mm - round tools R 10 to 25 mm for bends max. 260° optional OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing purchase via Hsdpfx Aenh R Ekompsl the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, the mobile bending machine with great performance: The compact, mobile design enables precise and repeatable bending stationary and directly at the installation site up to a tube diameter of 35 mm, CU 42 mm. A powerful three-phase motor and a precision gearbox provide powerful drive. The motor speed is automatically adjusted, resulting in increased return speed and shorter cycle times. Optimum bending accuracy and very high repeatability are achieved by position detection directly on the bending axis. The bending angle is easily and quickly set to 0.5° using pushbuttons. The large LCD display clearly shows the angles. The storage of up to three bending angles enables the rational bending of tubes with different bending results. For transport, the compact unit with accessories can be neatly and safely stored in sturdy transport cases. The "upright tube and rotating tool" principle ensures low space requirements during bending. Sliding shoes are used for thin-walled tubes to enable crease-free bending and to bend bends with the slightest deformations from, for example, stainless steel and copper tubes. With the PB20 profile bending attachment, flat, square and round iron can be bent without problems. POSSIBLE APPLICATIONS: - Hydraulic piping - Sample construction - Sanitary and heating construction - Technical data: - Bending capacity Ø 6 to 35 mm, CU Ø 42 mm depending on material. - Bending radius min/max: 36 mm/150 mm - Precise digital bending angle adjustment 0.5°. - Maximum 180º bending result; for special applications Endless operation possible - Hexagonal shaft 40 mm for quick tool change - Safety foot switch with emergency stop function - Alternating current 230 V connection - Weight 29 kg - Frequency converter and three-phase motor - 3 bending angles storable OPTIONAL ACCESSORIES: - Slide shoe holder - double roller holder - Profile bender PB20 - for bending flat and square bars up to Hodpenfvx Njfx Ampsl max. 80 x 8 mm, round bars up to max. 20 mm - tripod base - machine case - tool case - Small bending device KBV - Special tool according to specification OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, machine/vehicle number: 1018, THE POWERFUL BENDING MACHINE FOR EXTREME USE: The compact bending machine enables precise and repeatable bending up to an outer diameter of 100 mm stationary and directly at the assembly site. Transport is possible with lift trucks or the optional rollers. A powerful three-phase motor and a precision gearbox provide a powerful drive. The machine convinces with its compact and slim design as well as the very free bending range. Optimum bending accuracy is achieved by position detection directly on the bending axis. The bending angle is set easily and quickly via a convenient and menu-driven user interface in 14 languages with touchscreen control, which guarantees even more intuitive operation. For more complex bending tasks, 100 bending programs can be stored, with an angle sequence of max. 8 bends per geometry. The multifunction control allows variable adjustment of the bending speed for forward and backward travel, and a parameterizable overbending function is provided to compensate for material springback.With the help of the four material characteristics, the material is automatically overbent to the required bending angle, thus realizing an exact bending result. The principle of "stationary tube and rotating tool" ensures low space requirements during bending. Sliding shoes are used for thin-walled tubes to achieve a wrinkle-free bending result and to bend bends with minimal deformations from e.g. stainless steel and copper tubes. With the profile bending attachment PB20 flat, square and round bars can be bent without any problems. Extremely small bending radii are made possible with the KBV small bending attachment. POSSIBLE AREAS OF APPLICATION: - Plant engineering - Hydraulic piping - Meander bending - prototyping - Sanitary and heating engineering - shipbuilding TECHNICAL DATA 10000: Bending capacity: up to 100 x 5 mm, 55 mm solid material three-phase current 400 V - Bending radius up to 500 mm - Multifunctional machine control Bending angle adjustment (0,1°) - Maximum bending angle 240 - Safety foot switch with emergency stop - Weight 600 kg OPTIONAL ACCESSORIES: Hedpfx Amsndk N Aopjl - Adapter system for tools from model series 3000/6000 with bending radius from 45 mm, incl. hexagonal shaft 40 mm - Profile bender PB20 - for bending flat and square bars up to max. 100 x 10 mm, round bars up to max. 20 mm - Small bending device KBV - Special tools according to specification - Software adaptations for special tasks OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, machine/vehicle number: 1018, THE MANDREL BENDER WITH MANUEL CLAMPING: This mandrel bending machine with manual eccentric quick clamping for tube fixing enables rational bending. The compact drive unit with the detachable mandrel carrier offers advantages when used at the assembly site. Optimum bending accuracy is achieved by position detection directly on the bending axis. The bending angle is set easily and quickly via a convenient touchscreen control with menu-driven user interface. The comfort control allows two speeds as well as a parameterizable overbending function to compensate for material springback. The bending sequence is significantly shortened by automatic "free travel" at the end of the sheet. For more complex bending tasks, bending programs can be stored with a maximum angle sequence of 50 bends per geometry. An almost unlimited number of programs can be stored on the control or a USB stick, as well as 200 materials. The plug-in bending tools allow rapid conversion to other tube sizes. For difficult geometries, the bending direction of the machine can be changed to right or left bending as standard. The open bending unit allows, for example, the bending of railing frames with only one weld seam. The optional calculation software on the PC determines the cut length for the entire geometry as well as the travel distance, twisting angle and bending angle for each bend. The mandrel retraction is programmable and can be retracted automatically ahead of time when a bending angle is reached. POSSIBLE APPLICATIONS: - Plant engineering, e.g. chemical industry - hydraulic piping - prototyping - Pipeline construction TECHNICAL DATA: - Bending capacity Ø 6 to 50 mm - bending radius min/max: 10 mm/140 mm - Bending radii 2 x D - multifunction machine control bending angle adjustment (0,1°) - mandrel beam lengths 1500/3000/4500/ 6000 mm (special version also longer) - Maximum 180º bending result - Weight 300-500 kg (depending on version) Optional accessories: - Automatic mandrel lubrication (minimum quantity) - Digital displacement measurement for length and twist (resolution 0.1 Hedpfx Amjnfvy Uepel OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing-purchase via the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, THE ECONOMICAL MANDREL BENDING MACHINE FOR TIGHT BENDING RADII. For tube dimensions from 20 - 90 mm, this bending system offers solutions for complex geometries with standard radii of 2xD. Depending on material quality and wall thickness ratio, radii of 1.5xD can also be realized suitable for series production. With a tool height of 120 mm, there are also sufficient options for special profiles. The extremely precise and powerful electric drive of the bending axis as well as the stable and rigid construction of the mandrel carrier and the bending arm also contribute to the desired bending result. The plug-in bending tools allow a quick changeover to other tube dimensions. The clamping pressure for the tube clamping can be optimally adjusted. The PLC control (can be expanded as required via USB stick) with data memory and the latest X2X interface can accommodate an almost unlimited number of programs for bending angle, linear dimension and twisting angle for a maximum of 50 bending sequences on one tube length. A freely programmable database for up to 200 materials is available for monitoring springback values. The control system has 2 operating modes: In "Simple Bending", the length and twist of the bends relative to each other are automatically displayed. In the "Controlled bending" mode, the data is stored beforehand and a permanent target/actual comparison is performed during bending. Also available with pneumatic rotation stop or with gear-assisted length and twist positioning. POSSIBLE AREAS OF APPLICATION: - Plant engineering, e.g. chemistry - hydraulic piping - metal construction- prototype construction- pipeline construction TECHNICAL DATA: Bending capacity 7000: Ø 20 to 70 x 5 mmbending capacity 9000: Ø 20 to 90 x 5 mm depending on the material- bending radius min/max: 40 mm/250 mm- Bending radii min: 1.5 x Ø (standard 2 x