Used Belt Sanding Machine Holzkraft Lbsm 2505 -Used- for sale (94,097)

Year of construction: 2009, condition: excellent (used), I sell the widebelt sanding machine RWT BS950RP, year 2009. Configuration: Hard rubber cylinder Combi unit soft rubber cylinder + pneumatic jumping pad. Working width 950mm Elektronic working height adjustment with digital readout 3-160mm 1 Motor 11kW 2 Feeding speeds. Programming of in/out jump of the pad. Sensitive adjustment of pad position. Sensitive adjustment of cylinders position. Pneumatic adjustment of pad and cylinders pressure position. Pressure rollers for short elements. Condition LIKE NEW ! The machine was working only a few. Available immediately. Ibjdeiuc Sgepfx Afusc

Condition: not inspected (used), Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine Ibjdpfx Afst Tqy Esujc machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: used, Year of construction: 1997, functionality: fully functional, machine/vehicle number: 02/96088A, total length: 7,500 mm, total width: 2,000 mm, total height: 2,000 mm, overall weight: 7,500 kg, Edge grinding machine with 10 programmable profiles, including rounded edges Pre-milling cutter 10 face milling operations 4 chamfering operations 2 water break grooves Calibration support Belt feed direction from left to right Deburring cutter Ibodpfszpy Drex Afuec Unit for water break grooves from above and below Can grind 9 profiles – e.g., bullnose, full round, half round, small rounding on the top and bottom, chamfered, quarter round.

Year of construction: 2014, condition: used, Number of sanding units 6 St. sanding width 180 mm Sanding height max. 150 mm STAEHLE Grinding Machine Type Gloria/Saturn E 180 RF ----- Stähle Hess Finish Grinding Machine Type Saturn E 180 RF (formerly Gloria) with 2 grinding units, plus top and bottom Roto Finish grinding attachments. 1 upper grinding belt 1 lower grinding belt 2 upper Roto Finish grinding attachments 2 lower Roto Finish grinding attachments For a detailed description, please see the accompanying PDF from the manufacturer. Sold on behalf of a customer. The images are from our archive and were taken before the machine was delivered to the customer. Isdpsx Dng Djfx Afujbc (Technical specifications according to the manufacturer - without guarantee!)

Condition: excellent (used), Year of construction: 1997, I sell the widebelt sanding machine Tagliabue TA G-13-KS-DX 1350, year 1997. Configuration: 1pc. rubber cylinder 1pc electronic segmented pad Cleaning unit combined brush + air blow in the outfeed. Working width 1350mm Pressure shoes for short elements. Air-blow on all units. Vacuum underpressure table with integrated ventilator. Iodpfx Afjyzrpmouebc Designed for the line, with fixed working height and moving aggregates. 2 motors total power 40kW Condition very good ! Available immediately.

Condition: used, Year of construction: 2007, functionality: fully functional, machine/vehicle number: 2MAZL000283, power of the servo motor: 350 W, input voltage: 230 V, clearance between the columns: 70 mm, type of input current: AC, throat depth: 120 mm, feed length X-axis: 22 mm, feed length Y-axis: 78 mm, feed length Z-axis: 10 mm, pneumatic connection: 6 bar, JUKI MOL-254 – Automatic Belt Loop Attaching Machine High-Speed Denim Production Unit – Video Verified (03/2026) Description For sale is a JUKI MOL-254 automatic belt loop attaching machine, designed for fully automated production of belt loops in jeans, trousers and workwear. This is a specialized high-speed production unit, not a standard sewing machine. The machine automatically feeds, cuts, positions and bartacks belt loops with consistent precision and strength. The unit has been used in a professional garment production environment and is offered as a complete industrial workstation. Video recorded in operation on 05.03.2026 Serviced on 27.02.2026 Production-ready condition Production performance Cycle time approx. 1.2 seconds per loop Up to 2,000–2,500 belt loops per shift Simultaneous top and bottom bartacking Consistent symmetry and reinforcement quality Key features Isdpfx Afoy Nd Hgsuebc Fully automatic belt loop feeding, cutting and attaching Integrated bartack stitching system Pneumatic material handling system Digital JUKI control panel Adjustable loop size settings Stable performance on heavy fabrics such as denim and workwear Designed for continuous industrial use Includes JUKI MOL-254 machine unit Integrated motor and drive system Pneumatic system Industrial table and stand Operator control panel Thread stand Technical details Manufacturer: JUKI, Japan Model: MOL-254 Type: Automatic belt loop attaching machine Control: Electronic JUKI control system Drive: Industrial motor with pneumatic system Application: Belt loop production Condition Used industrial production condition Fully functional Serviced 27.02.2026 Video proof available Typical signs of use from factory environment Sold as-is, where-is, without warranty Applications Jeans manufacturing Workwear production Trousers production Automated garment production lines Location Valga, Estonia Logistics Buyer responsible for dismantling and transport

