Used Pcm Srl Coating Head for sale (13,572)

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. Njdpfjwzl Hxox Amnsct * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: PEF-2.5 PULVER EINBRENNOFEN ELEKTRISCH, temperature: 230 °C, heating capacity: 30 kW (40.79 HP), inner dimension length: 2,500 mm, inner dimension width: 1,505 mm, ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 6 weeks after receipt of payment! ✅✅✅Energy Class A+++✅✅✅ ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✳️ Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ ⭐ Powder furnace with electric heating - ✔️ Internal dimensions: 2500 mm L * 1505 mm W * 1800 mm H ✔️ Electric heating output: 30 kW/h ✔️ Fan: 3000 m3/h 80 mm SS ✔️ Circulation fan output: 1.5 kW/h ✔️ Total 35 kW/h +- 10% ✔️ Digital heat control, continuously adjustable temperature up to 220°C ✔️ Sandwich panels inside: 1.5 mm galvanized steel, outside: 1.5 mm powder-coated Steel Ncedpfx Amowfgbronet ✔️ Adjustable curing temperature, curing time, and exhaust fan function ✔️ An audible signal sounds at the end of the curing time ✔️ Insulated door with special locking systems (snap lock) ✔️ Insulation: 150 mm (150 mm rock wool) 🔥 PEF-2.5 Curing Oven: Your versatile industrial oven for drying and curing processes! 🔥 Whether powder coating, wet paint, plastic processing, or other thermal processes – the powder curing oven is your reliable solution for professional curing and drying processes up to 230°C! 🌡️ _____ 🚚 Maximum loading flexibility • Compatible with ceiling rail systems • Optionally with insert shelf system for small batches _____ ⚙️ Intelligent control – just the way you need it ✅ PID control (optional) for precise temperature control ✅ Touchscreen control panel & smartphone control 📱 (optional) ✅ Weekly & monthly reports at the touch of a button (optional) ✅ Timer function: freely programmable from 10 minutes to 24 hours ⏲️ ✅ Automatic shutdown after the end of the process _____ ♨️ Ramp heating mode (optional) Precisely control temperature progression and holding times, e.g. E.g.: • Reach target temperature within a defined time • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events _____ 🛡️ Safety is our priority 🟢 Safety sensors to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume removal via automatic venting _____ ⚡ Customized energy and heating system 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) _____ 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. _____ 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! _____ ☀️ 2-YEAR WARRANTY ☀️ Request more information

Year of construction: 2001, condition: used, Slitter rewinder with a working width of 520 mm, maximum parent roll diameter of 1000 mm. Features 2 unwind shafts with a diameter of 70 mm, suitable for producing double-layer or single-layer rolls using a single unwinder. Equipped with 9 pneumatic knife holders, minimum slit width of 30 mm. Rewind shafts available in 25.4 mm, 50.8 mm, and 70 mm diameters. Finished roll maximum diameter 400 mm; suitable for offset paper and siliconized label paper. Maximum speed 150 m/min. Dimensions: length 3.5 m, width 1.2 m, height 1.5 m. Nedsyk T Izjpfx Amnoct

Condition: new, Year of construction: 2025, total height: 982 mm, total length: 4,000 mm, total width: 1,100 mm, volume flow: 18,000 m³/h, warranty duration: 12 months, Extraction wall with 18,000 m3/h Max. power consumption 5 kW/h Electric motor 4 kW Nsdpfx Aewz Ic Nemnoct Air unit 18,000 m3/h Nicotra ADH 400 The full description can be found in the attachment to this listing.