Ø ) - Multifunction machine control Bending angle adjustment (0,1°) - Mandrel support lengths 3000/4500/6000 mm - Maximum 180º bending result - Weight 1600-3200 kg (depending on version) - Ergonomic operation via safety foot switch OPTIONAL ACCESSORIES: Hjdpfxsnh R Suo Ampel - Automatic mandrel lubrication (minimum quantity) - Pneumatic or hydraulic quick chuck - Larger bending radius up to 300 mm - Positioning of the length and twist via automatic brake function or via manual stops by foot switch - Semi-automatic positioning of the length and twist via servo motors - Automatic tool retraction - Pipe calculation software - 10 inch touch screen with integrated tube calculation - Data transfer via cable (LAN), via radio (WLAN) or USB OUR SERVICE: - Welcome to the test production in our house in the demo room - Consultation and information meeting at your site - Consultation and handling as leasing/financing purchase via - the company JUTEC - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, THE PRECISION 3-ROLL BENDING MACHINE When developing the compact and mobile horizontal bending machine, the focus was clearly set on the production of dimensionally accurate coils such as handrails for spiral staircases. This is the supreme discipline, since two mutually influencing variables (radius and pitch) must be combined in a bend to form a dimensionally accurate geometry. The interaction of tube calculation on the PC, implementation on the bending machine, and control via the measuring equipment with final correction of the bending values ensure accurate bending. By simple and few inputs into the PC tube calculation program, the local printer provides a printout and supports the calculation of all necessary bending and correction data to operate the machine. A new powerful drive concept allows infinitely variable adjustment of the bending speed, requiring only a 230 V (AC) connection. Hardened steel tools as well as hard plastic tools that are gentle on the surface are available for selection. To ensure optimum feed even with tight bending radii, all three bending shafts are driven. The drive concept also proves its worth in tough daily use on the flat, when bending tubes and profiles. Customers of the 4800, 5000 and 6000 bending system have the option of purchasing the roller bending unit without the drive. The roller bending unit with the designation RB43, can be adapted to the bending systems 4800, 5000 and 6000 via the bending shaft. In this case, the machines act as a drive unit. POSSIBLE APPLICATIONS: - Handrails/bottom rails for spiral staircases - Large tubular profile bends - General metal construction TECHNICAL DATA: Hedpjng A R Sofx Ampol - Bending capacity Ø 10 to 60 mm - bending radius min: 300 mm at Ø 42,4 mm - Bending direction right and left - Digital bending adjustment for radius and pitch - Safety foot switch with emergency stop function - Maintenance-free robust three-phase motor - Construction site suitable 230 V connection - Weight 280 kg OPTIONAL ACCESSORIES: - Support roller - for stabilization - Lifting roller - to produce controlled slope - MGR - measuring device to determine the correct radius - MGV - measuring device to determine the correct slope based on torsion - MPW - PC calculation program to determine the correct bending values - RB4303 - universal bending tool for profiles up to 60 mm height - Tools for special profiles OUR SERVICE FOR YOU ON SITE: - Welcome to the test production in our house in the demo room - Consultation-information meeting at your site - Consultation and handling as leasing/financing purchase via - Service contracts, maintenance at your site

Condition: new, Year of construction: 2025, machine/vehicle number: 1018, THE POWERFUL BENDING MACHINE FOR WORKSHOP AND ASSEMBLY. The compact and mobile bending machine enables precise and repeatable bending up to an outer diameter of 60 mm stationary and directly at the assembly site. A powerful three-phase motor and a precision gearbox provide a powerful drive. Optimum bending accuracy is achieved by position detection directly on the bending axis. The bending angle is set quickly and easily via a convenient, menu-driven user interface with touchscreen control, which guarantees even more intuitive operation. For more complex bending tasks, 100 bending programs can be stored, with an angle sequence of max. 8 bends per geometry. The multifunction control allows variable adjustment of the bending speed for forward and backward travel, and a parameterizable