Condition: excellent (used), Year of construction: 1997, I sell the widebelt sanding machine Tagliabue TA G T12-KS-SIN 1350, year 1997. Configuration: 1pc. rubber cylinder 1pc. electronic segmented pad 1pc. cross band Cleaning unit combined brush + air blow in the outfeed. Iodpfeyzrqqsx Afuebc Working width 1350mm Pressure shoes for short elements. Air-blow on all units. Vacuum underpressure table with integrated ventilator. Designed for the line, with fixed working height and moving aggregates. 3 motors total power 55kW Condition very good ! Available immediately.

Condition: new, Number of sanding units 4 St. sanding width 190 mm Sanding height max. 180 mm LÖWER-DoubleSander Solid DSM 2004 ----- Double-sided four-belt single wood sander for Sanding solid wood such as window frames etc. Highly stable top design with innovative details. Suitable for high continuous loads even with higher chip removals. - sanding units arranged one after the other for pre-grinding, Fine sanding and finishing sanding, each from above and below 1. Belt sanding unit with heavy steel roller 2. Belt sanding unit with rubberized roller and shoe 3. Finishing unit with fiber brush - Directly driven grinding rollers for slip-free Power transmission - maintenance and wear-free CERMET-coated grinding wheels shoes with very good thermal conductivity and absolute Ibedovnv Tqopfx Afuoc Dimensional accuracy - External cooling of the grinding zones for cooler grinding and longer sanding belt service life - force-guided pneumatically controlled sanding belt oscillation - effective sanding dust extraction directly on the Grinding rollers - Airborne dust extraction on the tension rollers - Integrated brushing and finishing device with large Grinding dust extraction - motorized grinding thickness adjustment via precision threaded spindles and large-sized linear ball screws bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of the chip removal at the bottom via precision Threaded spindle with dimension display via scale ring (Resolution 0.1mm) - Sanding belt tension via pneumatic cylinder constant clamping pressure - Sanding belt change with pneumatic belt relaxation Within seconds - Adjustment option for the sanding belt run Band change - electro-pneumatic compressed air monitoring - Anti-running protection via contact roller if it is too thick workpieces - Workpiece transport via calibrated non-slip and non-stick fixed conveyor belts over heavy, cast tables Finely planed surface and spring-loaded pressure rollers with fine adjustment - Cardan shaft drive for smooth and consistent Workpiece transport - Feed gear motor with stepless speed 4-20 m/min - all motors electrically protected - ergonomically arranged controls - digital thickness display (resolution 0.1mm) with modern Magnetic tape system Technical data: - Sanding belt speed 22 m/s - Sanding belt length 1800mm - Sanding belt width 200mm - Working width 190mm - Grinding thickness 2-180mm - four brake motors for 5.5 kW drive - Feed motor 1.5 kW - Feed speed 4-20 m/min. - automatic height adjustment 0.37 kW - two brush units with fiber brushes D 120 x 200mm at 0.37 kW - Suction nozzle 2 x 180mm 2 x 120mm - Extraction air speed 20 m/s - Pneumatic connection 6 bar - Working height 870mm - Length (with soft disc 2740mm) 2600mm - Length with control panel (with soft disc 3035mm) 2985mm - Width 880mm - Height 1910mm - Weight approx. 3300 kg - Operating voltage 400 volts, 50 Hz, 3P - CE version ----- Price of the above machine on request! ----- Special accessories with additional charge: Workpiece blow-off - using nozzles from above and below at the machine outlet arranged, pneumatically controlled 4-belt sanding belt blowout via nozzles directly on the radii of the tension rollers inside the suction arranged, timer controlled on/off 5 seconds each, can be switched on separately Di...

