Paper Making Machine

Condition: used, Year of construction: 2003, Offset 6 color with coating Roland 706/3B+LTTLV (UV) Year: 2003 Number of impressions (mio): 500 Machine control - RCI - IntelliTrax II density control Feeder - Non-Stop feeder - Logistic system in feeder Printing units - Number of printing unit(s): 6 - Straight machine - APL Full Automatic Plate Change - Automatic blanket washing device Psdpfxouhtg Ae Aa Eerf - Cooling system: Technotrans - Ink temperature control Coating - Number of coating unit(s): 2 - Number of transfer unit(s): 2 - Tresu chambered ductor blade system - Number of Anilox roller(s): 2 Drying - IR dryer between coating unit 1 and 2 - IR + hot-air dryer in delivery - UV dryer in delivery: Eltosch Delivery - Non-Stop delivery - Powder spray: Grafix Cantronic 3000 - Logistic system in delivery Elevation - Machine raised by (cm): 50 Accessories - Air cabinet: Becker - Cabinets air cooled - Compressed air compressor, excluded

Condition: excellent (used), Year of construction: 2016, operating hours: 27 h, SBL 1060 SE Year: 2016 Sheet feeder: Manual non-stop pile feeder Material range: Paper and board from 470 × 350 mm to 1060 × 760 mm Max cutting format: 1050 × 740 mm Psdswypp Iepfx Aa Eerf Min sheet size: 470 × 350 mm Max sheet size: 1060 × 760 mm Max cutting pressure: 300 tons Material thickness: 0.1 – 2 mm (corrugated/laminated max 4 mm) Min gripper margin: 9.5 mm Max inside chase size: 1155 × 852 mm Cutting plate size: 1076 × 756 mm Max speed: 8,000 sheets/hour Power consumption: Total 32 kW (22 kW + 10 kW for lower plate heating) Machine dimensions (L×W×H): 5,900 × 5,700 × 2,615 mm Max pile height – feeder (with pallet): 1,750 mm Max pile height – delivery (with pallet): 1,450 mm Feeder Section - Pneumatic feeder table - Non-stop manual feeder system - Anti-static system - Pre-pile device - Manual suction group adjustment - Micrometric suction adjustment - Motorized side pile adjustment - Suction belt feeder table - High-pressure lubrication pump - 2 pneumatic side register guides - Electronic control of front and side register Cutting/Embossing Section - Automatic pressure adjustment up to 300 tons - Preparation and introduction table for die frames in platen - 2 quick-lock die chase frames with bottom plate - Pneumatic locking of the chase and lower supporting plate - Centerline System - Micrometric system - Heated lower support plate (24 mm) - Cutting plate: 4 mm - Compensation plate: 3 mm - Archiveable 1 mm thin cutting plate Stripping Section - Quick lock for upper and central stripper frames - 2 standard upper stripper frames - 2 standard lower stripper frames - Double accessory kit for lower stripper prep (pins, bars, clamps, etc.) Delivery Section - High-pile automatic non-stop delivery with conveyor - Guillotine for automatic removal of gripper margin waste - Sheet deceleration device - Tab insertion device

Condition: like new (used), set, packed in wooden box, screw and barrel for 150 mm extruder, Prodpfxodm Agho Aa Esf grooved feeding bush, screw with shearing and mixing element

Year of construction: 2012, condition: used, pasteurizer with pipe heat exchanger 600 l/h (up to 80°C) with automatic control storage tank for BiB with level control Psdpfx As Hnnhea Esrf BaginBox filler with flow meter oil boiler 50kW mounted on braked trailer with tarpaulin max. weight: 1350 kg

Year of construction: 1963, condition: used, functionality: limited functionality, machine/vehicle number: 512804, 1963 Bobst SP900E with double action stripper in reasonable/good condition. Well-maintained.. in recent years for example sprocket wheels, main gripper chains, counterplate under cuttingplate, cardan joints to the feeding head, have been renewed (original Bobst parts) Gripperbars have not been renewed recently, they are still in quite a good condition. The knee joints have almost no signs of wear. they were probably at some point and the machine has not been used much since then. There is hardly any screech on them. Machine is dismantled in our storage in the South of The Netherlands, dismantled and not under power. For seriously interested potential buyers we will further upgrade the machine and assemble it and give the possibility to test it inevery way they want. In that case price will be 22,000 euros, loaded on to your transport, EX SITE Psdjtyqizjpfx Aa Eorf