overbending function is provided to compensate for material springback. With the aid of the four material characteristics, the material is automatically overbent to the required bending angle, thus realizing an exact bending result. The "stationary tube and rotating tool" principle ensures low space requirements during bending. Sliding shoes are used for thin-walled tubes to achieve a wrinkle-free bending result and to bend bends with minimal deformations from e.g. stainless steel and copper tubes. With the PB20 profile bending attachment, flat, square and round bars can be bent without any problems.Extremely small bending radii are made possible with the KBV small bending attachment. POSSIBLE AREAS OF APPLICATION: - Plant engineering- Hydraulic piping - Meander bending- prototyping- Sanitary and heating construction Hsdpfx Ajng Ax Ssmpjl TECHNICAL DATA: Bending capacity 6000S: Ø 6 to 50 x 4 mm alternating current 230 V Bending capacity 6000D: Ø 6 to 60 x 4 mm Bending capacity 6000DS: Ø 6 to 60 x 5 mm three-phase current 400 V Bending capacity 6000D: Ø 6 to 60 x 4 mm three-phase 400 V - Bending radius min/max: 36 mm/280 mm - Optional large bending radii up to 500 mm - Multifunction machine control Bending angle adjustment (0.1°) - Maximum bending angle 240 - Hexagonal shaft 40 mm for quick tool change - Safety foot switch with emergency stop - Weight 110 kg OPTIONAL ACCESSORIES: - Profile bender PB20 - for bending flat and square iron up to max. 100 x 10 mm, round iron up to max. 20 mm - Roller bender RB43 - The RB43 is placed on the 6-edge shaft of the bending axis. By switching over to endless bending, the bending system acts as a drive unit. - Small bending device KBV - Special tool according to specification OUR SERVICE FOR YOU ON SITE: - Welcome to the test production in our house in the demo room - Consultation-information meeting at your site - Consultation and handling as leasing/financing purchase via - Service contracts, maintenance at your site

Condition: new, power: 345 kW (469.07 HP), fuel type: diesel, overall weight: 27,000 kg, axle configuration: 3 axles, brakes: retarder, color: red, gearing type: automatic, loading space length: 6,400 mm, Equipment: ABS, air conditioning, crane, electronic stability program (ESP), navigation system, parking heater, soot filter, You can find our complete inventory of vehicles that are immediately or shortly available on our website. Excerpt from features. Full list of features available upon request. VOLVO FH 460 6x2R NLA: * Euro 6 emissions standard * 12.8 L diesel engine with turbocompound charger, 469 HP/345 kW, 2,652 Nm * Volvo Engine Brake+ (VEB+) * Braking performance: 340 kW/462 HP (D13S), 430 kW/585 HP * I-Shift AT2612, automated 12-speed gearbox (direct drive), max input torque: 2,652 Nm * Liftable axle * Driver Comfort Package Extended * Air conditioning with automatic temperature control * Cab heater, 2 kW * Front axle air suspension * Front axle suspension lift: Basic (increased ground clearance, reduced lift range) * Maximum front axle load: 8.0 t (technical) * Maximum rear axle load: 19 t (technical) * Trailing axle 7.5 t * Disc brakes, solid discs * EBS, Electronic Braking System, Medium package * Rear air suspension * 630 L aluminum fuel tank right, D-shape, 560 mm high, 2030 mm length * AdBlue tank, usable volume 48 liters, 560 mm height * Front axle tires 355/50R22.5 * Rear axle tires 295/60R22.5 * Trailing axle tires 355/50R22.5 * Digital tachograph, generation 4 * Speed limiter 90 km/h * Electronic Stability Program (ESP) * Adaptive traction control * Adaptive cruise control (ACC) with collision warning and emergency braking function * Emergency brake assistant not deactivatable * Lane departure warning system * Side collision avoidance and turning assistant (both sides) * Driver alert system (fatigue warning) * Radio reception: AM/FM and DAB/DAB+ (analog & digital) * Reverse monitoring/camera * Second driver information display, 9-inch touch color display * I-Park Cool (integrated stationary air conditioning with automatic temperature control) * Cab in red, similar to RAL3002 * LED main headlights * LED daytime running lights, V-light * Front LED fog lamps * Two LED rotating beacons (orange), mounted on front of cab roof * 4 spotlights on the VOLVO roof bar * Ringfeder RF4040A G-150 trailer coupling (observe D-value/max. trailer load!) * Electrical connection for trailer, 15-pin (ADR possible) Container flatbed superstructure: * Low design * Inner flatbed dimensions: approx. 6,400 x 2,480 x 600/1,900 mm * 2 pairs of container locks, extendable to approx. 3 m to accommodate 20-foot containers MKG loader crane HLK 531 HP a6: * Reach / lifting capacity: - 4.35m / 10,350 kg - 5.90m / 7,450 kg - 7.85m / 5,450 kg - 9.90m / 4,200 kg Hsdpfoxcdmwjx Ampsl - 11.95m / 3,400 kg - 14.1m / 2,850 kg - 16.25m / 2,450 kg * Boom angle +20° * Electronic crane management system ACS3 – ACS3 Plus switchable * Optimized crane utilization by capturing vehicle tilt limits * 6-function radio remote control