Condition: used, Year of construction: 2006, incl. 2nd sanding padused, top equipmentmake SCM Samcotype EG 2500year of manufacture 2006machine . AM/28506motor 3.0 / 2.2 kWsanding length approx. 2500 mmsanding width approx. 1000 mmbelt length approx. 6800 mmtable size approx. 2500 mm x 1000 mmcranking right approx. 700 mmcranking left approx. 700 mmelectric adjustmentupper belt coverupper sanding supportbelt speeds 1400 /2800 rpm = 23 m/sec /46 m/secright-left runsuction connection D 160 mmspace requirement approx. 3900 mm x 1700 mm x 1500 mmtotal connected load approx. 4.55 kWstorage location 97447 Gerolzhofen, free loaded, unpackedhandover in as-is condition as inspected,without guarantee and warranty Ibsdpfxovwffbe Afuoc

Condition: new, Panel saw VPS 22-51 VR ED KS Holzkraft -Exhibition machine- -----Technical data----- Cutting length: 5100 mm, Ijdpjwnrf Usfx Afujbc Cutting height: 2200 mm, Cutting depth: 60 mm, Saw blade diameter: 250 mm, Motor: 3 kW, Dust extraction port diameter: 100 mm, Space requirement (L x W x H): 6300 x 1800 x 3200 mm - Clamping force of clamping system: 250 kg Dust extraction connection: - Dust extraction port diameter: 100 mm - Minimum air flow for dust extraction: 1800 m³/h - Minimum air velocity: 20 m/s Equipment: - Lower material support: metal rollers - Adjustable slat bed: automatic - Vertical dimension display: digital - Horizontal dimension display: digital - Panel clamping system - Locking of the saw carriage: pneumatic Electrical data: - Power of drive motor: 3 kW - Connection voltage: 400 V - Mains frequency: 50 Hz - New exhibition machine -

Condition: new, Year of construction: 2022, I sell the new widebelt sanding machine Casadei Libra 45 RCT 110 Year 2022. Configuration: Steel moulding cylinder with spiral knives Combi unit hard rubber cylinder + segmented pneumatic jumping pad. Working width 1100mm Elektronic working height adjustment with digital readout 3-160mm 1 Motor 2 Feeding speeds. Programming of in/out jump of the pad. Ibjdpfx Aferddh Ieujc Sensitive adjustment of pad position. Sensitive adjustment of cylinders position. Pneumatic adjustment of pad and cylinders pressure position. Pressure rollers for short elements. Air-blow for cleaning the sanding band. Condition NEW ! The machine was not working before. Available immediately. Including full documentation and CE.

Condition: excellent (used), Year of construction: 2023, width of the strips 75.0 mm band length 2000 mm band speed 30.0 m/sek grinding width 500 Plantisch mm suction capacity 630 m³/h total power requirement 3.75 kW weight of the machine ca. 90.0 kg range L-W-H 1100 x 550 x 1035 mm current new price incl. accessories approx. 2.500 euros incl. replacement sanding belts special price on request Equipment : - High quality construction - Drive roller is crowned - This means that the sanding belt is automatically centered on the roller - Fully vulcanized contact roller for maximum service life and smooth running - Tool-free and therefore quick, uncomplicated change of the sanding belt - Stepless height adjustment - for optimum adjustment of the belt sander to the user - Freely adjustable metal fence - for optimum and safe guidance of workpieces when Use of the large surface sanding area - Belt speed optimized by design - to prevent the workpiece from burning during processing can be excluded as far as possible - Suction unit equipped with robust and flexible suction hoses - Motor protection switch with CEE collar connector incl. phase inverter - Motor brake - Incl. sanding belt grain 60 Ibedsy Erxvepfx Afuoc - Dust bag