Condition: new, Powder Coating Systems For years, powder coating has been continuously evolving as an alternative to wet painting, and it has recently gained increasing importance due to its lower environmental impact—specifically the absence of solvents and paint sludge. Powder recovery further boosts the efficiency of these systems to a particularly high level. For users, powder coating offers the advantage of creating an extremely durable and corrosion-resistant surface that is significantly more impact-resistant than what traditional painting can achieve. Additionally, post-processing tasks such as grinding or drilling the powder-coated parts present no problems, as the coating will not chip off. Pony Luxury Coating powder coating systems provide you with tangible advantages: they are efficient, environmentally friendly, and—as always—unsurpassed in flexibility. We achieve this through a range of system types. Manual Powder Coating Systems Ncsdexa Hzxopfx Amnot Manual coating systems are the ideal solution for complex and demanding workpieces. Thanks to skilled operators, these systems offer continuous adaptation to changing conditions and varying product sizes. Flexibility is paramount—with the added benefit of an attractive entry price into the world of powder coating. Large-Scale Powder Spray Booths No matter how large or challenging your workpieces, our systems are larger! In the commercial vehicle and utility sector, where components are exposed to significant stress, powder coating has established itself as the ideal solution. To accommodate ever-larger components, we offer our large-scale powder booth, which supports unlimited manual coating, and, when combined with a conveyor system, handles any workpiece size with ease. Automatic Powder Coating Systems If your operation requires high throughput and rapid processing, an automated powder system is the way forward. Coupled with a conveyor, light barriers allow precise detection and, consequently, exact powder dosage to ensure maximum efficiency. The system can also be equipped with lifting stations and robots to handle even the most complex components. Powder Curing Ovens & Flash-Off Dryers These provide the perfect finishing touch to powder coating: the curing oven. Our ovens feature the highest insulation class, ensuring consistent, high efficiency. Detailed temperature control also enables use as a flash-off dryer to dry substrates after pre-treatment. Temperatures up to 250 degrees Celsius are possible, which allows usage as a tempering oven, for instance with hot-dip galvanized materials. Of course, typical use as a powder curing oven is straightforward. Optimal air distribution and a visualized control panel prevent over-baking, and even allow multiple color shades to be cured in a single process. Do you have questions or suggestions? We are happy to assist you!

Condition: new, Equipment: cabin, Stationary small parts spray booth Dixi █████ Achieve perfect and uniform coating of small parts. The extraction system ensures optimal results even in the smallest spaces. Optionally equipped with a turntable or a wheel holder, as well as a compact yet powerful extraction unit, it is perfectly suited for processing small workpieces and wheels. The side panels effectively limit the distribution of overspray, allowing work to be carried out in confined spaces without contaminating surrounding areas. Integrated lighting is also available as an option. Additionally, thanks to its low weight and minimal connections, the booth can be relocated to a new site in no time, ensuring your flexibility at all times. The system comes fully pre-assembled and ready for immediate use. Your Benefits Thanks to its compact design, flexible dimensions, and versatile accessories, this booth offers a broad range of applications. The sophisticated modular system requires minimal space and is therefore suitable for use in virtually any premises. Different filter media and stages enable highly efficient operation, while filter changes can be performed in just a few minutes. Application and Safety Processing of both water-based and solvent-based coating materials is enabled by the use of ATEX-certified explosion-proof motors. Nodpfsxa Hx Rex Amnoct It can also optionally be used for spraying adhesives. The large filter surface ensures uniform extraction throughout the process.

Condition: new, Year of construction: 2024, functionality: fully functional, total length: 3,400 mm, total height: 2,210 mm, total width: 1,505 mm, type of input current: three-phase, warranty duration: 24 months, temperature: 250 °C, heating capacity: 30 kW (40.79 HP), inner dimension length: 2,500 mm, Equipment: emergency stop, ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 6 weeks after receipt of payment! ✅✅✅Energy Class A+++✅✅✅ ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✳️ Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ PEF-2.5 ELECTRIC POWDER FIRING OVEN WIDTH (INTERIOR): 1,505 mm HEIGHT: 1,800 mm (from the air duct) LENGTH (INTERIOR): 2,500 mm ➢ The thermoblock unit measures 785 x 1,800 x 2,210 mm. The heating capacity is 30 kW/h. A circulating fan is 1.5 kW/h (1 pc.), and an exhaust fan is 0.54 kW/h. ➢ Double-leaf door with thermal insulation and silicone seal. ➢ Guide rails are manufactured for trolleys in the dimensions indicated on the floor panels. ➢ Specially designed air duct ensures uniform air distribution in the curing oven. ➢ The electrical switchgear is made of Siemens and Schineider. This curing oven does not have a PLC system. PLC is available as an option. ➢ Curing temperature, curing time, and heating unit function are adjustable. At the end of the program, an audible and light signal is emitted by the buzzer. ➢ Additionally, a product transport cart with cast wheels is located inside the oven. 2. PKF-4 POWDER COATING BOOTH ➢ DIMENSIONS: 800x1930x2200mm (dimensions including fan) Nsdpfx Amswdtfujnect ➢ Teflon filters: 4 pcs. ➢ Filter suction fans: 4 kW x 1 pc. (6,000 m3/h – 200 mm SS) ➢ 36 W LED lighting x 1 pc. ➢ Bottom drawer x 1 pc. ➢ Control panel for controlling air intake and pressure blasting ➢ DELTA frequency converter ➢ Heavy-duty rollers under the paint booth. ➢ An additional filter is located at the fan outlet. ♨️ Ramp heating mode (optional) Precisely control temperature progression and dwell times, e.g. E.g.: • Reach target temperature within a defined time • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events _____ 🛡️ Safety is our priority 🟢 Safety sensors to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume removal via automatic venting _____ ⚡ Customized energy and heating system 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) _____ 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. _____ 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! _____ ☀️ 2-YEAR WARRANTY ☀️ Request more information

