Screw Compressor ZT22

Atlas Copco ZT22

Condition: new, functionality: fully functional, machine/vehicle number: 8153336470, overall weight: 616 kg, volume flow: 399 m³/h, pressure (min.): 4 bar, pressure (max.): 13 bar, noise level: 67 dB, type of cooling: air, Equipment: documentation/manual, refrigerant dryer, type plate available, We are a company specializing in the compressed air industry for over 20 years. Professional level of service and high quality goods offered by our company - "proven" on the market - guarantee successful cooperation with you. We offer NEW screw compressor Atlas Copco GA37VSDs FF (variable speed with built-in dryer) Machine equipped with frequency converter (inverter), manufactured based on the latest technologies, which translates into greater efficiency and performance: On average 20% lower unit energy consumption (SER) than in previous models of the GA VSD series. Ecological and efficient VSD+ variable speed drive system reduces energy consumption by an average of 50% compared to models that operate at idle speed. Regardless of energy savings, efficiency (FAD) increases by up to 12%. Efficient fan motor (compliant with the ERP 2015 directive) reduces energy consumption and noise level. Superior Motor Efficiency (iPM) up to 94.5% exceeding IE3 efficiency levels. Built to work hard for your success. The industry-leading GA Series oil-injected rotary screw compressor delivers unmatched efficiency, high productivity and low cost of ownership – even in the harshest conditions. Technical data: capacity at 4 bar: 15.69- 13.75 l/s / 0.94-7.85 m3/min capacity at 7 bar: 15.67-129.35 l/s / 0.94-7.76 m3/min capacity at 10 bar: 15.68-110.79 l/s / 0.94-6.65 m3/min Max pressure 10 bar (13 Bar variant on request) Voltage 400 V Motor 37 kW Noise 67 dB(A) Weight 616 kg Cjdpjwlp Hdsfx Ap Dehd Motor with internal permanent magnets (IPM) Compression element Direct drive Innovative fan Separator/oil filter with durable construction Electronic water drain valve that does not cause compressed air losses Controller Elektronikon Inlet valve VSDs module Manufacturer code: 8153336470 If you are not sure whether the device is right for you, you have not found the right compressor, CALL! We will advise you on the right choice of device. We invite you to familiarize yourself with our full offer.

Condition: used, Year of construction: 1994, functionality: fully functional, Item: AS-10177 - Alfa Laval Decanter For sale: Used, 5x Alfa Laval Decanter Centrifuges NX 418 S-31G (Year 1994) with Valve & Piping Units Manufacturer: Alfa Laval Separation A/S (Søborg, Denmark) Alfa Laval Decanter Centrifuge – Type NX 418S-31HS High-quality Alfa Laval decanter centrifuge, manufactured in Denmark. Complete unit with Flender / ATB Loher 37 kW main drive motor, electrical control cabinet, stainless steel frame, and integrated piping system. The unit is in very clean condition and was previously used in food processing. Technical details: Manufacturer: Alfa Laval Separation A/S, Denmark Type: NX 418S-31HS Material: Stainless steel Main motor: Flender / ATB Loher 37 kW, 1470 rpm, 380 V, IP55 Drive type: Belt-driven main motor Mounting: Stainless steel base frame Control system: Electrical panels and valve system included Condition: Used, in very good working condition Performance / Capacity: Dairy / whey / milk solids: 5,000 – 10,000 L/h Food / beverage (juice, yeast, starch): 6,000 – 12,000 L/h Industrial / sludge applications: 3 – 8 m³/h (depending on solids content) Bowl diameter: 418 mm Bowl speed: up to approx. 4,000 rpm Max G-force: approx. 4,000 × g Chjdjxqga Ajpfx Ap Ded Applications: Ideal for dairy, food, beverage, starch, chemical, and industrial wastewater separation processes. Location: Denmark Price: On request Package Options: Available as a complete line (3 x decanters + 3 x valve sections) Or sold individually with matching valve section Location: Stored in Denmark, ready for loading. Export documentation and transport arrangements can be provided.

