Used Lukas Spreader, Lukas Double-Acting Column Actuator for sale (20,172)

Condition: used, Machine not operational - control system not functioning Available at a special price Double-column hydraulic press ALPHA TEC -- ALPHATEC Type RPS 5000 Factory No. 300487, Year of Manufacture 2006 Pressing force: 500 tons Distance between columns (front and rear): 2520 mm Table area: 2500 x 2500 mm Ram area: 2500 x 2500 mm Ram stroke: 600 mm Maximum installation height: 600 mm Table height above floor: approx. 900 mm Tank capacity: approx. 1000 liters Ram retraction force: approx. 22 tons Adjustable forward speed: 100-800 mm/s Pressure build-up to 5000 kN: approx. 0.7 sec. Return stroke speed: approx. 300 mm/s Main motor power: 75 kW Control pump motor power: 2.2 kW Power supply: 400 Volt, 50 Hz Hnjdpsdzqptefx Abkju - 8-fold flat guide for the ram - Hydraulic ram locking in the top dead center position - Adjacent control cabinet (200 x 50 cm) - Electrical control system SIEMENS PLC S7-314 - Operation via SIEMENS OP 170-B (5.7") - 2-hand control panel located beside the machine - Floor-level installation - Table top 2510 x 2530 x 135 mm (approx. 6700 kg) - Central lubrication system - Operating manual with circuit diagrams Space requirement (L x W x H): 372 x 260 x 460 cm Space requirement for horizontal transport (L x W x H): 460 x 372 x 260 cm Weight: approx. 50 tons The machine was used for straightening heated steel flanges. From insolvency – in good condition.

Condition: used, Year of construction: 1986, Pressure total: 500 ton Stroke: 1100 mm Daylight: 1500 mm Table surface area : 2000 x 1250 mm Slide area: 2000 x 1250 mm Die cushion capacity in table: 160 ton Die cushion stroke: 300 mm Approach speed: 650 mm / sec Required power: 55 kW Weight of machine approx.: 50 ton Hsdpfx Absuqdqlekonu Standard configuration The press was completely overhauled mechanically, hydraulically and electrically in 2008.

Condition: used, Year of construction: 1987, pressure 800 t stroke 100 mm Hnodpfx Abozl E Saskeu no. of strokes 45 /min distance between columns 600 mm table surface area 560 x 650 mm capacity of ejector 5 t ejector stroke 15 mm ram surface 590 x 450 mm power requirement 22,0 kW Weight 17,0 t dimensions (WxDxH) 1,7 x 2,55 x 3,1 m Nominal force travel 1,46 mm With knuckle-joint drive, flywheel brake, hydraulic clutch with 2nd brake, press frame balancing, single ejector in table, self-monitoring control

Condition: used, Year of construction: 1997, Technical details: pressure: 160 t distance between columns: 1000 mm stroke: 250 mm dayligth: 600 mm distance table/ram: 600 mm table height over floor: 550 mm table surface area: 810 x 860 mm clamping surface ram: T x B: 720 x 580 mit T-Nuten mm total power requirement: 15 kW weight of the machine ca.: ca. 16,0 t Hedpfx Abou Nfmmskjnu The machine isn't installed yet. The pictures are from the origin location of the former owner. further details: - sideway passage W: 520 x H: 620mm - passage front side W:660mm x H: 600mm equipment: - walkable platform arround the machine= height over floor approx. 2400mm, platform approx. 2700 x 2600 x 1050mm - hydraulic pack - oil cooler i.D. *

Year of construction: 1964, condition: used, pressure 40 t distance between columns 450 mm stroke 20-50 mm ram - range of adjustment 60 mm table surface area 370x400 mm ram surface 250x370 mm Hnedpfx Abslp U Exeksu hole in the table 120x280 mm table height 850 mm weight of the machine ca. 2,5 t dimensions of the machine ca. BxTxH 1600x1300x2800 mm

Condition: used, Year of construction: 1973, pressure 1600 t distance between columns 3160 mm ram stroke 1450 mm Hjdsvxwhwspfx Abkenu distance table/blankh.,max. stroke up,adjustm. up 2250 mm table surface area 4000 x 2200 mm ram pressure 1000 t pressure of blank holder 600 t stroke of blankholder at the bottom 1000 mm stroke of blankholder with adjustment 0-100 mm 1450 mm blank holder size 4000 x 2200 mm die-cushion pressure inside the table 360 t stroke of drawing cushion in table 275 / 400 mm ram surface 4000 x 2200 mm column travel -side 1100 mm die-cushion inside the table hydraulic, controlled die-cushion in pusher hydraulic, controlled oil volume 9000 l total power requirement 390 kW weight of the machine ca. 250 t dimensions of the machine ca. 6,0 x 4,3 x 10,5 m Head press (1600 tons) of a press line with five subsequent presses (800 tons)