Condition: new, Year of construction: 2024, Working width: 950 mm Workpiece height min: 4 mm Workpiece height max: 170 mm Height adjustment: electronic Workpiece thickness display: digital Control unit: Fox 500 KTR Units: 1 1st unit: Combination unit for calibrating and sanding / Bevel-grooved steel roller, Ø 120 mm, with fine height adjustment / Hard sanding shoe with graphite support Dust removal brush: no Ibsdeknyhlspfx Afuec Motor power: 7.5 kW Dust extraction connection: 140 mm Machine length: 1388 mm Machine width: 1545 mm Machine height: 1668 mm Weight: 660 kg

Condition: used, Year of construction: 2017, - 4 belt grinding units - Frequency control for all units - Electronic grinding pressure control Universal edge and profile grinding machine Manufacturer: Heesemann Type: UKP 20 Year of manufacture: 2017 Technical data Workpiece transport system - Total length: 5015 mm - Driven by a 1.5 kW three-phase motor with a double chain for workpiece transport - Feed rate in the range of 5-25 m/min, frequency-controlled - Working height constant at 880 mm - incl. integrated control cabinets - incl. adjustable guide rail with digital display and incl. counter rail with central width adjustment Ibsdpfozuzb Asx Afuoc 4 lateral guide rollers between the grinding units for secure transport of workpieces Industrial PC 10.4" - LCD-TFT color display - Touch screen version - with display for production and downtime - with program memory for 100 programs 2 belt grinding units "M 4" Pos. 1 and 2 - for grinding straight edges - Belt dimensions: 2300x80 mm - Belt speed: 0.7-12 m/s - Motor power: 3.0 kW - with electronic frequency control for stepless control of the belt speed - Electronic grinding pressure control from the terminal 2 oscillation units for "M4" (Pos. 1+2) For complete utilization of the grinding belt 2 belt grinding units "K 4" Pos. 3 and 4 - for grinding small profile sections - can also be used for edge breaking - Can be swiveled 90 degrees upwards and 45 degrees downwards - Belt tear switch - Tool holder with quick-change device - Intermittent belt extraction device - Belt dimension: 2000x50 mm - Belt speed: 0.5-8 m/s - Motor power: 1.1 kW - with electronic frequency control for stepless control of the belt speed - Electronic grinding pressure control from the terminal 4 electronic control units - for the fully automatic timing of the lowering and raising of the grinding tool, depending on the set feed rate, the grinding pressure and the unit angle setting Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: new, Hoku KS 150 edge sander manufactured by Rehnen. The upper section is made of heavy-duty cast iron with a built-in three-phase motor 380 V, 2.2 kW, 2850 rpm; the machine is equipped with a built-in switch-plug combination; Ibjdpfx Aswgc D Sofusc Motor protection switch and main switch in accordance with VDE regulations; Sanding belt back panel dimensions: 850 x 150 mm; steel table height adjustable by spring pressure; belt dimensions: 150 x 2280 mm; The sanding belt back panel is covered with a graphite sliding coating; The machine is supplied with an assortment of sanding belts; A square and miter gauge is also included. The machine is dust-tested (GS) by Holz-BG-Stuttgart when connected to a central extraction system with an air speed of at least 20 m/s. - Swivels 90-180° - Motorized belt oscillation - Small support table on the idler pulley - Pneumatic belt tensioning Technical specifications: Motor power: 2.2 kW Sanding belt dimensions: 150 x 2280 mm Sanding belt speed: 22 m/s Table size: 750 x 350 mm Space required: 1000 x 800 mm Weight: from 180 kg Extraction diameter: 100 mm