Condition: new, Year of construction: 2024, functionality: fully functional, ⚡️ Top Service ⚡️ Fast Delivery ⚡️ Excellent Support! ✈️ Price includes shipping within Germany – No additional transport costs! ✈️ Fast delivery: Only 6 weeks after receipt of payment! PROFESSIONAL POWDER COATING HAS NEVER BEEN THIS EASY! Looking to expand your business and enter the world of professional powder coating? The PEF2.5+ is the perfect solution for beginners! This high-performance system allows efficient, cost-effective, and high-quality coating of car rims and smaller workpieces – with minimal effort! ✨UNBEATABLE PROMOTION – ONLY UNTIL THE END OF MAY!✨ Take advantage of this limited-time offer before it's too late! PONY Luxury Coating – QUALITY THAT CONVINCES! ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✅ 100% European manufacturing – No China products, only top quality built to European standards! ✅ Modular & expandable – Additional options for greater performance and flexibility! ✅ All spare parts included – Long-term use with no hidden extra costs! ✳️Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today. ✳️ ✨✨Buy directly from the manufacturer and secure price and quality advantages!✨✨ ☘️Environmentally friendly☘️⚡️Green Energy⚡️☘️ Powder oven + powder booth + powder gun Complete Starter Package PEF2.5+ ⭐ Powder oven with electric heating ✔️ INTERNAL WIDTH: 1,505mm ✔️ HEIGHT: 1,800mm (from air duct) ✔️ INTERNAL LENGTH: 2,500mm ✔️ Thermoblock unit dimensions: 785x1800x2210mm; heating capacity is 30 kW/h; recirculation fan is 1.5kW/h – 1 pc.; exhaust fan is 0.54kW/h. ✔️ Double-wing door with thermal insulation and silicone seal. ✔️ Guide rails for rack trolleys are manufactured according to the dimensions specified on the base plates. ✔️ Specially designed air duct for homogeneous air distribution inside the curing oven. ✔️ Electrical panel materials by Siemens and Schneider. This curing oven does not include a PLC system. PLC is available as an option. ✔️ Curing temperature, curing time, and heater unit function are adjustable. At the end of the program, an alarm and light signal from the buzzer will indicate completion. ✔️ Additionally, a product transport trolley with cast wheels is located inside the oven. ⭐ Powder coating booth ✔️ Dimensions: 800x1930x2200mm (including fan) ✔️ Teflon filters: 4 pcs. ➢ Filter suction fan: 4kW x 1 pc. (6,000m3/h – 200mmSS) ✔️ 36W LED lighting x 1 pc. ✔️ Bottom drawer x 1 pc. ✔️ Control panel for air intake and powder spray regulation ✔️ DELTA frequency converter Ncjdswfhu Hjpfx Amnot ✔️ Heavy-duty rollers under the coating booth ✔️ Additional filter at the fan outlet ⭐ Powder coating gun E-Coat+3 Master with Multicolor (vibration table) Enquire now – Get your business ready for the future! ☀️ 2-YEAR WARRANTY ☀️ ☀️All our machines are CE-certified and necessary machines have ATEX certificates.☀️