Condition: used, Year of construction: 2007, pressure 100 t stroke 500 mm table surface area 900 x 600 mm rapid traverse 22 mm/s Hjdjvprv Rjpfx Abkenu stroke speed 2 mm/s ram surface 700 x 350 mm total power requirement 2,2 kW weight of the machine ca. 1,6 t dimensions of the machine ca. 1,9 x 0,85 x 2,3 m The machine is of the Italian make SICMI, which was traded by the Knuth company.

Condition: used, Year of construction: 1964, Technical details: pressure: 125 t stroke: 28 mm number of strokes: 56-225 Hub / Min distance between columns: 1000 mm ram adjustment: 60 mm distance table/ram: 376 mm Table dimensions: B.950xT:720 mm passage opening in table: 400x130 mm height over floor: 1120 mm ram surface area: 920x540 mm mortise hole in ram: Dm 65 x 120 mm column travel -side: 250 mm total power requirement: 30 kW weight of the machine ca.: 15,5 t dimensions of machine: 3,1x1,34x3,6 m dimensions electric cabinet LxWxH: 0,64x0,22x1,2 m This press is a high-performance press for mass production /series production. - Contains left side a material feed via automatic feed (mechanic) and right side a waste cutter. Feed = 0-200mm, roll width =250mm Partial documentation as a copy available. Machine is not functional and is on sale as is! * Hsdpsu Nfibefx Abkjnu

Condition: used, Year of construction: 1980, spindle diameter 135 mm Hedpfoy Ehwhjx Abkenu x-travel 950 mm distance between columns 1100 mm y-travel 700 mm cross rail adjustment - vertical 780 mm quill travel 300 mm max. distance between table and spindle-nose 1000 mm table surface area 1100x842 mm table load 1500 kg speeds 40-2000 U/min adjustment speed 5-1500 mm/min electrics - voltage/frequency 380/50 V/Hz total power requirement 8 kW weight of the machine ca. 9,5 t dimensions of the machine ca. 3,3x2,34x2,8 m total power requirement 8 kW weight of the machine ca. 9,5 t dimensions of the machine ca. 3,3x2,34x2,8 m

Condition: used, Year of construction: 1984, pressure 500 t Hnjdot Hwpyepfx Abkou passage width 750 mm stroke 120 mm total power requirement 57 kW weight of the machine ca. 16 t dimensions of the machine ca. m

Condition: used, Year of construction: 2005, Pressure 600 t distance between columns 2600 mm stroke 900 mm Distance table/ram, max. stroke up, adjustment up 1600 mm Table surface area 2500 x 1730 mm pressure of drawing cushion in table 250 t Die cushion stroke in table 400 mm Die cushion area in table 2300 x 1300 mm Die cushion pressure in ram 63 t Hnsdpfxezrptzs Abksu Die cushion stroke in ram 160 mm Die cushion area in ram 1900 x 1300 mm Ram surface 2500 x 1730 mm Side window 1100 mm Oil volume 3500 l Power capacity 200,0 kW Dimensions (WxDxH) 4,1 x 2,8 x 9,6 m Height above floor 6,4 m year of manufacture 1974 - overhaul 2005: complete new electrical cabinet with control Siemens S7 and safety control Pilz with oil-hydraulic drive, hydraulic controlled drawing cushion in table and ram, hydraulic cutting impact cushioning stored in dismantled condition - Video at seller’s site before dismantling available

Condition: used, pressure 100 t distance between columns 310 mm no. of strokes 80 Hub/min Hsdpfx Abelp U Sdokonu ram - range of adjustment 40 mm table surface area 400x300 mm ram surface 250x190 mm table height 960 mm tool hole in ram Ø 35 mm weight of the machine ca. 1,5 t dimensions of the machine ca. BxTxH 1500x1500x2200 m

