Used Belt Sanding Machine for sale (69,207)

Condition: not inspected (used), Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Hfodst Tqy Ejpfx Ab Sen Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: new, functionality: fully functional, color: other, Year of construction: 2026, Vertical Shaft Impact Crushers (VSI) stand out among rock crushing machines due to their high crushing efficiency and excellent particle shape production. Developed by CONSTMACH, these sand-making machines are used in the tertiary crushing stage to give cubic form to materials obtained from secondary crushers and to produce a high proportion of fine material. The system offers superior performance in processing all types of minerals and ores, as well as hard rocks such as basalt and granite. High-quality sand is produced from materials with a maximum feed size of 45 mm. Vertical shaft impact crushers allow you to easily obtain the desired product size for different material types thanks to their variable speed rotor system. It offers production capacity flexibility with a high reduction ratio, large feed hopper, and four different crushing chambers. In addition, high-chromium wheel shoes, anvils, and heavy-duty bearings ensure long life and low maintenance costs. The independent lubrication system and optional anvil replacement mechanism maximize uptime. Vertical Shaft Impact Crusher Technical Specifications Model: VSI-700-CR Maximum Feed Size: 35 mm Weight: 6,500 kg Motor Power: 110 kW Rotor Diameter: Ø700 mm Rotor Speed: 60–70 m/s Production Capacity: 60–100 t/h Model: VSI-800-CR Maximum Feed Size: 40 mm Weight: 12,000 kg Motor Power: 2 x 160 kW Rotor Diameter: Ø800 mm Rotor Speed: 45–60 m/s Production Capacity: 150–200 t/h Model: VSI-900-CR Maximum Feed Size: 45 mm Weight: 14,500 kg Motor Power: 2 x 185 kW Rotor Diameter: Ø900 mm Rotor Speed: 50–60 m/s Production Capacity: 200–250 t/h Model: VSI-1000-OR Maximum Feed Size: 90 mm Weight: 15,000 kg Motor Power: 2 x 200 kW Rotor Diameter: Ø975 mm Rotor Speed: 50–60 m/s Production Capacity: 250–300 t/h Why Choose CONSTMACH Vertical Shaft Impact Crushers? CONSTMACH is a globally preferred brand in the production of stone crushing machines and sand making machines with its engineering quality. Our vertical shaft impact crushers offer high performance, low operating costs, and long-lasting use. Our models, which can be customized to the production needs of each facility, provide the advantages of easy maintenance and high efficiency. CONSTMACH is always the right choice for businesses seeking quality, reliability, and sustainable production. What Do We Do at Constmach? Hodpfx Ajxqf Urjb Sjfn Constmach is a leading machine manufacturer serving the construction and mining industries with a wide range of products. Our product portfolio includes concrete block making machines, stationary and mobile concrete plants, stone crushing machines, stone crushing and screening plants, sand washing machines, sand making machines, asphalt plants, conveyor belt systems, jaw crushers, and mobile crushing plants. With its high quality standards, innovative production approach, and customer-focused solutions, Constmach stands out as a reliable brand in both national and international markets. Our products continue to be the preferred choice of industry professionals due to their durability, efficiency, and long-lasting performance.

Condition: used, Year of construction: 2001, This machine is fitted with a new Siemens PLC and touch panel. Technical specifications: - Manufacturer: Unisanding - Model: 2.2.0. 0-30 - Working width: 1300 mm - Year of manufacture: 2001, retrofitted in 2025 - 2 rollers, flexibly adjustable from 0–30°, operating from above - Flex-Trim special brushes - Vacuum belt with vacuum motor Hfodpsxtakmsfx Ab Sjn - With glass panel on the operator side - Sanding motors: 2 × 2.2 kW with thermal cut-out - Feed motor: 1 × 1.5 kW with thermal cut-out - Vacuum motor: 1 × 5.5 kW - Roller height adjustment axis: 1 × 0.18 kW - Feed speed: 2–10 m/min, frequency-controlled - Brush speed: 50–350 rpm, frequency-controlled - Voltage: 3 x 400 V, 50 Hz - Electrical power rating: 15 kW - Fuse: 63 A - Exhaust air volume (vacuum): 3,000 m³/h - Dust extraction volume: 5,000 m³/h (to be provided by the customer) - Length: 2,170 mm - Width: 2,040 mm - Height: 2,030 mm - Weight including control cabinet: 2,220 kg - Colour: RAL 7035 light grey/black - Operating side: left/right - Brush replacement side: right - Explosion-proof version: No - Location: at the Blomberg warehouse