Year of construction: 2004, condition: reconditioned (used), functionality: fully functional, machine/vehicle number: 40EV.118, Twin-screw extruder model EBC 40HT/37D Screw diameter: 42mm Main motor power: 51kW L/D: 37 Center distance: 35mm The extruder consists of a machine base, reduction gearbox, and a distribution gearbox equipped with special bearings capable of ensuring perfect operation with a backpressure of up to 150 bar. The barrel is a modular cylindrical type, with a length equivalent to 37 screw diameters, divided into eight sections. Temperature regulation of each barrel module is achieved by forced circulation of demineralized water through a series of horizontally drilled holes in each module. Heating is provided by cartridge heaters. The screws are made up of interchangeable segments and are mounted on splined shafts, allowing for the configuration best suited to the required processing. Ncedpfxeyg Egho Amnst Barrels and screws are manufactured from highly wear-resistant steel. The degassing system consists of a 1.5kW liquid ring vacuum pump connected to the dedicated module by easy-to-clean piping; extracted gases are condensed in a special container for easy cleaning. The drive system features a (Siemens) 51kW AC motor with an inverter, enclosed in an electrical cabinet equipped with appropriate safety features and control signals. The control panel (integrated into the extruder) is divided into two sections: power, and temperature control. The cabinet is equipped with an air-conditioning unit. The extruder comes with a closed-loop water/water temperature control unit (1.1kW pump). Chiller not included.

Year of construction: 2023, condition: new, APPLICATIONS: - Paving manufacture - Curb manufacture - Concrete block manufacture for: - masonry - foundation - posts - floor slabs - chimneys - scafa gutters - roadway gutter covers ADVANTEGES: - Vibrators on tamper head. - Bunker and drawer for finishing layer of paving and kerbs. - High productivity - active area 1,10 x 0,6m - Automatic operation: PLC (Mitsubishi Electric) logic programmer + touch display + software for automatic machine operation; Schneider Electric electrical command and control components - Our wide range of moulds can ensure a diversified production. - Reliable mechanical and hydraulic systems. COMPONENTS: - Press unit - Pallet space - Pallet feeding line - Hopper and drawer (1) for feeding the mould with concrete - Hopper and drawer (2) for making the finishing layer (paving, kerbs) - Pallet discharge line with freshly moulded products - Hydraulic unit - Electrical control panel with PLC. Nodpsht Uwpsfx Amnsct TECHNICAL FEATURES: - Pallet dimensions: 1240x750x45mm - Useful surface: 1100x630mm - Minimum/maximum finished product height: 40mm/ 250mm - Vibration frequency: 3000rpm - Cycle time: 35 - 60 seconds - Total Installed power: 30,00 kW MAIN DIMENSIONS : - Width: 2,10m (without hydraulic unit and control panel) - Length: 8,00m - Height: 3,10m - The hydraulic unit and control panel are placed at the side, at a distance of 1.00m from the chassis and occupy a surface area of 2m2. - Machine mass 6,000 kg

Year of construction: 2022, condition: like new (used), Machine for printing QR codes and applying hologram patches, customization of labels or roll-fed paper support. Performs hot stamping of customized hologram or transparent foil onto the QR code, enabling immediate verification via reader device with IOS or Android software. Ncodpfx Ameygku Renet

Condition: used, Year of construction: 2023, New PET filling monoblock for CSD up to 15000 bph System Overview: The “Unibloc 50 50 10” model by UBL SRL is an integrated bottling system, designed to operate with a maximum capacity of 15000 BPH. Its architecture combines three main functions: rinsing, filling and closing in a single monobloc. Rotary Rinse in the New filling monoblock for CSD: The rinsing section includes 50 heads, configured to process PET bottles. The design allows for effective and rapid washing, essential for maintaining hygiene standards. Counterpressure Filling: The filling module uses 50 isobaric valves to ensure uniform and precise filling. The isobaric system is particularly advantageous for carbonated drinks such as soft drinks and sparkling water, minimizing the loss of CO2 during filling. Screw Closure: The sealing section is equipped with 10 rotary heads for applying plastic screw caps. This mechanism ensures reliable and consistent closure, operating clockwise for greater efficiency. Control and Automation: The monoblock is equipped with a PLC/HMI control system produced by Schneider, which allows precise and facilitated management of the process. The integration of an electronic BPM meter and flow sensors at the inlet and outlet further improves operational efficiency. Configuration and Adaptability: The system is configured to handle 500ml PET bottles, but its construction allows modifications to accommodate various bottle sizes. This flexibility is essential for businesses that operate with different products and container formats. Safety and Construction of the New filling monoblock for CSD: Ncodjvgt U Aepfx Amnet The design includes a stainless steel safety hood, ensuring operator safety and compliance with current regulations. Technical Conclusion: The “New PET filling monoblock for CSD up to 15000 bph” is a complex and highly technological system, designed to maximize efficiency in bottling drinks in PET bottles. Its technical characteristics, from production capacity to automation solutions, make it an indispensable tool for companies seeking precision, reliability and adaptability in the bottling process.