Condition: used, Year of construction: 1996, functionality: limited functionality, CNC-Planer-Type Milling M/C - Double Column (Milling and Turning Center) | Brand: DÖRRIES SCHARMANN | Type: 4FZT | Year of construction: 1996 A high-performance gantry milling machine designed for machining large workpieces. Its primary applications include the milling and turning of large, complex workpieces. The machine can be inspected under power by appointment. Condition: Consistent with the year of manufacture; some parts require refurbishment. - A high-quality machine, and therefore well worth modernization / a complete overhaul / highly recommended. TECHNICAL SPECIFICATIONS: Main Dimensions: - Machine width: 13.230 mm - Machine height over the floor: 8.450 mm - Machine length: 31.100 mm - Working length: 11.000 mm Hsdpfjyuptzox Abkonu - Clearance width: 4.400 mm - Clearance height from the table surface to the spindle nose of the standard milling head: 3.000 mm Table: - Table width: 3.450 mm - Total table length: 13.400 mm - Length of individual table: 6.200 mm - Total clamping area: 3.450 x 11.000 mm - Clamping area of single table: 3.450 x 5.000 mm - Maximum total workpiece weight: 112 tons - Maximum workpiece weight per table: 80 tons Crossbeam: - Travel: 2.000 mm Milling and boring support: - Drive power for milling and boring (spindle): 80 kW - Max. speed of the drive shaft (spindle): 2.500 rpm EQUIPMENT / ACCESSORIES: - 2 tables - 8 machining heads - Control: SINUMERIK 880 - 2 x chip conveyors - Documentation - CE marking No guarantee for completeness and accuracy of technical data and equipment. - Subject to prior sale - Detailed technical data sheet and information on equipment available on request.

Condition: used, Year of construction: 1990, pressure 3 t throat 0 mm stroke 200 mm total power requirement 15 kW weight of the machine ca. 4 t dimensions of the machine ca. m Fully Automatically Straightening Press, 3 Stations,parts turning, (bolts) Hjdpet Hw Amsfx Abkjnu

Year of construction: 1978, condition: used, pressure 2000 /1000* t distance between columns 2650 mm stroke 500 mm column travel -side 500 x 1000 mm diameter of piston 710 mm number of pistons 2 distance between table / ram 1000 mm operating pressure 130 / 230 bar dayligth 800 mm table length 2500 mm table width 1600 mm table height 250 mm draw back pressure 500 kN number of T-slots 8 turning speeds 1500 U/min rapid speed 120 - 140 mm/min closing speed max. 120 - 140 mm/sec. return of plunger by small single cylinders 100 - 110 mm/sec hydraulical ram locking cutting sound absorber 300 t die cushion capacity 200 t Hnjdpfxod Ih Nce Abksu die cushion stroke 250 mm speed of die cushion 100 mm/sec frequency 50 Hz voltage 380 V quantity of oil 2000 l total power requirement 93 kW weight of the machine ca. 100 t dimensions of the machine ca. 5000 x 2500 x 7200 mm transport measurements ca. 6500 x 3750 x 2190 mm 1991 assembly of a die cushion, pressure reduction to 1000 tons reason: tools were only constructed to 1000 tons press has run in a perfect condition until disassembly. It was replaced by a press line. important for UVV: press has a hydraulic ram locking!

Year of construction: 1986, condition: used, pressure 015 t dayligth - mm Hnedpfx Aofn Apxebksu strokes per minute 200 - 2000 table surface area - mm ram surface 490 x 200 mm sheet width 5 - 50 mm adjustment of stroke 10-30 mm weight 3 t dimensions 1370 x 1200 x 2200 mm Drive 10 kW hole in the table 350 x 100 mm table width 530 / 210 mm table length 530 / 350 mm

Condition: used, Year of construction: 1993, machine/vehicle number: 493187, Lg. No. 21236 Hydraulic - twin-column guided miter - metal band saw Technical Data: Hnedpfx Ajwqpmnebkou - Cutting range at 90° Round 360 mm - Rectangle 600 x 360 mm - Cutting range at 45° Round 320 mm - Miter adjustment via handwheel - Saw band size 5400 x 38 x 1.3 mm - Cutting speed steplessly adjustable 19 - 130 m/min - Cutting pressure steplessly adjustable 0 - 10 m/min - Manual material clamping - Pre-selection of the stroke height of the saw band - Micro-spray coolant system - Total drive power 400 V / 8 kW - Space requirement ca. W 1800 x H 2000 x D 3250 mm - Weight approx. 2200 kg - Infeed + outfeed roller conveyors each approx. 6000 / 8000 mm