Condition: used, Year of construction: 2015, machine/vehicle number: MB536013A, functionality: fully functional, power: 28 kW (38.07 HP), input voltage: 400 V, input current: 54 A, input frequency: 50 Hz, overall weight: 2,800 kg, We are offering this used COSTA MD5CC 1350 belt grinding machine, manufactured in 2015. Model: MD5CC 1350 Serial number: MB536013A Voltage: 400 V Hfjdszlcipepfx Ab Ssn Frequency: 50 Hz Power: 28 kW Current: 54 A Year of manufacture: 2015 Total weight: 2800 kg If you have any questions or require further information, please do not hesitate to contact us.

Condition: used, Year of construction: 2021, functionality: fully functional, Felder/Hammer edge sanding machine HS 950 for edge, surface, and contour sanding in woodworking shops. Suitable for finishing workpiece edges, moldings, frames, and wood components. Key technical data - Machine type: Edge sanding machine / oscillating belt sander - Model: Hammer HS 950 / Felder HS 950; according to the inventory note, the model is not clearly identifiable. - Sanding belt dimensions: approx. 2515 x 150 mm - Sanding table length: approx. 950 mm - Sanding belt speed: approx. 17 m/s - Motor power: approx. 2.2 kW Hfodoztxqfjpfx Ab Ssn - Table height adjustment: approx. 0–150 mm - Sanding unit tilt: approx. 45°–90° or continuously adjustable up to 90° - Dust extraction port: approx. 120 mm - Dimensions: approx. 1540 x 530 x 1235 mm - Weight: approx. 165 kg Features - Switchable oscillation for a uniform sanding pattern and longer sanding belt life - A useful addition for clean edge processing and finishing work - Of interest for carpentry shops, training workshops, and woodworking shops No guarantee.

Condition: used, Year of construction: 2006, incl. 2nd sanding padused, top equipmentmake SCM Samcotype EG 2500year of manufacture 2006machine . AM/28506motor 3.0 / 2.2 kWsanding length approx. 2500 mmsanding width approx. 1000 mmbelt length approx. 6800 mmtable size approx. 2500 mm x 1000 mmcranking right approx. 700 mmcranking left approx. 700 mmelectric adjustmentupper belt coverupper sanding supportbelt speeds 1400 /2800 rpm = 23 m/sec /46 m/secright-left runsuction connection D 160 mmspace requirement approx. 3900 mm x 1700 mm x 1500 mmtotal connected load approx. 4.55 kWstorage location 97447 Gerolzhofen, free loaded, unpackedhandover in as-is condition as inspected,without guarantee and warranty Hsdpfxovwffbj Ab Sjfn

Condition: new, Year of construction: 2022, I sell the new widebelt sanding machine Casadei Libra 45 RCT 110 Year 2022. Configuration: Steel moulding cylinder with spiral knives Combi unit hard rubber cylinder + segmented pneumatic jumping pad. Hfsdpfx Aberddh Is Sen Working width 1100mm Elektronic working height adjustment with digital readout 3-160mm 1 Motor 2 Feeding speeds. Programming of in/out jump of the pad. Sensitive adjustment of pad position. Sensitive adjustment of cylinders position. Pneumatic adjustment of pad and cylinders pressure position. Pressure rollers for short elements. Air-blow for cleaning the sanding band. Condition NEW ! The machine was not working before. Available immediately. Including full documentation and CE.

Condition: new, width of the strips 75.0 mm band length 2000 mm band speed 34.0 m/s total power requirement 3.0 kW weight of the machine ca. 75.0 kg dimensions of the machine ca. 570 x 570 x 1150 mm Description: - Excellent grinding performance thanks to high belt speed - Quick adjustment for horizontal and inclined positions - Continuous surface grinding area for optimal grinding of long workpieces - Versatile for grinding edges, surfaces, and for cylindrical grinding - Includes a quick-clamping system for fast belt changes - Easy adjustment of parallel belt alignment using an adjustment screw - Graphite coating on the flat grinding surface improves the sliding properties of the abrasive belt Hodpjz Auicofx Ab Ssfn Scope of delivery: - Sanding belt - Hinged protective shield - Sanding and support table - Workpiece stop - Emergency stop button - Machine base - Operatorâ??s manual (ENG)

