Cylindrical Grinding Machine - Universal

KELLENBERGER 1500U BEMA Advance

Condition: used, SLITTING LINE GEORG 1500x1.5x25 Main technical data Coil thickness: 0.24 – 1.5 mm Uncoiler coil weight: 25 Tn Coil width: 230 - 1500 mm Coil outer diameter: Max. 1850 mm Working speed: 200 m/min Slitting tolerance: +/- 0.125 mm Line direction: Right to left Recoiler coil weight: Max. 16 Tn 2 Slitting heads PLC: Siemens S7 1200 Gtsdpfx Aexl R A Rsfnou Cutting capacity: number of cuts with 350 MPa 24 cuts for thickness 0.25 mm 28 cuts for thickness 0.50 mm 21 cuts for thickness 0.75 mm 18 cuts for thickness 1.00 mm 15 cuts for thickness 1.25 mm 12 cuts for thickness 1.50 mm Scope of supply 1. Coil Carriage 2. Uncoiler 3. Guiding system with 2 measured edges 4. 203.2 diam. Pinch roll before shear 5. Double interlock table 6. Slitting shear:Shaft diameter: 160 mm 7. 1 off line quick change slitting head available 8. Scrap press and conveyor 9. Intermediate coil table 10. Loop Pit and covering tables 11. Strips Braking Unit 12. Motorised recoiler with hold down separator arm 13. Unloading Coil Car 14. 4 arms turnstile 15. Electrical cabinets & Control panels 16. Existing tooling 17. Existing documentation Coil thickness: 0.24 – 1.5 mm Uncoiler coil weight: 25 Tn Coil width: 230 - 1500 mm Coil outer diameter: Max. 1800 mm Working speed: 200 m/min Slitting tolerance: +/- 0.125 mm Line direction: Right to left Recoiler coil weight: Max. 16 Tn Slitting heads: 2 PLC: Siemens S7 1200 For thickness 0.25 mm: 24 cuts with 350 MPa For thickness 0.50 mm: 28 cuts with 350 MPa For thickness 0.75 mm: 21 cuts with 350 MPa For thickness 1.00 mm: 18 cuts with 350 MPa For thickness 1.25 mm: 15 cuts with 350 MPa For thickness 1.50 mm: 12 cuts with 350 MPa

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 176308, Country of manufacture: Switzerland Voltage: 400 / 380 / 50 / 3 Net weight: approx. 350 kg Dimensions: 82x85x156 cm Installed power: max 2 kVA Customs classification: 8460.3930 TECHNICAL SPECIFICATIONS GRINDING WHEEL SPINDLE UNIT Spindle speed (both rotation directions): 2,500 / 3,500 / 5,000 / 7,100 rpm Grinding wheel motor power (2,800 rpm): 0.4 HP Vertical slide stroke (linear): 100 mm Micrometric stop adjustment travel: 25 mm Micrometric stop readout accuracy: 0.01 mm WORKPIECE SPINDLE UNIT Workpiece spindle speed (both directions, continuous): 100–900 rpm Motor power: 0.2 HP Indexing plate teeth count: 120 Angular vernier reading: 20' Collet type: W-20 Horizontal travel: 100 mm Godpsw T S Sqjfx Afnetu Rapid feed per handwheel turn: 2 mm Micrometric feed per handwheel turn: 0.1 mm Micrometric feed per scale division: 0.001 mm SPINDLE HEAD SWIVEL RANGE (a) Main direction: 165° Fixed ratchet increments: every 3° Increments with micrometric screw: every 2' (b) Grinding plane: approx. 15° Stop: at 0° Cross movement range: 80 mm Micrometer travel: 25 mm Reading precision: 0.01 mm Extraction motor power (2,800 rpm): 0.25 HP All technical specifications provided without guarantee and subject to possible errors or omissions.