Year of construction: 2010, condition: used, Imperia D (85 x 105 cm), year of manufacture 2010, CE 2010 Machine reinforced at connecting rods Micrometric pressure adjustment Nsdpoxa Epnjfx Amnect Weight: 6,000 kg Mechanical speed: 1,200 sheets/hour Machine inspected by manufacturer, safety devices optimized With hardened cutting plate Self-centering universal frame Operator arm with control panel Refurbished pneumatic brake-clutch system Delivery time: 60 days Price: on request Warranty: 3 months

Condition: like new (used), Year of construction: 2023, operating hours: 30 h, functionality: fully functional, machine/vehicle number: 161625, total width: 2,450 mm, total length: 7,400 mm, total height: 3,000 mm, maximum load weight: 100 kg, heating capacity: 32 kW (43.51 HP), tank capacity: 280 l, warranty duration: 12 months, type of input current: three-phase, compressed air connection: 6 bar, input voltage: 380 V, input frequency: 50 Hz, year of last overhaul: 2024, Equipment: CE marking, Ultrasonic automatic cleaning plant with versatile cycle: Charge by operator Precleaning tank Ultrasonic cleaning Rinsing in cold water Ultrasonic cleaning Ncsdpfx Amexlhvnjnst Rinsing in cold water Protection in demi warm water Drying in hot air

Condition: like new (used), Year of construction: 2025, operating hours: 15 h, functionality: fully functional, machine/vehicle number: 100925, total width: 900 mm, total length: 1,600 mm, total height: 1,900 mm, maximum load weight: 200 kg, heating capacity: 12 kW (16.32 HP), tank capacity: 600 l, warranty duration: 12 months, type of input current: three-phase, inner dimension height: 500 mm, inner dimension length: 1,200 mm, inner dimension width: 600 mm, input voltage: 380 V, input frequency: 50 Hz, year of last overhaul: 2025, power: 12 kW (16.32 HP), operating pressure: 6 bar, Equipment: CE marking, documentation/manual, Ultrasonic cleaning machine with a pneumatic platform Pieces to be cleaned besides ultrasonic action are continuously moved up/down so that to increase the result All controls for safety working are automatized by PLC Maximal insulation and insonorization against ultrasonic noise Usefull platform dimensions: mm. 1.200 x 600, maximal piece height: mm. 500 Nsdpexxvk Tsfx Amnect Full stainless steel AISI 304

Condition: like new (used), Year of construction: 2025, operating hours: 15 h, functionality: fully functional, machine/vehicle number: 100925, total width: 900 mm, total length: 1,600 mm, total height: 1,900 mm, maximum load weight: 200 kg, heating capacity: 12 kW (16.32 HP), tank capacity: 600 l, warranty duration: 12 months, type of input current: three-phase, inner dimension height: 500 mm, inner dimension length: 1,200 mm, inner dimension width: 600 mm, input voltage: 380 V, input frequency: 50 Hz, year of last overhaul: 2025, power: 12 kW (16.32 HP), operating pressure: 6 bar, Equipment: CE marking, documentation/manual, Ultrasonic cleaning machine with a pneumatic platform Pieces to be cleaned besides ultrasonic action are continuously moved up/down so that to increase the result All controls for safety working are automatized by PLC Maximal insulation and insonorization against ultrasonic noise Ncjdpfjxmhckox Amnet Usefull platform dimensions: mm. 1.200 x 600, maximal piece height: mm. 500 Full stainless steel AISI 304

Condition: new, Year of construction: 2025, operating hours: 4 h, functionality: fully functional, machine/vehicle number: 281225, total width: 900 mm, total length: 4,500 mm, total height: 2,500 mm, heating capacity: 12 kW (16.32 HP), warranty duration: 12 months, type of input current: three-phase, inner dimension height: 400 mm, inner dimension length: 600 mm, inner dimension width: 500 mm, compressed air connection: 6 bar, input voltage: 380 V, input frequency: 50 Hz, year of last overhaul: 2025, Equipment: CE marking, Robotic multi-stage ultrasonic washing machine Useful internal tank dimensions: mm 600 x 500 x 350h Usable tank capacity: 100 liters Supplied baskets: mm 550x400x280h Ultrasonic power: 3000 watts Ultrasonic frequency: 33 kHz PZT elements: 32 Heating: 16 kW (4+4+4+4) Voltage: 380V, three-phase, 50 Hz Power consumption: 14A Load per basket: 8 kg PLC for detergent liquid level, temperature and ultrasonic power control Full noise insulation Insulation with volcanic rock wool Entire construction in AISI 304 stainless steel Tank sheet thickness: 2 mm (20/10) WORK CYCLE - Loading of baskets onto motorized platform Ncodjxv U Ifspfx Amnet - Pre-wash with hot detergent - Washing with ULTRASOUND - Rinsing with hot running water - Washing with ULTRASOUND - Rinsing with hot running water - Protection in special cold or hot liquid - Drying with heated and ventilated air - Unloading of basket onto motorized platform