Condition: new, width of the strips 150 mm band length 2000 mm band speed 34.0 m/s total power requirement 3.0 kW weight of the machine ca. 95.0 kg dimensions of the machine ca. 650 x 650 x 1150 mm Description: - Excellent grinding performance thanks to high belt speed - Quick adjustment for horizontal and inclined positions - Continuous flat grinding surface for optimal grinding of long workpieces - Versatile for grinding edges, surfaces, and for cylindrical grinding - Includes a quick-clamping system for fast belt changes - Easy adjustment of parallel belt alignment using an adjustment screw Hfodjz Auiispfx Ab Sen - Graphite coating on the flat grinding surface improves the sliding properties of the grinding belt Scope of delivery: - Sanding belt - Hinged protective shield - Sanding and support table - Workpiece stop - Emergency stop button - Machine base - Operatorâ??s manual (ENG)

Condition: new, Year of construction: 2024, Holzkraft Edge Sander Type: KSO 200 F with Veneer Sanding Attachment Sanding unit can be swiveled up to 45° via a lever The machine stand made of welded steel guarantees high torsional rigidity and vibration-free operation. Oscillating sanding belt with separate geared motor for better sanding results Oscillation can be switched on/off as required Sanding pad with graphite coating for a longer service life of the sanding belt Height-adjustable sanding table to utilize the entire width of the sanding belt Height-adjustable auxiliary table with dust extraction for sanding radii The spring-loaded belt tension automatically compensates for belt length differences. With double dust extraction Extendable roller table extension With rubber-coated sanding roller Veneer edge sanding attachment with contact shoe with fine adjustment, relief rollers and guide rails With grooved infeed guide for veneer overhangs Quick changeover from veneer edge sanding to solid wood sanding is possible Hfodpfx Abolht H Ne Sen Dimensions and Weights Length approx. 1900 mm Width/Depth approx. 900 mm Height approx. 1350 mm Weight approx. 290 kg Connection for dust extraction Dust extraction nozzle diameter 140 / 100 mm Drive power Oscillation motor 0.25 kW Work table(s) Work table length 960 mm Work table width 350 mm Work table height adjustment 230 mm Height min. 735 mm Height max. 965 mm Longitudinal table height adjustment 230 mm Cross table length 330 mm Cross table width 330 mm Cross table height min. 720 mm Cross table height max. 900 mm Cross table height adjustment 180 mm Electrical Data Power of drive motor 3.0 kW Connection voltage 400 V Sanding unit Sanding belt length 3000 mm Sanding belt width 200 mm Belt running speed(s) 20 m/s Sanding area length 1050 mm Sanding area width 200 mm Oscillation stroke 20 mm Location: In stock at 54634 Bitburg - available immediately -

Condition: new, Year of construction: 2024, Working width: 950 mm Workpiece height min: 4 mm Workpiece height max: 170 mm Hfjdpfx Abeknyhls Sen Height adjustment: electronic Workpiece thickness display: digital Control unit: Fox 500 KTR Units: 1 1st unit: Combination unit for calibrating and sanding / Bevel-grooved steel roller, Ø 120 mm, with fine height adjustment / Hard sanding shoe with graphite support Dust removal brush: no Motor power: 7.5 kW Dust extraction connection: 140 mm Machine length: 1388 mm Machine width: 1545 mm Machine height: 1668 mm Weight: 660 kg

Condition: new, Hoku KS 150 edge sander manufactured by Rehnen. The upper section is made of heavy-duty cast iron with a built-in three-phase motor 380 V, 2.2 kW, 2850 rpm; the machine is equipped with a built-in switch-plug combination; Motor protection switch and main switch in accordance with VDE regulations; Sanding belt back panel dimensions: 850 x 150 mm; steel table height adjustable by spring pressure; belt dimensions: 150 x 2280 mm; The sanding belt back panel is covered with a graphite sliding coating; The machine is supplied with an assortment of sanding belts; A square and miter gauge is also included. The machine is dust-tested (GS) by Holz-BG-Stuttgart when connected to a central extraction system with an air speed of at least 20 m/s. - Swivels 90-180° - Motorized belt oscillation - Small support table on the idler pulley - Pneumatic belt tensioning Technical specifications: Motor power: 2.2 kW Hsdpfowgc D Sjx Ab Sjfn Sanding belt dimensions: 150 x 2280 mm Sanding belt speed: 22 m/s Table size: 750 x 350 mm Space required: 1000 x 800 mm Weight: from 180 kg Extraction diameter: 100 mm

Condition: used, Year of construction: 1997, functionality: fully functional, machine/vehicle number: 02/96088A, total length: 7,500 mm, total width: 2,000 mm, total height: 2,000 mm, overall weight: 7,500 kg, Edge grinding machine with 10 programmable profiles, including rounded edges Pre-milling cutter 10 face milling operations 4 chamfering operations Hsdpfxjzpy Drj Ab Sjfn 2 water break grooves Calibration support Belt feed direction from left to right Deburring cutter Unit for water break grooves from above and below Can grind 9 profiles – e.g., bullnose, full round, half round, small rounding on the top and bottom, chamfered, quarter round.