Condition: new, Number of sanding units 2 St. sanding width 290 mm Sanding height max. 180 mm LÖWER-DoubleSander Solid DSM 3000 ----- Two-sided single wood sander for sanding Solid wood such as window wood etc. Stable Top version with long casting tables, brushing and finishing device and conveyor belt feed. Suitable for high Permanent load even with higher chip removals. - Staggered sanding and finishing units at the top and below - directly driven rubberized sanding rollers for slip-proof free power transmission - Combined grinding via roller and shoe for high chip removal with a flat intervention zone at the same time - maintenance and wear-free CERMET-coated grinding wheels shoes with very good thermal conductivity and absolute Dimensional accuracy - External cooling of the grinding zones for cooler grinding and longer sanding belt service life - force-guided pneumatically controlled sanding belt oscillation - effective sanding dust extraction directly on the Grinding rollers - Airborne dust extraction on the tension rollers - Integrated brushing and finishing device with large Grinding dust extraction - motorized grinding thickness adjustment via precision threaded spindles and large-sized linear ball screws bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of the chip removal at the bottom via precision Threaded spindle with dimension display via scale ring (Resolution 0.1mm) - Sanding belt tension via pneumatic cylinder constant clamping pressure - Sanding belt change with pneumatic belt relaxation Within seconds - Adjustment option for the sanding belt run Band change - electro-pneumatic compressed air monitoring - Anti-running protection via contact roller if it is too thick workpieces - Workpiece transport via calibrated non-slip and non-stick fixed conveyor belts over heavy, 1000mm long cast iron tables with a finely planed surface and spring-loaded Pressure rollers with fine adjustment - Cardan shaft drive for smooth and consistent Workpiece transport - Feed gear motor infinitely variable for quick adaptation to different types of wood - all motors electrically protected - Ergonomically arranged controls on the workpiece inlet side - digital thickness display (resolution 0.1mm) with modern Magnetic tape system Technical data: - Sanding belt speed 22 m/s - Sanding belt length 1800mm - Sanding belt width 300mm - Working width 290mm - Grinding thickness 2-180mm - two brake motors for 7.5 kW drive - Feed motor 1.0 kW - Feed speed 4-20 m/min. - automatic height adjustment 0.37 kW - two brush units of 0.37 kW each with fiber brushes D 120 x 300mm - Suction nozzles 2 x 120mm and 2 x 150mm - Pneumatic connection 6 bar - Working height 850mm - Length 2105mm - Length with control panel 2490mm - Width 980mm - Height 1910mm - Weight approx. 1650 kg - Operating voltage 400 volts, 50 Hz, 3P - CE version ----- Price of the above machine on request! ----- Special accessories with additional costs: Ijdpfxoyrty To Afuobc Workpiece blow-off - using nozzles from above and below at the machine outlet arranged, pneumatically controlled Sanding belt blowout via nozzles directly on the radii of the tension rollers inside the suction arranged, timer controlled on/off 5 seconds each, can be switched on separately Disc unit for defibering - two gr...

Condition: new, width of the strips 75.0 mm band length 2000 mm band speed 30.0 m/sek grinding width 500 Plantisch mm suction capacity 630 m³/h total power requirement 3.75 kW weight of the machine ca. 90.0 kg range L-W-H 1100 x 550 x 1035 mm Furnishing : - High quality construction - The drive roller is crowned - This automatically centers the sanding belt in the middle of the roll - Fully vulcanized contact roller for the longest service life and the best possible smoothness - Tool-free and therefore faster, uncomplicated change of the sanding belt - Stepless height adjustment - for optimal adjustment of the belt sander to the user - Freely adjustable metal stop Ibjdpfx Asxabtcofuec - for the optimal and safe guidance of workpieces Use of the large surface grinding area - Belt speed structurally optimized - thus a burning of the workpiece during processing can be largely excluded - Extraction equipped with robust and flexible suction hoses - Motor protection switch with CEE collar connector including phase inverter - engine brake - Including sanding belt, grain 60 - dust bag