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, 1. Waterjet cutting system with accessories, year of manufacture 2005, machine number: 95 246, Model 4060D, including: 2. Machine details: - NC 4060 D (Duplex with 6 cutting heads for abrasive cutting) - 1 x cutting table: 4200 x 6700 mm - X-axis travel: 2750 mm - Y-axis travel: 6470 mm - Z-axis travel (height): 250 mm - Positioning accuracy (X/Y): +/- 0.075 mm/m - Repeatability (X/Y): +/- 0.05 mm - Feed rate X: 10,000 mm/min - Feed rate Y: 10,000 mm/min - Feed rate Z: 4,000 mm/min Technical specifications: Chsdpfoxgumcex Ap Ded - 1 x Fanuc GE 300 i (NANO CNC) SYSTEM Control functions • 15-inch color LCD display (resolution 1024 x 768) • Machine control panel • 1.5 GHz Pentium III processor • Vertical and horizontal soft key bars • Slim operator panel with QWERTY keyboard • 40 GB program storage (hard disk) • 2 MB RAM for part programs • Windows 2000/XP operating system • Hand-held control unit (remote control) for easy axis positioning – 1 x MPG unit – 6 x WJS standard cutting heads mounted on holders (2 x 3 pieces) – 6 x SM 3000 abrasive metering units – 1 x IGEMS Standard or Professional – 1 x documentation – 2 x abrasive storage tanks, 1,500 l each – 1 x sludge removal system, 3 x diaphragm pumps – 1 x wastewater tank 1,500 l – 1 x cascade tank – 1 x new stainless-steel cutting tank (4 x 6.7 m) - 10 m high-pressure hoses with fittings - 1 x KMT high-pressure pump, 100 HP, 4,100 bar, only 9,500 operating hours - Installation and maintenance by WJS personnel Machine connections: Electrical connection: 3 x 400 V+N+PE, 25 A, 50 Hz Compressed air supply: 600 l/min Air pressure (technically dried): 6.5 bar

Condition: as good as new (ex-display), Year of construction: 2026, machine/vehicle number: MA0139_1335, Exhibit immediately available: New Kaeser Aircenter SK 22 - 8 bar screw compressor with integrated refrigeration dryer and 315 liters compressed air tank Control Sigma Control 2 Year: 2026 Operating hours: 1 hr Pressure: 8 bars Rated power: 11KW Delivery quantity: 2.00 m³/min Sound level: 66 dB(A) Compressed air outlet: 1" Compressed air tank: 350 liters volume Pressure dew point refrigeration dryer: + 3°C Electrically level-controlled condensate drain: ECO DRAIN Dimensions length x width x height: 750 x 1335 x 1880 mm Weight: 579 kg Visit our store. We always have a wide range of new and used compressors in stock! Cjdpehwwyrsfx Ap Dshd

Condition: ready for operation (used), Year of construction: 2008, A screw compressor Atlas Copco with integrated refrigerated dryer including a 500l compressed air receiver is offered. Motor power: 22kW (30hp), Volume flow: 3.84m³/min (64l/s), max. operating pressure: 12.8bar, Operating hours: 29897h, Refrigerant dryer: R134a, 0.95kg. The compressor was serviced annually without interruption by a qualified specialist company. Documentation available. Inspection possible by appointment. Codpfszh Nizsx Ap Djhd

Condition: like new (used), Year of construction: 2019, functionality: fully functional, overall weight: 2,500 kg, temperature: 80 °C, power: 22 kW (29.91 HP), rotational speed (min.): 4,500 rpm, empty load weight: 2,500 kg, screw diameter: 305 mm, year of last overhaul: 2026, Equipment: documentation/manual, rotational speed infinitely variable, Complete Technical Data (GEA OCE 305-01-32)Technical ParameterSpecification and ValuesManufacturer & ModelGEA Westfalia Separator Group GmbH – OCE 305 SeriesEquipment TypeHigh-performance 2-phase decanter centrifuge (Solid-Liquid)Bowl Inner Diameter305 mmBowl DesignFlat-cone design with an extended length (Extended L/D ratio)Maximum Hydraulic CapacityUp to 5 m³/h (varies depending on solid concentration)Maximum Solids Density 2.6 kg/dm³Drive Type2-Gear Drive (System with 2 independent motors, no magnetic brake)Differential Speed ControlAutomatic via dedicated Variable Frequency Drives (VFD)Overall DimensionsLength: 3000 mm | Width: 1000 mm | Height: 1150 mmTotal Weight (Complete Skid)Approx. 2500 kgLubrication SystemAutomatic centralized grease lubrication for main bearingsConstruction MaterialsHigh-grade duplex stainless steel (all product-contact areas)Scroll Wear ProtectionSintered tungsten carbide tiles welded onto the flight edgesII. Liquid Discharge Under Pressure SystemUnlike standard models with gravity discharge (where the liquid falls freely into acollection tank), your model retains the clarified liquid phase inside a hydro-hermetic tripetal Pump (Paring Disk): The separated liquid flows toward the cylindrical end of the bowl, entering a special chamber where a stationary disk with spiral internal channels (a reverse turbine) is etic-to-Pressure Energy Conversion: The kinetic energy of the rapidly rotating liquid is instantly transformed into hydrostatic pressure when it hits the channels of the stationary cess Advantages: The liquid leaves the decanter directly under pressure (without requiring an external transfer pump). This prevents product foaming (highly critical for oils, chemical products, or food-grade applications) and eliminates contact with atmospheric oxygen Electrical cabinet with frequency inverters ant PLC (Siemens ) with acces code for modify the parameters , including factory documentation Cedpfx Ajzgq Szop Dshd