Condition: reconditioned (used), Year of construction: 2006, BACCIOTTINI Group Pit Stop AF Speed, year 2006: automatic creasing and perforating machine in excellent condition. The machine will be overhauled at Bacciottini Group srl's facilities. Robust construction and reliable performance. The machine is equipped with a NEW standard V-Shape creasing kit and a 100 cm extension. All other optional tools currently available can be added: digital creasing kit, standard perforating kit (2/1, 3/1, 4/1), or micro-perforation kit. Technical specifications: - Maximum format: 50 x 70 cm (50 x 100 cm with extension) - Minimum format: 8 x 15 cm Ncsdpfx Aeyk Utxemnot - Paper weight: from 80 to 600 gsm - Minimum creasing distance: 0.1 mm - Programming: 200 programs with 100 creases per program - Power supply: 400 Volt three-phase 50 Hz - Power requirement: 3.5 kW This has been our best-selling model for years and continues to be appreciated worldwide for its quality and reliability. The attached photos are from our catalogue and do not specifically refer to the machine being offered.

Year of construction: 2005, condition: as good as new (ex-display), ACCEPTANCE OF SELF feed head is held on the guides of hardened cylindrical surface and additionally treated grinding. Three-phase motor power 3HP 2800 rpm / min. Output frontal saw blades with cutting heads. Feed discs cost of delivery cover customer Startup type Ncodpfsb Rnv Sjx Amnet negotiated Description Notes Saw 2 a head for precision cutting of aluminum profiles GAMMA. Precise double miter saw for serial production of blanks at an angle of 90 ° and 45 °. Convenient and safe execution of multiple cutting operations. Automatic positioning of the moving cutting head. Automatic positioning of the moving cutting head. Adjustable stroke discs. The angles of inclination of the cutting head 45 °, 90 °, easy pneumatically. Intermediate angles are adjusted manually using the bumper and angular scale. LENGTH OF CUT = 4000 5220 x 1390 x 1460 mm Weight 1200 kg.

Condition: excellent (used), Year of construction: 2016, Steton 5-head four-sided planer. Ncodpfxoi Apuhe Amnst Steton 5-head four-sided planer. The machine after the review does not require a financial contribution. Technical data: - max width of the workpiece 23 cm - max height 13 cm spindle diameter 40mm - 1 - Horizontal bottom 23 cm - 2 - vertical right 13 cm - 3 - vertical left 13 cm - 4 - horizontal upper 23 cm - 5 - universal 360 degree soundproofing cabin - electric setting of planing thickness - two types of feed speed

Condition: like new (used), Year of construction: 2020, operating hours: 50 h, machine/vehicle number: LW250*1000, Decanter centrifuge manufactured in 2020, but put into operation in May 2021! The machine is in like new condition (used in total approx. 50 operating hours)! The decanter is for sale due to a change in technology, it works flawlessly! Manufacturer: YIXING HEAD SEPARATOR MACHINERY CO. LTD., CHINA Year of manufacturing date: 2020 Serial Number: LW250*1000 Machine signal: 02-001 Ncedpfxspu A D Aj Amnjt Decanter indication number: 2647 Sludge formation capacity of decanter: 500 kg/h Main motor capacity: 7,5 KW Vice motor capacity: 3 KW Capacity: 1-5 m3/h Netto weight of decanter: 1000 kg Material of wetted parts:1.4404 Feed volume flow: 0,5t – 3t/h Stainless steel Reference number: 2590

Condition: new, Year of construction: 2021, functionality: fully functional, machine/vehicle number: 21011109, total height: 1,200 mm, construction height: 1,200 mm, lifting height: 5,100 mm, empty load weight: 4,700 kg, load capacity: 3,000 kg, overall weight: 4,700 kg, total length: 5,000 mm, total width: 2,500 mm, table width: 2,500 mm, input voltage: 400 V, type of input current: AC, platform width: 2,500 mm, power: 4 kW (5.44 HP), New machine never used, very sturdy construction, available immediately. Complete with clarification of conformity issued by the manufacturer. Nedpfx Amjudi D Nsnsct