Condition: used, Year of construction: 2010, - Perfect for surface finishing - Constant working height - Q/L/Q Fine/cross-sanding machine Hfsdpfszuzctox Ab Sjn Manufacturer: Weber Type: KSF-3-1350 Year of manufacture: 2010 Technical data - Equipped with 3 sanding belts for high-quality fine, veneer, and high-gloss sanding. - With a constant working height Machine frame - Heavy-duty steel welded construction for mounting 3 sanding units - Constant inlet height of 900 mm - Control and sanding belt change side on the inlet side, on the left - Stepless feed speed of 3-18 m/min, frequency-controlled. - Vacuum version of the conveyor belt / with 1 vacuum blower 5.5 kW, and a vacuum channel up to the upper edge of the machine Unit 1: Cross-belt unit - Pressure pad belt with felt and graphite for long service life - ISD segmented pressure bar system with 11 mm workpiece detection and 44 mm pressure pad width - Workpiece-controlled sanding belt blowing device Unit 2: CBF combination unit - One grooved rubber contact roller 0 130 mm, rubber hardness 60 Shore - One cross-running flap band with separate drive 4.0 kw - ISA segmented pressure bar system with 11 mm workpiece detection and 22 mm pressure pad width (counter-rotating) - Workpiece-controlled oscillating sanding belt blowing device Unit 3: Cross-belt unit - ISD segmented pressure bar system with 11 mm workpiece detection and 44 mm pressure pad width - Workpiece-controlled sanding belt blowing device Operator terminal SIEMENS" MP 377 12" Multi-Panel - Graphical user guidance via 12" color display - Program memory with 300 programs - Setting of all parameters via program WEBER i-Touch control - One rotary knob for navigating through the most important functions WEBER AWDM - Automatic thickness adjustment at the machine inlet with start switch Overthickness - Selector switch at the machine inlet with the following functions: - Automatic lifting of the contact roller and the segmented pressure bars - Feed stop ISA/ISD control - High-resolution workpiece detection in a 22 mm grid - Free loading of complex part shapes - Multiple loading with a small lateral distance - Sanding intensity individually adjustable at all edges - Sanding pressure adjustable via program ISA segmented pressure bar system (Unit 2) - Pressure pad movable in the longitudinal and transverse direction ISD segmented pressure bar system (Unit 1+3) As ISA, but additionally with - Separate adjustable pressure for the edge area (higher or lower) - Optionally only on the outer edge or outer and inner edges - Longitudinal and transverse edges or only longitudinal edges can be adjusted Workpiece blowing device - with WEBER ES system - Energy-saving, workpiece-controlled workpiece cleaning with single slider control WANDRES-Micro-Cleaning (single brush version) - Power sword brush with integrated micro-humidification of the linear brush (for optimal paint dust removal) Technical data - Working width: 1350 mm - Drive Unit 1 (frequency-controlled-Eco-Drive): 15.0 kW - Drive Unit 2 (frequency-controlled-Eco-Drive): 20.0 kW - Drive Unit 3 (frequency-controlled-Eco-Drive): 15.0 kW - Drive CBF: 3.0 kW - Drive vacuum blower: 5.5 kW - Drive feed (frequency-controlled): 3.0 kW - Drive height adjustment (frequency-controlled): 0.75 kW - Sanding belt speed (frequency-controlled): approx. 3-20 m/s - Sanding belt dimensions cross belts (W x L): 2x150x5100 mm - Sanding belt dimensions wide belt (W x L): 1370x2620 mm - Workpiece thickness (min./max.): 4-140 mm - Working height (constant): 900 mm - S