Condition: new, width of the strips 150 mm band length 2000 mm band speed 30.0 m/sek grinding width 500 Plantisch mm suction capacity 630 m³/h total power requirement 3.75 kW weight of the machine ca. 100 kg range L-W-H 1100 x 550 x 1035 mm Ibodpfxoxabhgs Afuec Furnishing : - High quality construction - The drive roller is crowned - this automatically centers the sanding belt in the middle of the roll - Fully vulcanized contact roller for longest service life and smooth running - Tool-free and therefore faster, uncomplicated change of the sanding belt - Stepless height adjustment - for optimal adjustment of the belt sander to the user - Freely adjustable metal stop - for the optimal and safe guidance of workpieces Use of the large surface grinding area - Belt speed optimized in terms of design - thus burning the workpiece during processing can be largely excluded - Extraction equipped with robust and flexible extraction hoses - Motor protection switch with CEE collar connector including phase inverter - engine brake - Including sanding belt, grain 60 - dust bag

Condition: used, Year of construction: 2010, - Perfect for surface finishing - Constant working height - Q/L/Q Fine/cross-sanding machine Manufacturer: Weber Type: KSF-3-1350 Year of manufacture: 2010 Technical data - Equipped with 3 sanding belts for high-quality fine, veneer, and high-gloss sanding. - With a constant working height Machine frame - Heavy-duty steel welded construction for mounting 3 sanding units - Constant inlet height of 900 mm - Control and sanding belt change side on the inlet side, on the left - Stepless feed speed of 3-18 m/min, frequency-controlled. - Vacuum version of the conveyor belt / with 1 vacuum blower 5.5 kW, and a vacuum channel up to the upper edge of the machine Unit 1: Cross-belt unit - Pressure pad belt with felt and graphite for long service life - ISD segmented pressure bar system with 11 mm workpiece detection and 44 mm pressure pad width - Workpiece-controlled sanding belt blowing device Unit 2: CBF combination unit - One grooved rubber contact roller 0 130 mm, rubber hardness 60 Shore - One cross-running flap band with separate drive 4.0 kw - ISA segmented pressure bar system with 11 mm workpiece detection and 22 mm pressure pad width (counter-rotating) - Workpiece-controlled oscillating sanding belt blowing device Unit 3: Cross-belt unit - ISD segmented pressure bar system with 11 mm workpiece detection and 44 mm pressure pad width - Workpiece-controlled sanding belt blowing device Operator terminal SIEMENS" MP 377 12" Multi-Panel - Graphical user guidance via 12" color display - Program memory with 300 programs - Setting of all parameters via program WEBER i-Touch control - One rotary knob for navigating through the most important functions WEBER AWDM - Automatic thickness adjustment at the machine inlet with start switch Overthickness - Selector switch at the machine inlet with the following functions: - Automatic lifting of the contact roller and the segmented pressure bars - Feed stop ISA/ISD control - High-resolution workpiece detection in a 22 mm grid - Free loading of complex part shapes - Multiple loading with a small lateral distance - Sanding intensity individually adjustable at all edges - Sanding pressure adjustable via program ISA segmented pressure bar system (Unit 2) - Pressure pad movable in the longitudinal and transverse direction ISD segmented pressure bar system (Unit 1+3) As ISA, but additionally with - Separate adjustable pressure for the edge area (higher or lower) - Optionally only on the outer edge or outer and inner edges - Longitudinal and transverse edges or only longitudinal edges can be adjusted Workpiece blowing device - with WEBER ES system - Energy-saving, workpiece-controlled workpiece cleaning with single slider control WANDRES-Micro-Cleaning (single brush version) - Power sword brush with integrated micro-humidification of the linear brush (for optimal paint dust removal) Technical data - Working width: 1350 mm - Drive Unit 1 (frequency-controlled-Eco-Drive): 15.0 kW - Drive Unit 2 (frequency-controlled-Eco-Drive): 20.0 kW - Drive Unit 3 (frequency-controlled-Eco-Drive): 15.0 kW Ibodpfezuzctjx Afuoc - Drive CBF: 3.0 kW - Drive vacuum blower: 5.5 kW - Drive feed (frequency-controlled): 3.0 kW - Drive height adjustment (frequency-controlled): 0.75 kW - Sanding belt speed (frequency-controlled): approx. 3-20 m/s - Sanding belt dimensions cross belts (W x L): 2x150x5100 mm - Sanding belt dimensions wide belt (W x L): 1370x2620 mm - Workpiece thickness (min./max.): 4-140 mm - Working height (constant): 900 mm - S