Condition: excellent (used), Year of construction: 2020, General Description For sale: 6 hydraulic presses, model YL32-200. These are robust four-column presses, ideal for metal forming, pressing, stamping, bending, and general industrial uses. The machines were originally imported from China and are based on the widely used Y32 series, ensuring easy maintenance and worldwide availability of spare parts. ⸻ ⚙️ Technical Specifications (typical for YL32-200) * Press force: approx. 200 tons * Construction: 4-column hydraulic press * Stroke: approx. 400 – 700 mm * Table size: approx. 700 x 700 mm – 1000 x 1000 mm * Daylight (max. opening): approx. 800 – 1200 mm * Hydraulic pressure: up to 25 MPa * Motor power: approx. 7.5 – 15 kW * Control system: manual / semi-automatic * Power supply: 380V / 50Hz (industrial standard) * Weight per machine: approx. 5 – 8 tons ⸻ 🏭 Applications * Metal forming & stamping * Deep drawing * Straightening and pressing * Plastic forming * Workshop and industrial production ⸻ 📦 Condition * Used condition * Sold as is / ex-works * Inspection possible by appointment ⸻ 📊 Availability * Quantity: 6 machines available * Sale as single units or as a package ⸻ 🚛 Logistics * Location: Germany * Loading possible (forklift or crane required depending on configuration) Hodpfey E Abnox Ampol * International shipping can be arranged * Price per unit!! * Dismantling by buyer!! * Alternatively, dismantling can be organized at an additional cost!

Condition: excellent (used), first registration: 09/2015, loading space length: 20,180 mm, loading space width: 3,000 mm, color: other, Year of construction: 2015, Damages: none YAFTL2007F0017329 = More information = Empty weight: 13.600 kg Carrying capacity: 28.400 kg GVW: 42.000 kg Technical condition: very good Visual appearance: very good Price: On request Registration number: DW205AH = Dealer information = Do you have any questions or suggestions? Please feel free to contact us. We guarantee a response within 8 hours.Prices do not include VAT.No rights may be derived from the information provided.Office phone number: Mobile: Dutch - English - German - French - Spanish - Italian) Available via WhatsApp and Viber.Mobile: Available via WhatsApp and Viber.When paying by bank transfer, the funds must be transferred to our bank account listed below. Always verify the payment details on our website. Please contact us if you have received different information.If in doubt, please call us so we can verify the invoice and/or payment.Bank details: Bank name: ING Bank address: Bijlmerdreef 106 1102 CT Amsterdam IBAN number: NL97INGB0117176699 EORI/VAT/TAX: NL810574901B(01) BIC/SWIFT: INGBNL2A Hedpeymrb Sofx Ampjl

Year of construction: 2015, condition: good (used), Used modern Bystronic Xpert 200/3100 200ton x 3metre cnc pressbrake for sale Year/new: 2015 Working length: 3100mm / 3metre x 200ton Press force: 2000KN / 200ton Max stroke 215mm Total axis: 7axis – y1,y2,x,x1,r,z1,z2 Hydraulic crowning Hjdpogkgwfsfx Ampel Hydraulic tool clamping Fully serviced by Bystronic Uk from new One owner from new Low hours in good working condition

Condition: new, functionality: fully functional, empty load weight: 130 kg, maximum load weight: 620 kg, overall weight: 750 kg, loading space length: 800 mm, loading space width: 2,000 mm, Ingenious and space-saving trailer, ideal for use behind a motorhome. The Roadster-CampV3 trailer, manufactured by DEBON (also known as Cheval Liberte), is designed for transporting motorcycles, scooters, or bicycles. The available accessories include mounts for carrying one to two bicycles and a scooter or motorcycle, as well as additional options to suit any holiday requirement. The motorcycle or scooter can be conveniently rolled side-on directly onto the trailer. A front wheel chock, lashing rings, and a handlebar holder securely fix the scooter or motorcycle, which can be loaded using a ramp onto the trailer platform. The lighting bar of the bicycle trailer is extendable. Two optional classic bicycle racks, such as those used on roof racks, can be mounted on the extension. Standard equipment for the motorcycle transporter or bicycle transport trailer includes lashing rings, an extendable lighting bar, aluminium floor, front bracket for accessories, jockey wheel, folding support stand, robust hot-dip galvanized frame, and a very sturdy V-drawbar. Available accessories: 100 km/h approval, bicycle holders, motorcycle holders, motorcycle tie-down straps, lashing straps, storage box, spare wheel, and anti-theft device. Technical data: Hodpfx Amjwa Rbljpjl Internal dimensions (LxWxH): approx. 