Binder MKT 240 E3 Temperature Test Chamber –70°C to +180°C

Binder Umwelt-Simulationsschrank MKTS 240

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: Guodpowzl Hxjfx Aaxeh * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: used, Year of construction: 2010, No. 3214 Feed-through veneer press Sergiani LAS Plus Used, year of construction 2010, already dismantled and stored Automatic press with continuous operation for the production of barrier doors, finished doors (veneer doors, HPL, CPL) and pre-treated parquet (2 - 3 layers). The press can be used to load the workpieces one after the other, while the pressure in the other compartments is kept constant. Up to 2 employees are required to operate the line. The multi-daylight press enables a very high production output. The pressing time is approx. 3 minutes (180 seconds) and is spread over 10 levels, which means that the press opens every 18 seconds and a new panel is processed. The press has already been dismantled and stored. The system was in operation until it was dismantled. The previous owner produced 3-layer parquet with the system. The bottom layer was inserted manually. The middle layer consists of one piece. This was glued at the top and bottom and automatically inserted into the system. The top layer was also inserted automatically. Glue spreader / glue applicator not included (optionally available) Stages: 10 Pressing force: approx. 5.5 kg/cm² Total force: 200 tons Gsdov Sthgopfx Aaxjuh Panel size: approx. 2500 x 1300 mm LW Heating: Hot water Area of application: Production of doors, laminating, veneer and wood-based material processing High productivity with a capacity of up to 1200 doors per shift (factory specification) Vacuum loading system with 2-lane infeed roller conveyor, without gluing Scissor lift table with loading belt (belt approx. 2900 x 1000 mm LW) Vacuum stacking station with outfeed roller conveyor Space requirement for press with loading table approx. 6500 x 2365 mm LW Space requirement for entire production line approx. 25000 x 5710 mm LW Sale on behalf of customer, ex location near 5020 Salzburg (Austria), without transportation and assembly Loading and transportation by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: reconditioned (used), functionality: fully functional, Veneering press line for wood, consisting of the following machines: - OSAMA S2R adhesive applicator - 1300 mm - NEW MACHINE - Feeder from the adhesive applicator to the conveyor - Infeed conveyor, 6000 mm long x 950 mm wide, with drive Guodpfx Aevva Syoaxjh - ORMA 5100x1400 mm surface hydraulic press - 12 pistons, hot water plates, refurbished - Outfeed conveyor, 6000 mm long x 950 mm wide, with drive This press requires medium to high pressure for operation to ensure that the boards are 100% flat. Dimensions of veneering boards: 5100 x 1400 mm (solid, drilled steel boards) Board opening: 180 mm Pressure at full surface: up to 10 kg/cm2 Number of hydraulic pistons: 12 pcs - piston diameter 140 mm Teflon MYLAR film on the boards Preparation for heating the boards with hot water - without a boiler Machine dimensions: 2300 x 5100 mm x height 2500 mm The machine has been completely refurbished, adjusted, and tested. Price: EUR 49,000,- excluding VAT, without the OSAMA adhesive applicator Price: EUR 58,000,- excluding VAT, including the OSAMA adhesive applicator