Condition: ready for operation (used), Separator mounted on a stainless steel frame, with feed pump, discharge pump, sludge pump, circulation tank, stainless steel pipes and valve, wired with control box. For the purification of contaminated water. Large water phase, small light phase and dirt phase. No emptying machine !!! Must be opened for cleaning. Time: approx. 5 min. Ready for immediate use. Chsdpfeqzxzgjx Ap Ded We are happy to answer further questions by e-mail!

Condition: excellent (used), PIERALISI Centrifugal Decanter – Stainless Steel PIERALISI industrial centrifugal decanter, designed for the continuous solid-liquid separation of products and suspensions using centrifugal force in industrial processes within the food industry. The equipment uses a high-speed horizontal drum with an internal screw conveyor, allowing for the continuous separation of phases with different densities. The solids are transported to the discharge area while the separated liquid phase is continuously evacuated. Chodpfxjzxcbfj Ap Dsd Its industrial construction in stainless steel, continuous operation, and compact design make this decanter a particularly interesting solution for processes that require clarification, separation, concentration, or solid recovery. MAIN FEATURES -Manufacturer: PIERALISI -Type: Horizontal centrifugal decanter -Application: Solid-liquid separation -Separation process using centrifugal force -Rotating horizontal drum -Internal screw conveyor for solid transport -Continuous separation and discharge -Continuous industrial operation -Construction primarily in stainless steel -Motorized drive -Protected work areas -Robust design for industrial use -Integrable into existing processing lines -Suitable for clarification and concentration processes PROCESS The PIERALISI decanter is designed to continuously separate components of different densities present in a pumpable product. The product enters the rotating drum, where the high centrifugal force causes the phases to separate. The denser solid components move towards the drum wall and are transported by the screw conveyor to the discharge, while the separated liquid phase is continuously evacuated. This principle allows for the following operations: Solid-liquid separation Clarification Solid concentration Dehydration Product recovery Separation of pulps and suspensions APPLICATIONS Especially suitable for food industries, fruit and vegetable processors, oils, juices, and other liquid products with suspended solids, depending on the equipment configuration. PIERALISI centrifugal decanters can be integrated with feed pumps, tanks, filtration systems, clarification systems, and other separation or processing stages. Its continuous operation allows it to be incorporated as either a stand-alone unit or within a complete industrial line. Machine available for inspection. Additional technical information, dimensions, additional photographs, or videos can be provided upon request.

Condition: used, Year of construction: 2016, operating hours: 20,256 h, machine/vehicle number: API831057, Lg.No. 25372 Technical Data: - Operating hours: 20,256 h - Operating pressure: 13 bar - Delivery rate: 4.09 m³/min - Drive: 400 V / 26 kW - Motor speed: 3,000 rpm Csdpfx Apeycvtwj Dehd - Required space approx.: W 900 x H 1,750 x D 900 mm - Weight approx.: 490 kg

Condition: excellent (used), Year of construction: 2006, laser power: 6,000 W, Used Low Cutting Hours Trumpf Trumatic L3050 6kw cnc laser cutting machine for sale Technical information: Year 2006 Workpiece dimensions 3000 x 1500 mm / 3metre x 1.5metre Csdpjrvhzmofx Ap Dehd Type of Laser TLF 6000 Power 6000 Watt / 6kw Control Siemens Sinumerik 840D Longitudinal travel X-axis 3000 mm Cross travel Y-axis 1500 mm Height travel Z-axis 115 mm Travel speed 200 m/min Max cutting thickness in steel 25 mm Weight 12 ton Delivery and installation complete with tuition can be arranged.