Condition: used, total length: 1,700 mm, total width: 1,200 mm, total height: 1,700 mm, overall weight: 600 kg, grinding belt length: 3,000 mm, grinding belt width: 200 mm, power: 4 kW (5.44 HP), No. 04535 Two-sided edge sanding machine HÖFER BSM V pn / BSM 5 pn Used Double-sided edge sanding machine Drive motor 4 kW Oscillation motor 0.75 kW Belt speed 22 m/s Pneumatic belt tensioning Pneumatic height adjustment Belt dimensions 3000 x 200 mm Front sanding table 900 x 400 mm, pneumatically tiltable up to 45° Rear sanding table 900 x 400 mm, with veneer edge sanding device Transport dimensions approx. 1700 x 1200 x 1700 mm LWH Weight approx. 600 kg To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical specifications, condition description, year of construction and scope of delivery according to manufacturer’s brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Hedpfozg Itvox Ab Sefn Payment terms: Prices plus VAT, payment before collection or shipment Delivery terms: ex warehouse

Condition: used, Year of construction: 2022, Belt width: 150 mm Belt length: 3000 mm Table size: 960 mm x 350 mm Auxiliary table: 330 mm x 330 mm Veneer sanding device: yes Oscillation: yes Tilting sanding unit: yes Extraction port: 120 mm Motor power: 3 kW Machine length: 1910 mm Hedpozq Dczjfx Ab Ssfn Machine width: 840 mm Weight: 330 kg

Year of construction: 2010, operating hours: 7,546 h, condition: good (used), functionality: fully functional, machine/vehicle number: 04810, We are offering this well-maintained COMANDULLI OMEGA 100 edge grinding machine for round edges, manufactured in 2010. Manufacturer: COMANDULLI Model: OMEGA 100 Year of manufacture: 2010 Condition: good Category ID: 430 Machine type: Edge grinding machine for round edges Configuration: Belt running direction: left to right Pre-grinding support for end faces Thickness gauge 1+1 automatic pre-grinding supports 45° 8 end face grinding supports for straight and round edges 2 upper and 2 lower chamfering supports Swiveling device for chamfering supports for easy processing of pencil edges Hedpfx Aezyuckob Sefn Finishing grinding support 2 roller tables, each 2m long The machine is currently in operation in Australia; the price includes transportation CIF to a European port of your choice. If you have any questions or require further information, please feel free to send us a message or call us.

Condition: used, Year of construction: 2002, Used machine Year of manufacture 2002 Edge sander with electromechanical oscillation with a 15 mm pendulum stroke of the motorized disc Swivel of the sanding unit by 90° using a hand crank (continuous angle adjustment; read off the scale) Hfjdpow I U Ahefx Ab Sen Additional table with extraction system for using sanding rolls Height-adjustable table for utilizing the sanding belt Motor 2.2 kW Oscillation motor 0.11 kW Table size 880 x 370 mm Belt dimensions 150 x 2580 mm Dimensions 1700 x 1000 x 1150 mm Weight 250 kg Availability: Short-term Storage location: Flörsheim

Condition: refurbished (used), Year of construction: 2026, Dear customers, we are currently offering a fully refurbished vertical belt sanding machine for model and mold making by F. Zimmermann. Here are the machine’s technical specifications: Sanding belt width: 250 mm Sanding height: 400 mm Belt length: 2,400 mm Sanding speed: 18 m/s Worktable: 750 x 350 mm Swivel range: 30/45° Power: 4.0 kW Speed: 1,400 rpm Extraction port diameter: 120 mm Including angle stop Including sanding belts Foot emergency stop Dimensions: 990 x 850 x 1,740 mm Weight: 470 kg The machine has been painted in RAL 7035 light grey, the sanding plate is completely new, the roller bearings have been replaced, and various other small parts have been exchanged. We have also installed a motor brake and several additional electrical components for enhanced machine safety. The machine comes with a 6-month warranty. Price plus VAT, which will be separately itemized on the invoice. If you have any questions, please feel free to contact us. Hfodpfx Abozlh Ude Sen

Year of construction: 2013, condition: used, Number of sanding units 4 st. sanding width max. 200 mm Sanding height max. 7-150 mm Working speed 8-16 m/min Band Speed 18-30 m/sec Stähle-Hess Sanding Machine Saturn-Duo ----- Manufacturer's Technical Description: Stähle-Hess Finish Sanding Machine, Model Saturn Duo Featuring 2 sanding units, plus additional upper and lower Roto-Finish sanding units. 1 Upper sanding belt 1 Lower sanding belt 2 Upper Roto-Finish sanding units Hfjdpfxoy Spvle Ab Sjn 2 Lower Roto-Finish sanding units Workpiece Dimensions Height: 7–150 mm Width: max. 200 mm Minimum length: 300 mm Belt speed: 18–30 m/s (variable) Feed rate: 8–16 m/min (variable) ----- Price for the above-mentioned machine available upon request! ----- Note: This machine was previously used in conjunction with a Weinig Variomat four-sided planer/moulder (see Stock No. #7007). (Technical specifications provided by the manufacturer – subject to verification!) All listed prices are net, plus applicable statutory VAT.