Condition: used, Year of construction: 2010, pressure 600 t distance between columns 3640 mm stroke fix 350 mm no. of strokes 11 - 44 /min dayligth (stroke and adjustment up) 1550 mm column travel -side 2200 mm table surface area 3600 x 2500 mm ram surface 3600 x 2500 mm ram adjustment 400 mm band width 2000 mm material thickness 0,6 - 2,5 mm material cross-cut 1600 x 2,5 mm² coil weight 35,0 t Number of Straightening rolls 13 0 Hnsdpjzrppcofx Abksu straightening roll diameter 50 mm Blanking Line (press, coil line, blank stacking system) yom 1993 - 2010: new control Siemens S 7 - press Schuler type EBS 4-600 with infinitely variable drive, fly-wheel brake, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, ram interlocking moving tables (2x) without rails for the moving tables - decoiler make Schleicher, type HE - 355 - 2100, yom 1994 with auxiliary drive, snubber roll - coil lifting device - extractor device make Schleicher - shear - straightening machine make Schnutz, type RME 18/50/13-2000 TZ, yom 1994 with infinitely variable drive, 30 intermediate rolls, 117 supporting rolls - coil loop bridge - roll feed make Schleicher, type WV-SYS-A 160-2000, yom 1994 - blank stacker NSM-Magnettechnik stored in dismantled condition - Video before dismantling available

Year of construction: 1978, condition: used, pressure 40 t Hjdoq Rhkwjpfx Abkjnu distance between columns 600 mm stroke 150 mm table surface area 600x410 mm ram surface 220x130 mm table height 850 mm weight of the machine ca. 2,5 t

Condition: used, Year of construction: 1985, pressure 63 t passage width 1350 mm stroke 300 mm Hedst Hwxuepfx Abkonu total power requirement 16 kW weight of the machine ca. 10 t dimensions of the machine ca. 2,0 x 1,8 x 3,4 m

Condition: new, pressure 300 t working feed 3-8 mm/sec stroke 500 mm return speed 15 mm/sec table-size 3000 x 1500 mm tank capacity 45 l Hnedpovxw Hmsfx Abkou travel x / y 2600 x 1000 mm daylight 500 mm total power requirement 18,5 kW weight of the machine ca. 18 t

Condition: used, Technical details: pressure: 20 t slide stroke: 6 - 60 mm throat: 176 mm ram adjustment: 55 mm no. of strokes: 155 Hub/min distance table/ram: 270 mm passage width: 470 mm Table dimensions: 300 x 450 mm passage opening in table: 90 mm surface area of ram: 130 x 248 mm inclination: 28 ° mortise hole in ram: 25 x 65 mm table height over floor: 775 mm air pressure - required: 5,5 - 6 bar total power requirement: 3,5 kW Hnodpsu Nflisfx Abkeu weight of the machine ca.: 1,0 t dimension machine approx.LxWxH: 1,3 x 1,1 x 1,95 m High performance press Central lubrication with light barrier (monitored) Linuflex stroke counter (counter) additional steel plate 315 x 400 x 50mm with center hole Ø 63mm *

Condition: used, Year of construction: 1990, Technical details: Pressure: 63 t distance between columns: 200 mm stroke: 150 mm dayligth: 430 mm no. of strokes: 400 Hub/min T-slots H 12 650: 18 mm hole in table: 420x160 b x l mm ram surface area: 650 x 450 mm control: Wanske Tronicpress CNC passage of columns: 550x540 mm tank: 200 l stroke of ram - fixed: 100 mm ram diameter: 40 mm table height over floor: 1000 mm table: 600x450 mm table height over floor with metal base stand: 880 mm total power requirement: 30 kW weight of the machine ca.: 3,9 t Hydraulic automatic punching press for precision work (high-speed press) - for punching, drawing, pressing, minting, bending, riveting, straightening, assembling - with hydraulic gripper feed type HS 150 and 7-roller straightener (moving) - Normal strips of approx. 0.4mm - 2.5mm thickness x approx. 160mm width, as well as narrow strips up to approx. 4mm can be processed. Feed length can be adjusted as required via the control unit. - with ram round column guide - with automatic central lubrication - High-speed: up to 400 strokes min-1 - motorized adjustable fixed stop (bottom can be adjusted by hand/motorized) Hnedeu Icxqepfx Abkju - Operating modes such as continuous stroke and/or single stroke Equipment: - 1x hydraulic unit - 2x control cabinets *