Condition: used, Year of construction: 2002, machine/vehicle number: 19711, functionality: fully functional, power: 4.5 kW (6.12 HP), cutting height (max.): 2,200 mm, saw blade diameter: 294 mm, overall weight: 1,050 kg, cutting length (max.): 5,300 mm, collet bore: 30 mm, The vertical panel saw features a solid and compact structure to ensure stability during operation. This configuration allows for consistently high cutting quality, even on large or particularly challenging materials, delivering smooth and linear movements for safe and efficient work. The machine is supplied with 29 blades, each with 50% remaining service life. Nedpfxowqmyro Amnect Transport not included.

Condition: new, functionality: fully functional, Year of construction: 2025, operating hours: 0 h, machine/vehicle number: plate roll, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: MG EVO, controller model: EVO 4 AXIS, number of rollers: 4, roller (bottom) diameter: 140 mm, roller (top) diameter: 160 mm, side roll diameter: 150 mm, roller diameter: 200 mm, roller length: 2,050 mm, working width: 2,000 mm, working height: 700 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 6 mm, sheet thickness aluminum (max.): 6 mm, overall weight: 2,200 kg, total length: 3,200 mm, total width: 1,100 mm, total height: 1,200 mm, power: 4 kW (5.44 HP), input voltage: 400 V, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, 4 ROLL BRAND MG ITALY, HYDRAULIC MODEL M2006P EVO_CNC PLATE BENDING ROLL PLANETARY DESIGN DOUBLE PINCH PRE-BENDING CNC_EVO PROGRAMMABLE AUTOCALCULATION AUTOMATIC PLATE ROLLING Capacity: -Width of plate: 2000 mm -Thickness of plate rolling 6 mm -Thickness of plate pre-bending 4 mm Rolls -useful width mm. 2050 -Top roll mm. 160 - Lower roll mm. 140 Configuration installed: • Surface hardening of the four rolls, smooth finishing suitable for stainless plates rolling • Dual pre-pinch, with adjustable force upon the input of plate thickness • Conical bending hydraulic attachment - hardened contrast pad. • Power driven rolls rotation top/bottom gearbox axial direct drive hydraulic each roll. • Calibration system for re-rolling of welded shells rounding. • Console electric independent with centralized commands joysticks and CNC screen readout. • CNC controller on touch screen 15” , CAD/CAM interface 4 axis auto calculation software package. with digital readout of the axis for use in manual rolling, semiautomatic and fully automatic programmable. Njdpfx Amjw Dnd Sonsct • Opening front side hydraulic drop-end to unload closed shells. • Variable working speed step-less axis interpolation. • Safety installation with emergency stop. • Instruction manuals for operation and service.

Condition: new, NEW machine, end-of-series Pit Stop D2H HIGH SPEED double-head creasing and perforating machine, equipped with 2 standard creasing kits (for Head A and Head B) and mobile wheels. The second head, unlike the first, operates from bottom to top. All creasing and perforating tools can be installed on this second head. This allows creasing and perforating to be performed in a single pass; or, by fitting two creasing tools, it is possible to perform creases from both the top and the bottom in one pass, ensuring the correct crease orientation for zig-zag folding. High-performance creasing machine with a maximum output of up to 14,000 sheets per hour. Easy-to-use controls allow for up to 100 creases or perforations per sheet and a memory capacity of up to 200 jobs. The machine can crease, perforate, and punch, making it ideal for WIRE-O binding and calendar production. This end-of-series machine can be equipped with the following optional tools: - Digital creasing kit (for both Head A and Head B) - Perforation kit 2/1-3/1-4/1 (for both Head A and Head B) - Micro-perforation kit (for both Head A and Head B) - 100 cm extension - Punching kit in various sizes Nsdpexmhflefx Amnect Technical data: Min./max. sheet size: 8×10 cm / 50×70 cm (with optional extension 50×100 cm) Paper weight: 80 to 600 g/m² Programming: 200 programs (100 operations per program) Minimum crease distance: 0.1 mm Production speed in A4: 14,000 sheets/hour (with 1 crease) Power supply: 400 Volt three-phase + neutral, 50 Hz