Year of construction: 2022, condition: as good as new (ex-display), Manipulator with hydraulic height adjustment, face plate with clamping slots and manual remote control. Height (face plate horizontal): approx. 532 - 1.132mm Lifting distance/lifting time (hydraulic): approx. s = 600mm, t = 20s Swivel range of face plate: approx. +-300°. Height (Pl.-sch.vertical axis): approx. 709mm Dimensions face plate: Ø1.200mm x 40mm, 6x clamping slots Gtedpfjfw Ah Rsx Afnsu Speed of the main axle: approx. 2.0 rpm (other Torque main axis of rotation: approx. 7,500 Nm Face plate speed: approx. 2.5 rpm Face plate torque: approx. 1,500 Nm

Condition: new, turning diameter 560 mm turning length 1910 mm swing diameter over bed slide 355 mm Swingdiameter in the bed bridge 790 mm centre height 280 mm Turning length in the bed bridge 170 mm reus 12 (25-1600) U/min tail stock MK 5 quill stroke 180 mm diameter of quill 75 mm spindle taper DIN ISO 702-2 Nr. 8 spindle bore 80 mm spindle cone MK 7 feed längs 35 / 0,059 - 1,646 m/min feed plan 35 / 0,020 - 0,573 m/min total power requirement 8,5 kW weight of the machine ca. 2560 kg dimensions of the machine ca. 3450 x 1150 x 1650 mm Fully equipped master and feed spindle lathes. TH 4215 with digital position indicator DPA 21 / 3462070 - Hardened and ground Z-axis guideway - Spindle mount Camlock DIN ISO 702-2 No. 6 - Precisely crafted slide - Hand wheels with adjustable fine scaling 0.04 / 0.02 mm - Quadruple steel holder - All guides can be adjusted using V-ledges - Adjustment range top slide ± 90° - Guaranteed concentricity of the spindle nose better than 0.015 mm - Main spindle running in oil bath - Smooth-running gear wheels, hardened and ground with 2 adjustable Precision tapered roller bearings - Hand wheels decoupled and tested according to EN 23125 - Two-channel right-left switch tested according to EN 23125 - Switch with life cycle calculation, tested according to EN ISO 13849 - All metric pitches in the range 0.2 to 14mm/rev and all Inch threads in the range of 72 - 2 threads per inch without changing the Change gears adjustable by shift lever in the control panel - Clockwise/counterclockwise rotation can be switched on the bed slide via the switching spindle - Central lubrication in bed slide - Meehanite cast base and machine bed in one piece - Lead screw cover - Emergency stop device with foot control - Safety handwheels with snap-out function in the X and Z axes - Tailstock for taper turning adjustable ± 10 mm - Tailstock quill and hand wheel with adjustable fine scaling 0.025 mm - Quick, easy and tool-free adjustment using a clamping lever - Heavily ribbed prism bed, induction hardened and precision ground cast iron - Coolant device with separate coolant tank with level indicator and oil separator; easy and complete emptying and cleaning according to DIN - LED machine lamp in the chip guard Models TH 4210D and TH 4215D with digital readout DPA21 Godjucgr Iopfx Afnetu - User-friendly membrane keyboard, splash-proof, closed andglare-free - Glass scales scope of delivery - Fixed bezel passage Ø 15 - 145 mm - Revolving bezel passage Ø 10 - 75 mm - LED machine light - Reducing sleeve MT 6 / MT 4 - Fixed center MK 4 - Change gear set - Position stop with fine adjustment - Initial filling of the machine with quality oil - Operating tool Incl. special accessory OPTIMUM three-jaw lathe chuck centrically clamping Ø 250 mm Quick change holder SWH5-B set