Year of construction: 2022, condition: new, This system operates in automatic mode. The transfer of pallets between production line and curing area is carried out by Finger Car. 1 operator supervises the production process via control panel equipped with 4 different monitor, pc system. Automation system software has user-friendly interface and can be translated into customer’s preferred language. Production line requires the construction of curing chambers with racks. Steam curing is recommended for working in one shift and is mandatory for working in two shifts. Prjdpfxsibcyco Aa Esf Transfer of production pallets with green products to the curing chambers as well as the transfer of pallets with cured products to the cubing station is carried out by automatic pallet transport system known as Finger Car. Finger car consists of lower and upper electric trolleys, which move along a set of rails built perpendicularly to the concrete block production line. The upper trolley has steel forks for grabbing and holding pallets. It transfers concrete products to the curing chambers, going inside each chamber to place pallets with wet products on racks to cure. On its way back it takes a stack of pallets with cured products and loads it into the lowerator. The price given as 1.200.000 USD includes all the machine equipments, concrete batching plant and 3000 pallet rack system. It is very special offer for August 2022!

Condition: used, Year of construction: 2005, Saddle stitcher Heidelberg Stitchmaster ST 400 Year 2005 Operation / Control - Colour monitor Feeders - Number of chain stations: 9 - Horizontal signature feeders: 2 x TAL 400 - Vertical signature feeders: 6 x TAS 400 - Cover feeder: UFA 400 - Excluding pump(s) Stitching unit Heidelberg Stitchmaster ST 400 - Thickness control Podpfx Aaoh E Ewdj Ejrf - Stitching heads: 2 - Delivery to the left - Reject gate, for incomplete products Trimmer Heidelberg TR 400 - Sets of knives: 2 Delivery Heidelberg CHA - Compensating stacker - Delivery to the left

Condition: used, Year of construction: 2000, greates pass round over bed 520 mm swing diameter over bed slide 480 mm turning length 3000 mm control 840 D SIEMENS number of tools 12 Driven tools - quantity 6 spindle bore 103 mm c-axis ja 0 Scope of delivery of the basic machine: SINUMERIK 840 D 3 controlled axes Rotation Ø over bed 520 mm Turning Ø over bed slide 480 mm Tool carrier with 12 cylindrical shank holders Ø 50 mm 1-stage AC main drive, 53 kW, 50 % ED Speed range 30 - 3000 min-¹ Main spindle head size 8 Clamping door for clamping devices chip conveyor THREE-DIMENSION 3000 mm 12 cylindrical shank holders DIN 69880-50x78 of which 6 positions can be equipped with driven tools, Power 6 kW at 60 % ED, speed range 20-2500 min-¹ 2 gear stages Pedpfx Ajwp S Sqoa Eorf C-AXLE Speed range 0-20 min-¹ Max. Angle specification 9999.999° Working range according to work area diagram POWER CHUCK 3 NHF 315-82 A8 FABR. FORKARDT with centrifugal force compensation, Outer Ø 315 mm, bore Ø 82 mm, with hard top jaws, ground, rod material Ø max. 63 mm including draw tube and attachment

Condition: good (used), Year of construction: 2000, GALLUS ARSOMA EM 510 – 3-color Technical Specifications: • Model: Gallus Arsoma EM 510 • Year of Manufacture: 2000 • Web Width: 510mm • Printing Units: 3 x UV FLEXO UNITS or 2+1 (backside) printing possible • Die cutting units: 1 • UV drying: Included Predpfx Aaswmfyie Esf • Web Turnbar (Turner Bar): Included • Web Cleaning: Included • Roll-to-Sheet Conversion:Included • Unwinder: Included • Rewinder: Included • Chiller: Included • Web Guiding System: Included Accessories Included: • Magnetic Cylinders: Included • Printing Cylinders: Included • Anilox Rollers: Included • Condition: Regularly serviced and well-maintained _____ Technical and Optical Condition: • Technical: 8/10 (checked and in excellent running condition) • Optical: 8/10 (cleaned and ready for immediate end-user deployment) _____

Condition: like new (used), Year of construction: 1990, functionality: fully functional, BOBST AUTOMATIC FOLDER & GLUER MACHINE • TYPE : DOMINO 100-M Predpfxovm Atbe Aa Eef • SIZE : 100 CM • LOCATION : Our Warehouse in Venlo-Netherlands Details: Full revised in 2022 3 point glueing “NORDSON” Cold Glueing System "ERO" Glueing System 2025 (Optional) “KQ” Glueing System 2025 (Optional) With standart equipments Regularly maintained by Bobst It is completely cleaned and painted It is in perfect condition Available immediately