80x200 cm Overall external dimensions (LxWxH): approx. 184x225x146 cm Gross weight: 750 kg, unbraked Curb weight: approx. 130 kg Payload: approx. 620 kg Loading platform height: approx. 52 cm 100 km/h configuration: available at extra cost Tyres: 195/55R10C We also offer: · Financing · Leasing (business customers only) · Consultation · Delivery throughout Germany (excluding islands) · Accessories · Rental trailers · Spare parts · Registration service for DH – HB – DEL · Service · Repairs · TÜV inspection for car trailers PKW-Anhänger-Center Ahrens, Moordeicher Landstraße 37, 28816 Stuhr near Bremen Opening hours: Monday - Friday 8:00 am – 5:00 pm

Condition: new, empty load weight: 300 kg, maximum load weight: 450 kg, overall weight: 750 kg, loading space length: 2,250 mm, loading space width: 1,170 mm, loading space height: 1,200 mm, Plywood box trailer Roadstar C220 from manufacturer Cheval Liberté / Debon. The box trailer comes equipped with plywood side walls, a single-wing door, support stands, jockey wheel, lashing points, robust frame, and a V-drawbar. We also offer useful trailer accessories such as lashing rails, lashing straps, and additional lashing points. The body is splash-water protected. Hjdpfx Amsy Efqfjpsl Technical Data: Internal dimensions (LxWxH): approx. 225x117x120 cm Overall external dimensions (LxWxH): approx. 348x163x173 cm Gross weight: 750 kg unbraked Unladen weight: approx. 300 kg Payload: approx. 450 kg Loading platform height: approx. 50 cm 100 km/h version: available at extra cost Tyres: 155/70R13

Condition: used, maximum load weight: 13,950 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 04/2021, next inspection (TÜV): 09/2026, loading space length: 4,880 mm, loading space width: 2,420 mm, loading space height: 900 mm, Equipment: ABS, Schwarzmüller M Series, aluminium side walls left and right, front wall and tailgate made of steel, 90 mm aluminium side walls, SAF Intradrum axles with drum brakes, ABS, ESP, air suspension, 50 mm towing eye, sliding tarpaulin, new technical inspection, trailer has covered 72,000 km, tyres: 3x 70% tread, 1x 50%. The trailer is in good and immediately operational condition. Hjdjy Hy Smopfx Ampsl

Condition: refurbished (used), Year of construction: 2015, Durst P10-200 with Corrugated Option, fully automatic Hodpfx Amsy Amckepel Resolution: 10 pl - 1000 dpi Color: 6C + (optional White) Very low usage Speed up to 2025 m2/h Fully automatic loader (feeder) Fully automatic unloader (stacker) INK: Paper and board with very low odor Options: Corrugated Option with 2 rails for dropping down material Corrugated static bar for different material thicknesses Corrugated software to control media and thickness - Understatic bar and automatic media stop for crash prevention - Caldera Rip Software Demo video is from Durst Rho 750 (28 pl, 600 dpi)

Condition: as good as new (ex-display), overall weight: 3,500 kg, loading space length: 4,550 mm, loading space width: 2,000 mm, loading space height: 300 mm, Large construction machinery transporter, low loader tandem for construction machines, excavators, platforms, scissor lifts, and many other vehicles. Hapert manufactures extremely robust car trailers such as this INDIGO HT-2 455x200cm. The construction machinery trailer can be tilted and conveniently loaded via a very sturdy mesh ramp. An absolute universal trailer, suitable not only for construction equipment but also for transporting lawnmowers, tractors, pallets, bulk goods, and small vehicles. The high-loader car trailer can also be conveniently side-loaded. Hsdpoy Au Nlefx Ampol The machine transporter is equipped with a robust mesh ramp, hand hydraulics for tilting, winch with holder, lashing eyes with 1000kg load capacity, automatic jockey wheel, three-sided foldable aluminum side walls, an extremely durable welded and dip galvanized frame, and a V-drawbar.