Condition: new, Year of construction: 2024, carrying capacity per cantilever arm: 500 kg, shelf height: 3,200 mm, total length: 2,100 mm, total height: 3,200 mm, axle spacing: 1,000 mm, load capacity per stand: 2,500 kg, Cantilever rack in hot-dip galvanized design: Scope of delivery: 3 rack stands, height 3.2 m with base section, 1.8 m usable depth (2 m total depth) 12 cantilevers with 1.8 m usable depth (for chipboard with approx. 2.1 m depth) Longitudinal and diagonal struts for 4 m rack length (distance 1.3 m) Fastening material (screws, nuts and washers) Net price: €2,490.00 plus VAT Detailed description: - Stable steel construction made of IPE profiles (screw system) - Rack height 3,200 mm Gtjdpjqt Dmyofx Afnou - Load capacity per stand 2,500 kg - Base section and cantilevers with 1,800 mm usable depth - (for 2,100 mm chipboard depth) - Cantilevers height adjustable in 100 mm increments - 4 screwable screws per stand Cantilever arms, standard (= 5 storage levels) - Load capacity per cantilever arm 500 kg - Including longitudinal and diagonal braces for 1,000 mm spacing - Shelf length = 2,100 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Made in Germany - Short delivery time Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. Delivery for stock items can take place in approx. 1 week after receipt of the order. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: good (used), Automatic ROPP Capper Make: Bertolaso Typ: Automatic ROPP (pilfer-proof) Capper Model: Alfa 110-VH40 speed: Up to 2.000 caps/hr Dimensions: L x W x H = 1.800 x 800 x 1.800 mm electric: 380 Volt – 50 Hz Gtedog Dvfwjpfx Afnju Tooling: Customer choice Features:Included cap sorting as-is or adjusted to customer needs

Condition: used, Hydraulic Guillotine Shear STEINER Type HTS 30/20 R Machine No. 315 Year of manufacture: 1982 Cutting length: 3050 mm Cutting thickness: 20 mm Backgauge: 800 mm, motorized Motor power: approx. 30 kW Power supply: 400 Volts, 50 Hz - Backgauge with ELGO positioning control - Backgauge adjustment via ball screws - SICK safety light curtain at the front as reach-in protection - 3 material support arms with ball transfers - Electric foot switch - Spare blade - Oil cooler with air heat exchanger - Very robust machine with extremely solid construction Machine footprint (L x W x H): 4650 x 2610 x 3200 mm Machine weight: 27,000 kg Transport dimensions (base machine) (L x W x H): 4650 x 2610 x 3200 mm Transport dimensions (additional) (L x W x H): 3500 x 2450 x 1400 mm Total weight: 27,000 kg Good condition Machine can be inspected at our warehouse in 37235 Hessisch Lichtenau, test cuts possible. Gtjdpod Hxx Aofx Afnju Currently, the hold-down devices are being resealed; the resulting price adjustment will be made in the coming days.