Condition: new, Year of construction: 2010, functionality: fully functional, PMF 465 CE We offer for sale a high-quality, professional band pressing machine (thermal laminator) from the German manufacturer PMF GmbH Maschinenfabrikation. The unit is brand new, never used (so-called NOS – New Old Stock), and is in perfect technical and visual condition, still placed on its original transport pallet. PMF machines are highly regarded in Western Europe for their uncompromising precision, durability, and highest quality, in accordance with the Made in Germany standards. Model 465 is widely used in the footwear industry (reinforcing and joining upper parts), in the leather goods industry, in the garment industry, and in the automotive industry. An automatic conveyor belt ensures smooth and consistent material feed in the working area. A digital microprocessor temperature controller (accurate thermal stabilization) is coupled with two independent timer programmers for precise setting of the pressing time and transport time. A pneumatic clamping system is activated by means of an ergonomic, two-button foot pedal. The machine is equipped with a side air preparation unit (regulator with pressure gauge). A spacious work table with four independent, contoured auxiliary shelves for the operator, facilitating the handling of large or complex parts (e.g., uppers, patterns). Complete protection of the hazardous area: front and rear covers made of plexiglass, a metal perforated cover for the heating unit, and an easily accessible emergency stop button. The unit has a full CE certificate. Price for the machine is negotiable. Transportation to the customer is possible. If you have any questions, please do not hesitate to contact us. Isdpfxoz Sxbmj Afuobc

Condition: used, Year of construction: 1995, Constant machine - combination station, dust brush - thickness measuring device - electronic segmented sanding pad MCS System Weber 32 mm - grooved steel calibrating roller - belt blow-off - vacuum conveyor belt. Sanding width: 1100 mm Drive: 15 kW Feed approx. 1.1 kW Height adjustment 0.25 kW Sanding belt dimensions: 1150 x 2500 mm Max. workpiece thickness: 150 mm Machine width: 1700 mm Machine length: 2000 mm Machine height: 2160 + 150 mm Machine weight: 1900 kg Constant working height: 850 mm Extraction connector: belt 180 mm / brush 120 mm Suction air volume: 0.74 m³/s Connected load: 23 kW Compressed air supply: 7 bar Feed speed: 3-15 m/min. Operating hours: 7000 h Location: Nattheim Ibjdjx Twcpspfx Afujc

Condition: good (used), Year of construction: 1979, Belt grinding machine, type T 8 E, including dust collection system, year of manufacture 1979, table size 2800 x 950 mm, belt dimensions: 7700 x 150 mm, working length: 2700 mm, 4 kW motor, with filter hose, weight approx. 600 kg. SUBJECT TO DIFFERENT VAT RATES Transportation possible for an extra charge! Iedszldyispfx Afujbc The machine will be inspected before sale. For used machines with a year of manufacture of 2009 or earlier, the warranty is excluded when sold to commercial customers. Technical data and equipment may vary. Errors, prior sale and changes reserved. All information without guarantee.