Condition: used, Technical details: faceplate diameter: 4000 mm swing diameter: 4300 mm turning height: 330 mm faceplate turning speed range: 1 - 92 U/min workpiece weight: 18 t feeds: 1 - 4000 mm/min main drive motor: 55 kW total power requirement: 85 kVA Hjdpfx Aevb Dq Rebkjnu weight of the machine ca.: 64 t dimensions of the machine ca.: 90, x 7,2 x 5,5 m with CNC SIEMENS 840 D for 4 axis 2 Vertical Supports tool Basic holder chip conveyor *

Condition: excellent (used), Year of construction: 1994, operating hours: 1,930 h, functionality: fully functional, travel distance X-axis: 7,200 mm, travel distance Y-axis: 4,200 mm, travel distance Z-axis: 1,750 mm, feed rate X-axis: 15,000 m/min, feed rate Y-axis: 15,000 m/min, feed rate Z-axis: 15,000 m/min, total length: 15,000 mm, table length: 5,000 mm, total width: 15,000 mm, spindle speed (min.): 10 rpm, spindle speed (max.): 4,000 rpm, total height: 7,500 mm, table height: 1,350 mm, distance between stands: 3,500 mm, type of input current: AC, table load: 65,000 kg, workpiece weight (max.): 65,000 kg, distance table center to spindle nose: 2,300 mm, overall weight: 210,000 kg, spindle motor power: 50,000 W, MACHINE DATA Machine type: Portal milling machine - double column for continuous 5 axis operation Manufacturer: WALDRICH COBURG Model: 15 S - 10 FPF 300 NC Year of construction: 1994 Condition: Fully refurbished 2015 Functionality: fully functional Operating hours: 2,931 h TECHNICAL DETAILS Number of controlled axes: 5 travel distance X-axis: 7,200 mm travel distance Y-axis: 4,200 mm travel distance Z-axis: 1,750 mm spindle speed (max.): 4,000 rpm working width: 3,500 mm PROVISION Machine location: Ljubljana, Slovenia Availability: now Delivery conditions: FCA Pick up at location: Ljubljana Shipping costs: upon request Planer-milling machine - double column: completely overhauled in 2014 / 2015 by Waldrich Coburg (basically everything except the casting): > New control unit > New cables > New motors > New electrics > Guideways overhauled DESCRIPTION - Heavy double-column machine for processing complex shapes - 2 pallet stations with 2 pallets (load capacity 65t each) - Machine with CNC control SIEMENS 840D sl - In 2014, conversion of the control system to SIEMENS 840D sl (incl. complete cabling and control cabinet) - in 2015 replacement of all axis motors - Various angle milling heads - NC-controlled milling head with 50 kW milling power / clamping 2.5° each with Hirth serration (type USP300C450F15S) - 2-axis NC-controlled fork head with 40 kW milling power (type UFN00SZ500) - Automatic tool changer for 76 tools (ISO 50 and 60) TECHNICAL DETAILS Travel X / Y / Z: 7,200 / 4,200 / 1,750 mm Milling width: 3,500 mm Distance spindle nose to table: 2,300 mm Milling power: 50 kW Speed: 10 - 4,000 rpm Front spindle diameter: 150 mm Spindle holder: ISO 60, ISO50 Control: Siemens 840D sl Pallet size: 3,000 x 5,000 mm Pallet load: max. 65 t Number of pallets: 2 pieces Tool changer: 76 slots Feed rate: 10 - 15,000 mm/min MACHINE DETAILS Pick-up power: 92 kW Weight: 210 t Spindle hours: 2,931 h Switch-on time: 10,870 h Bed dimensions: 12.5 x 2.3 x 0.78 m; 28.5 t Pallet dimensions: 5.35 x 3.0 x 0.4 m; 22 t Main pallet carrier dimensions: 5.1 x 2.9 x 0.5 m; 25 t Dimensions of bed section: 3.8 x 2.9 x 0.5 m; 10 t Milling spindle box dimensions: 4.1 x 1.9 x 1.5 m; 13.5 t Left/right column dimensions: 4.1 x 1.3 x 1.7 m; 10.5 t Exhaust air slide dimensions: 8.5 x 0.7 x 1.2 m; 1.1 t Control cabinet dimensions: 7.9 x 0.6 x 2.1 m; 2.8t Hnsdpsvv N I Rsfx Abkeu THIS IS A TOP CLASS MACHINE FOR MOST ACCURATE WORK; HIGHLY EFFECTIVE. MACHINE IS ASSEMBLED AND UNDER POWER: