Used Schaal Automatic Punching Press for sale (32,873)

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding. Isdpozuzw Djfx Aatjif

Condition: ready for operation (used), Year of construction: 1995, operating hours: 41,000 h, functionality: fully functional, FOR SALE: BRUDERER BSTA 50USL High-Speed Stamping Press With Automatic Strip Feeder BBV 190 500 kN | 100–1120 spm | Fully automatic | Top-tier Swiss quality Technical Highlights: Nominal force: 500 kN Stroke rate: 100–1120 strokes per minute Working hours: 41000 h Main motor: 22 kW Control voltage: 24V DC Power connection: 400V / 50Hz / 62 kVA Adjustable stroke: 16 / 19 / 25 / 32 / 38 /44 / 51  mm Shut height adjustment: 64 mm Working Dimensions: Max tool installation width: 1100 mm Strip pass width: up to 256 mm Ram area: 980 × 420 mm Table area: 1080 × 650 mm Strip entry height adjustable: 60–140 mm Max strip width: 120 mm Max feeding pitch: 85 mm Max material thickness: 4 mm Feeding angle: 180 Deg Machine Dimensions (with BBV 190): Machine footprint (L × W × H): 2407 × 1278 × 3150 mm Iijdswpg Rbopfx Aatef Weight (approx.): 8,000 kg Equipment Includes: Feeder BBV 190 – fully synchronized mechanical strip feeder system Integrated control cabinet Pneumatic clutch and brake Adjustable stroke and shut height Compressed air connection: 6–10 bar Oil cooling unit included Ready for integration with peripheral systems Condition & Delivery: Machine in excellent technical and visual condition Fully serviced and tested Immediate availability from Europe Worldwide shipping & installation support available Contact us today for pricing and further technical details. Let us help you upgrade your production line with Swiss precision engineering.

Condition: good (used), functionality: fully functional, Peddinghaus profile and punching machine with automatic stop Very well maintained Punching force 45 t Iiedpfxsyg D Nno Aatef Incl. various punching dies

Condition: good (used), Year of construction: 1998, Neat used punching machine from Euromac Type CX 1000 30 Capacity 30 ton Unloading 1000mm Iiodpfx Aajzulx Ejtsf Overwrap up to 10000mm Including drawer cabinet with lots of tooling and multitool

Condition: reconditioned (used), functionality: fully functional, ram adjustment: 40 mm, installation height: 2,500 mm, pressing force: 30 t, stroke length: 40 mm, High Speed Automatic Punching Press. Machine with CE certificate and EUR1 certificate of European origin. Equipped with twin synchronized double rolls feeds for strips widths from 5 mm – 150 mm. PLC touch screen logical interface control. Numerically controlled stamping process (NC). With stroke and speed counter, programmable length, auto stop. Three working modes: Manual, One stroke and Automatic. Pneumatic clutch and brake. Operator’s instruction manual in English. Stroke power: 300 [KN] (30 [tons]). Iijdpfx Asvkfmrsatsf Adjustable stroke: 8-40 [mm]. Table: 540 x 300 [mm]. Adjustable speed 100 – 600 strokes per minute up to 10 in one second. Maximum strip thickness 2.5 [mm]. Central lubrication. Power consumption 5.5 [kW] Technical Air 5-10 [bar]. Warranty: 1 year. Two feeders are used when you need to stamp very thin, soft strip or very heavy strip, to secure precise feeding. All specifications non-binding , subject to change without notice.

Condition: used, Year of construction: 1992, functionality: unexamined, Technical Specifications Iiodpfoyktftsx Aatof Make and model: Bruderer BSTA 25 EL Nominal capacity: 250 kN, 25 tons Year of manufacture: 1992 Year of control upgrade: 2020 Max. number of strokes: 100/1425 Adjustable stroke: 13, 16, 19, 25, 32, 38 mm Table dimensions: 640 x 530 mm Passage between the supports: Longitudinal 640 mm; Lateral 220 mm. Fitted with roll feeder BBV 190/85 on right hand side. Max width of strip: 160 mm Feed length: variable up to 85 mm max Optional: Sound insulating cabin Oil pump. Heat exchange oil cooler. Front and rear safety guards. Fitted on 4 spring feet. Slide/Ram adjustment: 51 mm Documentation included. Press weight cca. 5000 kg.

Condition: refurbished (used), Year of construction: 2006, functionality: fully functional, Refurbished BRUDERER Stamping Press BSTA250-75B incl. new PCS-100 Press Control Technical Specifications Isdpfxjyb Etqj Aatjif Pressing force: 250 kN Tool area (L-R x F-B): 750 x 530 mm Adjustable stroke lengths: 13, 16, 19, 25, 32, 38, 44, 47 mm Speeds: 13 mm stroke: 1,500 spm 16 mm stroke: 1,350 spm 19 mm stroke: 1,240 spm 25 mm stroke: 1,075 spm 32 mm stroke: 950 spm 38 mm stroke: 810 spm 44 mm stroke: 700 spm 47 mm stroke: 650 spm Power supply: 76 kVA Servo motor rating: 47 kW Shut height: 175.5 - 239 mm (stroke-dependent) Slide adjustment: 51 mm Strip feed width: 210 mm Strip feed height: 50 – 120 mm Additional Information · Completely refurbished eccentric high-speed press · Highly dynamic, adjustable stroke design · Equipped with modern, high-performance modular PCS-100 press control · Energy-efficient drive technology for reduced CO₂ emissions · Industry 4.0 ready via OPC-UA interface · Integrated tool monitoring · Integrated servo feed system

Condition: used, Year of construction: 2006, Stamping Press Manufacturer: Schuler Pressen GmbH & Co. KG, Göppingen, Germany Type: SAL 250-1.9 Mark II Serial number: A/260156 (Machine No. 2006-260156) Year of manufacture: 2006 Press force: 2,500 kN (250 tons) Stroke rate: 80–400 strokes/min Drive power: 51 kW at 2,000 rpm Ram stroke: 30 mm Ram adjustment: 100 mm Iedpfx Aajzil S Istjif Ram lift: 75 mm Installation height (table plate to ram, ram stroke bottom, ram adjustment top): 550 mm Table dimensions: 1,950 x 1,060 mm (as per drawing) Ram face: 1,950 x 800 mm (as per drawing) Compressed air: 5.5 bar Total weight (excl. feed): 48,000 kg Control system: SYS PACO 8000 Sound-insulating enclosure (orange) Strip Feed Unit Manufacturer: Kohler Maschinenbau GmbH, Friesenheim, Germany Type: KRS 18.260/19-2000.2H-BF1 Serial number: 40 871 Year of manufacture: 2006 Connected load: 15.5 kW Supply voltage: 400 V, 50 Hz Decoiler Manufacturer: Kohler Maschinenbau GmbH, Friesenheim, Germany Model: 18 260-1000.2 Serial number: 40 466 Year of manufacture: 1984 Connected load: 8 kW Supply voltage: 380 V, 50 Hz

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, pressing force: 48 t, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 450 kg, Equipment: documentation/manual, HSM VK 4812 P Year of production: 2017 Fully automatic baler. The device has service and maintenance work by an authorized HSM service with a branch in Germany. Press after significant service work - details after direct contact. The baler comes complete with a ramp for ejection of finished bales and stands for binding wires. Pressing force: 480 kN Drive power: 18 kW Voltage / frequency: 400 V / 50 Hz Capacity at 50 kg/m³: 10.2 t/h Bale width x height x length: 1100 x 750 x 600 - 1200 mm Total length x width x height: 6661 x 3994 x 2583 Machine weight: 10.2 t Compressed material: foil, mixed paper, cardboard, die-cutter waste Bale tying: 4-fold with wire We also have other presses in stock. Transport costs depend on weight, volume and, above all, distance, the following information is important for inquiries: Delivery address (postal code and city name), but further details require telephone contact, so please inquire about transport costs and other delivery methods to contact us contact us by phone. Our contact details can be found in the seller's legal information. Iijdpfx Aezff Smoatef We sell and export worldwide, and thanks to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-Community invoices - without VAT. opening hours Mon-Fri: 8:00-16:00 Sat: closed

Condition: used, functionality: fully functional, Year of construction: 1989, machine/vehicle number: 4867, Pressta Eisele Stamping Machine HE 40 S Iedpfx Aajy Tizkjtoif Price: 2,000 Euros

Condition: excellent (used), Complete production line for sale for manufacturing round metal rainwater drainage systems. Production starts from a sheet metal coil, then forms, stamps, and packages the products. All machines are in very good condition. The equipment is fully assembled and intended for mass production of: - Gutters - Gutter ends - Connectors - Corners Iiodoy I Tq Sjpfx Aatef - Brackets - Downpipe outlets - Elbows - Downpipes - Branch connectors (Tees) - Packaging If you are interested in the offered equipment, have any questions, or would like to receive more detailed information, please do not hesitate to contact us. We will gladly provide the full equipment list, technical specifications, additional photos, or arrange an inspection of the production line. All equipment is connected and can be inspected in operation to see the full production process.