Condition: used, Year of construction: 2001, This machine is fitted with a new Siemens PLC and touch panel. Technical specifications: - Manufacturer: Unisanding - Model: 2.2.0. 0-30 Iodpjxtakmefx Afuebc - Working width: 1300 mm - Year of manufacture: 2001, retrofitted in 2025 - 2 rollers, flexibly adjustable from 0–30°, operating from above - Flex-Trim special brushes - Vacuum belt with vacuum motor - With glass panel on the operator side - Sanding motors: 2 × 2.2 kW with thermal cut-out - Feed motor: 1 × 1.5 kW with thermal cut-out - Vacuum motor: 1 × 5.5 kW - Roller height adjustment axis: 1 × 0.18 kW - Feed speed: 2–10 m/min, frequency-controlled - Brush speed: 50–350 rpm, frequency-controlled - Voltage: 3 x 400 V, 50 Hz - Electrical power rating: 15 kW - Fuse: 63 A - Exhaust air volume (vacuum): 3,000 m³/h - Dust extraction volume: 5,000 m³/h (to be provided by the customer) - Length: 2,170 mm - Width: 2,040 mm - Height: 2,030 mm - Weight including control cabinet: 2,220 kg - Colour: RAL 7035 light grey/black - Operating side: left/right - Brush replacement side: right - Explosion-proof version: No - Location: at the Blomberg warehouse

Condition: ready for operation (used), Indumasch Siegen 362 Grinding Pedestal Belt Grinding Machine Grinder -Belt width: 150 mm -Speed: 1400 / 2800 rpm 220V / 380V -Extraction unit You are welcome to arrange an inspection appointment. We can also organize cost-effective shipping for you! You will receive a proper invoice. For international customers, a net invoice can be issued, provided a valid VAT ID number is supplied. Subject to prior sale. Visit our shop to see our other offers. Iodpfx Aeyyn A Hsfuobc All company names and trademarks mentioned are the property of their respective owners and are used for identification and product description purposes only. Deviations in technical data or errors in the item description may occur and are reserved.

Condition: new, Year of construction: 2026, CORMAK PSM200 – Industrial Mobile Belt Grinder for Metal The CORMAK PSM200 is an industrial-grade mobile belt grinder for metal, designed for intensive grinding, deburring, and polishing of large surfaces, weld seams, and workpieces that are difficult to process on stationary machines. Thanks to its integrated dust extraction system and compact design, it enables efficient operation in changing workshop conditions and directly on assembly sites. Main Advantages Belt grinder with dust extraction – the integrated dust extraction system provides a clean and safe working environment. Mobility and compact design – ideal for workshop and assembly applications. Robust construction – the rigid frame ensures high machining accuracy even under intensive use. High grinding efficiency – optimized for grinding surfaces and weld seams. Adjustable depth stop – enables precise control of the material removal depth. Easy and quick operation – ergonomic design and a simple control system. Construction and Technology The CORMAK PSM200 is based on a robust construction designed to ensure stability and vibration damping, significantly improving operating comfort and precision. The 2.8 kW motor, powered by a single-phase 230 V supply, provides sufficient power reserve for continuous operation. Iedpfxezynnys Afuobc The machine is equipped with a Ø200 × 300 mm flap wheel, ideal for smoothing edges, flat surfaces, and irregular metal surfaces. The integrated dust extraction system improves operator safety by reducing exposure to grinding dust. Precision and Performance The CORMAK PSM200 grinder has been designed for demanding industrial applications. The large working tool diameter and precise control of the machining depth enable consistent results, even when processing large workpieces. The adjustable grinding depth allows the operator to adapt the machine to the specific task, minimizing setup and changeover time. Applications The machine is designed for: welding and metalworking workshops, manufacturers of steel structures, railings, and tanks, industrial plants processing components that are difficult to clamp, service and maintenance teams, work carried out directly at assembly sites or in serial production. Standard Equipment Ø200 × 300 mm flap wheel Dust extraction system with filter Robust construction with adjustable depth stop Power cable with 230 V plug Protective housing for working components Technical Data Parameter Specification Power supply 230 V Motor power 2.8 kW Flap wheel size Ø200 × 300 mm Packaging dimensions 700 × 1000 × 600 mm