Year of construction: 1991, condition: used, Used machine Year of manufacture: 1991 With 4 sanding units Workpiece dimensions: Thickness min. 10 mm max. 150 mm Width min. 10 mm max. 180 mm Length min. 190 mm, max. unlimited Abrasive belt dimensions: 200 x 1800 mm Extraction ports 2 extraction ports 80 mm 4 extraction ports 120 mm Required air velocity: 30 m/sec L x W x H: 3400 x 1150 x 1805 mm Hfjdpfx Asw Tfxdsb Ssn Weight: 2400 kg Availability: short term Location: Odenwald

Condition: excellent (used), Heavy-duty double-sided edge sanding machine, oscillating Motor power approx. 3.0 kW Oscillation with own motor approx. 0.2 kW Sanding belt dimensions 3000 mm x 200 mm Front sanding table 980 x 340 mm rear sanding table 750 x 300 Space requirement L x W x H approx. = 1800 x 1500 x 1000 mm Weight approx. 600 kg Front sanding table with veneer edge sanding device Rear sanding table with infinitely variable angle adjustment Angle stop on rear work table Oscillation by means of gear motor Pneumatically height-adjustable sanding beam Interchangeable radius sanding discs Pneumatic belt tension, adjustable Extraction with blower Attachment option for feed unit 2 lateral support tables for radius sanding Note on used machines: Hedpfxeuxqzuj Ab Ssfn - Subject to errors in technical specifications and prior sale. - Prices quoted are ex location - free loading! - The machines have been cleaned and functionally tested. - All machines are purchased as seen without any warranty. The buyer is free to inspect the machines on site. - Special agreements are only possible in written form. (Inquiries will only be answered with your address and telephone number).

Condition: used, Technical data: Hodpfx Aozryw Rjb Ssfn - Conveyor belt width: 150 mm - Motor: 3 kW - Weight: 490 kg

Condition: used, Year of construction: 1995, Constant machine - combination station, dust brush - thickness measuring device - electronic segmented sanding pad MCS System Weber 32 mm - grooved steel calibrating roller - belt blow-off - vacuum conveyor belt. Sanding width: 1100 mm Drive: 15 kW Feed approx. 1.1 kW Height adjustment 0.25 kW Sanding belt dimensions: 1150 x 2500 mm Max. workpiece thickness: 150 mm Machine width: 1700 mm Machine length: 2000 mm Machine height: 2160 + 150 mm Machine weight: 1900 kg Constant working height: 850 mm Extraction connector: belt 180 mm / brush 120 mm Suction air volume: 0.74 m³/s Connected load: 23 kW Compressed air supply: 7 bar Feed speed: 3-15 m/min. Operating hours: 7000 h Location: Nattheim Hodpfxex Twcpe Ab Sofn

Condition: new, Edge sanding machine KSO 1505 Holzkraft -Exhibition machine- - Dust extraction port diameter: 100 mm - Work table length: 900 mm - Work table width: 305 mm - Work table height adjustment: 120 mm - Connection voltage: 400 V - Mains frequency: 50 Hz - Sanding belt length: 2750 mm - Sanding belt width: 150 mm - Belt speed(s): 16 m/s - Oscillation stroke: 15 mm - Sanding area length: 1010 mm - Sanding area width: 190 mm - Maximum sanding height: 170 mm - Swivel angle of sanding unit: 0 – 90 ° - Maximum workpiece width: 1010 mm Hfjdpfjvxkv Ujx Ab Sjn - Maximum workpiece height: 150 mm Dimensions and weights: - Length (product) approx.: 1515 mm - Width/depth (product) approx.: 550 mm - Height (product) approx.: 1150 mm - Weight (net) approx.: 207 kg -1x sanding belt 2750x150mm, grit 80 -1x sanding sleeve Ø38mm, grit 80 -1x sanding sleeve Ø50mm, grit 80 -1x sanding sleeve Ø75mm, grit 80 - New exhibition machine -