Condition: used, Eccentric stamping press HAULICK + ROOS, Type RVD 125 Double-column eccentric press Machine No. 212560, Year of manufacture 1981 Pressing force 125 tons Table size 880 x 800 mm Table opening 470 x 140 mm Column distance 900 mm Column distance, side 415 mm Iiodpfx Aohlnzkjatof Ram stroke 45 mm Ram adjustment range 0-80 mm Installed height as shown in the picture 340 mm Stroke rate 50 to 300 strokes/min Motor power, main drive 22 kW Power connection 380 volts, 50 Hz - Double connecting rod drive with 4-bearing eccentric shaft for off-center ram pressure load - Adjacent electrical cabinet - NC roller feed EBU, width 250 mm, year of manufacture 2003 - Adjacent control panel for the roller feed - Strip feed direction from left to right Space requirement (press) L x W x H 3000 x 2000 x 3020 mm Transport height 2950 mm Weight of the press approx. 11 tons

Year of construction: 2001, condition: ready for operation (used), functionality: fully functional, punching force: 1,000 t, operating speed: 93 mm/s, stroke length: 55 mm, table length: 1,100 mm, table width: 800 mm, machine/vehicle number: 100597, TECHNICAL DETAILS Press force: 10,000 kN Table surface (W x D): 1,100 x 800 mm Stroke range: 15 - 55 mm Clearance at max. stroke: 28 - 98 mm Puzzle thickness: up to 3 mm Format width (max.): 1,100 mm Punching speeds Upwards: 47.8 mm/s Downwards: 93.7 mm/s Punching: 0.28 mm/s Hydraulic unit Type: 250 Dimensions (L x W): 1,310 x 910 mm Oil capacity: 670 l Unit weight: 1,000 kg Oil weight: approx. 550 kg Weight with oil fill: approx. 1,550 kg Automatic punching table Type: 355 Table top size (W x D x thickness): 1,000 x 700 x 10 mm Iijdpsy Ampdefx Aatjf Hardness: 62 HRC Surface finish: 7 MACHINE DETAILS Electrics Operating voltage: 400 V Frequency: 50 Hz Rated machine current: 50 A Incoming line protection: 63 A Control voltage: 230/24 V Rated power: approx. 30 kW Protection class: IP 54 Power requirement: approx. 8 kW Pneumatics Operating pressure: 6 bar Dimensions & Weight Puzzle disassembler dimensions (L x W x H): 3,150 x 1,620 x 2,900 mm Working height: approx. 1,700 mm Total weight: 33,000 kg Weight of puzzle disassembler: approx. 1.8 t Noise level: < 70 dB(A)

Condition: used, Year of construction: 2025, total length: 1,450 mm, total width: 800 mm, total height: 2,200 mm, Colour: Blue Empty weight: 970 kg Price: On request Movable Press-Cylinder - Year: 2025 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes - Operating hours: 0 - Drive system: Conventional - Press model: Workshop press - Press configuration: Single-acting - Press force [ton]: 100 - Max. stroke [mm]: 380 - Table length [mm]: 1500 - Table width [mm]: 300 - Ram length [mm]: 100 Iiodpfjztxnksx Aatjf - Throat depth [mm]: 1100 - Height adjustment [mm]: 750 - Motor power: 3.0kW - Transport dimensions: 1450mm x 800mm x 2200mm (l x w x h) - Transport weight [kg]: 970kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 1977, Stamping Press Manufacturer: Bruderer AG, Arbon, Switzerland Type: BSTA 110 Serial number: 4343 Year of manufacture: 1977 Press force: 110 tonnes Stroke rate: 100–850 strokes/min Stroke (adjustable): 16, 19, 26, 35, 43, 51, 58, 64, 70, 75 mm Ram adjustment: 89 mm Max. tool installation width: 1,170 mm Max. strip feed width: 400 mm Iisdpfx Aaozil Suotof Strip feed height above clamping plate: 80–180 mm Bed opening: 1,120 x 400 mm Connected load: 50 kW Supply voltage: 3 x 380 V AC, 50 Hz Control voltage: 24 V AC Compressed air connection: R ½", 6–10 bar Machine dimensions (H x W x D): 3,930 x 3,320 x 2,250 mm Total weight incl. strip feed: approx. 24,600 kg Strip Feed Unit Manufacturer: Bruderer AG, Arbon, Switzerland Type: BBV 320/200 Max. feed: 200 mm Max. strokes/min: up to 1,000 (feed-dependent) Accessories Kohler unwinder Heспо straightener SYS PHS 5000 Sound-insulating enclosure (orange)

Condition: excellent (used), Here, we offer you a TOX full-punch riveting system. TOX full-punch riveting system, type TZ-VSN. The full-punch rivet first severs all joining partners and then punches the rivet button out of the joining point. With its innovative technology for full-punch rivets, TOX PRESSOTECHNIK, the specialist for sheet metal joining, expands its range of products and services with a forward-looking process. Full-punch riveting provides an additional mechanical sheet metal connection, which is of great importance for lightweight constructions and the joining of hybrid parts and assemblies. The rivet feeders, clamp and tool holders are also designed to be universal, so that full-punch rivets with diameters of 4.0 mm and lengths between 3.3 and 8.1 mm, as well as full-punch rivets with diameters of 5.0 mm and lengths between 3.9 and 9.0 mm, can be processed flexibly with both TOX hand clamps and TOX robot clamps. Iedszdtffjpfx Aatoif Type TZ-VSN Press force 55 kN Total stroke 140 mm Rivet type: diameter 5x4.6 Connection values Power: 3.4 kW Mains connection: 400/15/50-60 V/A/Hz Speed: 200 mm/s Mains type: 3P+N+PE Control voltage: 24 V DC Pre-fuse: 25 A Type: TZ-VSN Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data and information are subject to change!) We would be happy to answer any further questions you may have by telephone. Written orders can be placed by email or fax.

Condition: like new (used), UNDER CONSTRUCTION We are currently in the final stages of a complete overhaul of a fully automatic stationary press. This stationary press is including 2 containers 30m3 equipped with side door Build in: RV 2025 Overhaul work we have carried out: -new floor -new side panel -new guide blocks and guide plates - pressblock overhauled Ijdow Uc T Ujpfx Aateif -cylinders fitted with new sleeves -new fork pins -new return filter -new hydraulic hoses -oil renewed

Year of construction: 2025, condition: new, Hydraulic C-frame press (punch press) Iiodpfjwag Rijx Aatef Year of manufacture: 2025 Capacity: 100 tons at 230 bar Control / key switch: 1. Manual setup mode without light sensor 2. Automatic (at full speed) with light sensor Main cylinder: Ø 230 mm Auxiliary cylinders: 2 x Ø 50 x 30 mm Auxiliary guide: 2 x Ø 50 mm Motor: 11 kW – 15 hp Pump: 16 cc – 23 liters / ASC – Helical gear pump Speed: Forward 110 mm/sec – Return 200 mm/sec Pressure phase: 9 mm/sec Installation height: 500 mm Stroke length: 400 mm. Push plate: 750 x 600 mm. – with T-slots Table top: 750 x 600 mm. – with T-slots Table height: 850 mm. (Floor to table top edge) ----- Hydraulic accessories: Hydraulic control block & accessories: REXROTH Pressure adjustment via PLC. (20 – 100 tons) Speed adjustable via PLC. Air cooler Feed valve NG.63 Control accessories: Siemens S7-1200 Blsbjftg Sgsmmvyhwof Main control box Foldable control panel With side safety door (doors can be moved backwards) SICK 750 + 150 mm light sensors. Ruler for adjusting the stroke length 7" PLC screen – Siemens Movable two-hand control Alarm indicator for faults (light & sound) ----- • The press complies with the EN693 Machinery Directive • Hydraulic two-way valves • Dual-channel fused control system • Safety PLC – SICK • Operating instructions & parts list (German) • Warranty: 24 months ----- Oil capacity: 190 liters (Tank volume: 205 liters) Total weight: approx. 5,500 kg. Overall dimensions: 1300 x 2000 x 2750 mm. Delivery time: 2 - 3 weeks from stock. Paint finish: Light gray & dark gray The machine is available immediately in 2 - 3 weeks. Freight: approx. €2,000 from Konya to Germany