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 1845/455, Completely refurbished: Mechanics, geometry, hydraulics, and electrical components Wheelhead Disassembly, cleaning of parts, replacement of worn and defective components, motor overhaul, replacement of bearings, replacement of belts, spindle disassembly, replacement of seals and O-rings, plus adjustment. New paintwork. Workhead Disassembly, cleaning of parts, replacement of worn and defective components, motor replacement, replacement of belts. New spindle bearings. New paintwork. Tailstock Disassembly, cleaning of parts, replacement of worn and defective components, motor replacement, replacement of belts. New spindle bearings. New paintwork. Internal grinding attachment Disassembly, cleaning of parts, replacement of worn and defective components, installation of the support and geometry alignment. New paintwork. Hydraulics Disassembly, motor replacement, hose replacement, defective and worn parts replaced. Hydraulic block checked. X-Axis Disassembly, replacement of worn items such as O-rings, seals, rings, etc., overhaul of hydraulic piston, regrinding of tables. Z-Axis Disassembly, regrinding of tables, replacement of worn and defective parts, overhaul of hydraulic piston, scraping of V and flat guides. New paintwork. Measuring system Digital 2-axis display included. Electrical cabinet Replacement of motor contactors and relay controls. New wiring. New variable speed drive (frequency inverter) for the workhead. TECHNICAL SPECIFICATIONS Distance between centers: 1500 mm Distance between centers (workhead to tailstock overhang): 1650 mm Center height, standard: 125 mm Center height with riser blocks: 225/250 mm Maximum grinding diameter: Ø 250 mm Maximum grinding diameter with riser blocks: 450/500 mm Table Usable surface: 2060 x 140 mm Max. length and width for surface grinding: 1750 x 200 mm Longitudinal travel, manual or hydraulic: 1750 mm Manual table movement, 1 handwheel revolution – coarse: 20.006 mm Manual table movement, 1 handwheel revolution – fine: 2.457 mm Table speed, continuously via hydraulics: up to 6 m/min Table swivelling: 6° Stop and return: 0–5 sec. Workspindle Workpiece speeds, continuously variable (electric): 20–400 rpm Swivelling: 360° Workspindle taper (internal): MT5 Tailstock Internal taper, tailstock spindle: MT3 Spindle retraction, manual or hydraulic: 30 mm Diamond dresser taper (internal): MT0 Universal grinding head Cross slide travel for wheel: 285 mm Rapid traverse for wheel slide, front and rear: 40 mm Grinding spindle speeds: 1500 – 1700 – 2200 – 3600 rpm Vertical grinding spindle movement, center heights: 125–330 mm Max. wheel for cylindrical grinding: 400 x 50 x 127 mm Max. wheel for surface grinding: 250 x 20 x 76 mm Head swivelling with locking at every 90°: 270° Wheel feed 1 division of the micrometer drum: 0.005 mm/Ø Automatic wheel feed, max.: 0.9 mm/Ø Gsdpfxjxt Ilfo Afnstu Motors Grinding spindle motor: 2,900 rpm / 4.0 hp Workspindle motor: 3,000 rpm / 2.0 hp Coolant pump motor: 2,850 rpm / 0.12 hp Internal grinding attachment Bore: 70 mm Internal grinding spindle speed Ø70 mm: 14,000 rpm Internal grinding spindle speed Ø50 mm: 21,000 rpm Subject to error or omission, the technical information is provided without obligation.

Condition: used, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm dimensions of the machine ca. 3,6/3,5 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your is: Kellenberger Kel-Varia Baureihe mit Kelco 90 Steuerung. Mechanische Überholung: -komplette Maschine nach Kellenberger Messprotokoll überholt -Neue servicefreundliche Kabine -Neulackierung Elektrische Überholung: -Neue moderne CNC-RUNDSCHLEIFMASCHINEN-Steuerung -Neu aufgebauter Schaltschrank -Neue Antriebstechnik -Austausch sämtlicher elektrischer Leitungen Berus Druckschalter etc. -Neue Absolut-Glasmaßstäbe in x- und z -Neuer Absolut Drehgeber (Bei-B-Achse) Standardausstattung: -WSS mit Konus MK5, optional mit Adapter MK5/Kurzkegel -RST mit MK4 Konus. Optional mit Feinverstellung -Schleifspindelstock T1/T2/T3 -T1 Schleifscheibendurchmesser 400mm -T2 Schleifscheibendurchmesser 300mm -T3 Innenschleifeinrichtung riemengetrieben. -Schleifspindelmotor 4,4kW -B-Achse hochauflösend Gjdpsuwv H Tsfx Afnjtu -Marposs Messsystem zur Schleifscheibenvermessung. -Längspositionierung Marposs -GAP Control (Sensor am Schleifspindelstock) Optionen gegen Aufpreis: -HF Innenschleifspindel -Hochgenauer, höchst kippsteifer Werkstückspindelstock -Messteuerung Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: excellent (used), We have two identical Steriflow 1371 EL retorts available for sale. 1300mm diameter, 7 trolley capacity, single door. They were bought to produce long life ready meals in plastic ready to eat trays. The two machines remain in lovely condition and can also be sold with 3 x 5 trolley Steriflow units if required. The retorts are currently stored in Finland and viewing can be arranged prior to them coming here to the UK. Gtsdpfx Afow Rn Uponju