Year of construction: 2016, condition: ready for operation (used), Pressing force: 800kN, max. tool installation height: 380mm, max. upper tool weight: 300kg, stroke adjustment: 8mm-140mm, ram height adjustment: 100mm, stroke rate: 100/min, throat depth: 350mm, table dimensions X/Y: 850mm/670mm, ram area: 550mm/400mm. Machine dimensions X/Y/Z: approx. 2250mm/1550mm/2750mm, weight: approx. 9000kg. The machine was completely overhauled by the manufacturer in 2016 (retrofit). In 2024, the clutch, rotary union, press safety valve, and hydraulic oil cooler were replaced. In 2021, the drive motor and belt for the flywheel were converted to frequency-controlled speed. Documentation available. An on-site inspection is possible. Iijdpfx Ajxq Exwsatsf

Condition: good (used), functionality: fully functional, Weight: 3.5 tons Punching force: 1000 kN Reach: 760 mm Iiedpfxoztknpe Aatef Can punch, for example, a 40 mm hole in 22 mm steel Drive power: 8.5 kW Height (approx.): 2.15 m Width x Depth (approx.): 0.8 x 2 m Stroke release via foot switch.

Condition: used, Year of construction: 2003, Manufacturer: Haulick + Roos GmbH Type: RVD 3000-2500 Machine Type: High-performance stamping press Year of manufacture: 2003 Condition: used Rated pressing force: 3,000 kN Pressing force: 300 t Stroke frequency: 20–180 strokes/min Drive power: 80 kW Ram stroke: 20–160 mm Ram adjustment: 150 mm Tool installation height: max. 450 mm Maximum tool length: 2,500 mm Maximum tool width: 1,000 mm Table area: 2,450 × 1,000 mm Ram area: 2,500 × 950 mm Clamp plate opening: 2,250 × 350 mm Machine weight: approx. 46,000 kg Strip feed direction: right to left Power supply: 400 V Frequency: 50 Hz Maximum connected load: 80 kVA Maximum fuse rating: 250 A Draw cushion: not available Components of the system: Haulick + Roos high-performance stamping press RVD 3000-2500 DIMECO coil unwinder, type 23S1/D/VV Year of manufacture: 2003 Weight: 1,450 kg Maximum load capacity: 4,000 kg DIMECO roller feed, type 1681/17/BVV Year of manufacture: 2003 Weight: 540 kg ARKU straightening machine Technical data for roller feed: Strip width: 5–420 mm Strip thickness: 0.1–5 mm Maximum strip cross-section: 1,000 mm² Strip speed: up to 125 m/min Iisdpfxszrz Dxe Aatjf Feed length: 0.1–999.9 mm Feed accuracy: ±0.1 mm Roller diameter: 100 mm Strip height adjustment: 100 mm, manual mechanical Note: The ram guide should be replaced. The system is currently still in operation and functional. A quote from the manufacturer for complete disassembly and installation of new guides is available for approximately €200,000. We will gladly provide videos of the system in operation upon request.

Condition: used, Heavy-duty hydraulic hole-press, perforated panel press or gluing press for gluing or securing workpieces such as frames, panels, windows or doors. Technical data: - Cylinders: 6 - Hold-down units: 3 Iisdpfx Aajzryy Setof - Pressing area: 260 x 145 cm

Condition: used, Punching force: 200 kN Thread, for example a 13 mm hole in 12 mm steel Ijdpjrmudgefx Aateif Viewfinder via handwheel Assortment of tools is included in the price

Condition: ready for operation (used), Year of construction: 1995, pressure 35.0 t plate thickness max. 8.0 mm Iiedpfezf Nrkox Aatof throat 830 mm diameter of seal max. 105 mm table: 1500 x 1200 mm work height max. 920 mm die stroke ca. 90.0 mm strokes per minute ca. 200 Pressure power 220 bar oil volume 80.0 l total power requirement 4.0 kW weight of the machine ca. 3200 kg range L-W-H 1600 x 1800 x 1800 mm The IS 35 hydraulic punching machine has been specially optimized for processing sheet metal and extruded parts. It stands out for its flexibility and manufacturing precision. The machines in the IS series are equipped with 35 metric tons of punching force. Features: - Electro-hydraulic punch press with long reach - Robust C-frame construction * Solid cast or welded frame (C-shape) * Extremely high punching precision * Compact design = small footprint * Hydraulic overload protection - Separate control unit - Single and continuous stroke selectable - Infinitely adjustable controller for: * â??top dead centerâ? - Continuously adjustable control for: * â??bottom dead centerâ? - Digital position display - 1x freely movable foot switch - Operating instructions (PDF)

Condition: used, functionality: fully functional, For sale is a MABI 8Z dished end punch which we used as a multi-hole punch. Iisdpfxsx Dbuns Aatjf