Used Bottling Lines UBL S.r.l.

Condition: used, Used bottling line Cortellazzi for CSD in PET bottles – 8000 bph General overview of the line The used Cortellazzi bottling line for carbonated soft drinks in PET bottles 8000 bph delivers an integrated solution for producing soft drinks and sparkling water in 0.50 L and 1.5 L containers. Specifically designed for industrial environments, the system provides a complete technical configuration. It maximizes production efficiency and ensures operational safety by including protection devices and quality control systems at every stage. Moreover, the layout supports continuous operation with minimal downtime. Filling unit and blow molders The Cortellazzi Fintec VEGA 40.70.10 isobaric filling monoblock 1998 handles carbonated products while maintaining constant pressure during the filling process. As a result, the system preserves CO2 content and prevents product loss. Two separate blow molding machines feed the containers. A Sidel SBO8 from 1999 ensures continuous high efficiency production, while a Kosme KSB-4000 from 1998 serves as a backup or support unit. In addition, both machines allow quick format changes and stable operation under load. Carbonator and CO2 management The Cortellazzi Kristal Mix 1998 controls carbonation and saturates the product with CO2. Consequently, the unit ensures consistency and stability throughout the filling phase. Notably, it also supports fine tuning of pressure and temperature parameters. Labeling and customization Three labeling systems carry out specific functions. The Kosme Ekstrahotmelt 12TS1E1 1998 applies labels using hot melt glue. Meanwhile, the KHS Carmichael 1995 handles traditional label application. Furthermore, the Esleeve ESM 3200M 2004 applies shrink sleeves to PET containers in various formats. Together, these machines offer flexible labeling solutions for different product lines. Quality control and heat tunnel The Krones Miho module 2008 inspects containers and labels, detecting any defects or irregularities. If necessary, the system can reject non compliant items without interrupting the production flow. Then, the Krones Shrinkmatt 3000 tunnel 2008 uses steam to shrink the sleeves uniformly onto the containers. In particular, this tunnel guarantees even heat distribution, preventing sleeve distortion. Secondary packaging The Dimac Bluestar F30 2007 wraps products into shrink film with speed and precision. As such, this unit optimizes grouping and prepares the packs for palletizing. Additionally, it minimizes material waste and ensures a clean wrap. Handle and cap application The Twin Pack MGE 1997 applies handles to the grouped bottles. Simultaneously, the Bortolin Kemo 1997 feeds caps consistently and ensures uninterrupted sealing of containers. This way, the two systems maintain rhythm and alignment on the line. Kslhccswukuzeqrslu End of line and automation The Keber Meg Arm palletizer 1998 arranges the finished packs onto pallets.

Condition: used, Used bottling line SMI for CSD 14000 bph: technical specifications SMI built the Used bottling line SMI for CSD 14000 bph in 2010 and configured it for bottling carbonated soft drinks and sparkling water in PET containers. Consequently, the line reaches a production speed of 14,000 bottles per hour and processes 0.50 L, 1.0 L, and 1.5 L formats with high efficiency. Moreover, the layout allows for seamless integration of all subcomponents. Containers and packaging The system handles PET bottles with a 28 ALASKA 267 neck and uses plastic screw caps for sealing. It applies adhesive labels, while packaging is done using shrink film only. In particular, the line supports 3×2 and 4×3 bundling patterns depending on the container size. It also applies adhesive-tape handles to each bundle, ensuring ergonomic handling. As a result, the packaging meets both logistical and retail requirements. The palletizing system uses wooden pallets measuring 800×1200 mm, which conform to standard European formats. Main components of the bottling line Kljlhowt Urbjccqrju The Used bottling line SMI for CSD 14000 bph includes an Ecobloc 8-66-8 block by SMI, which integrates stretch-blow molding, filling, and capping into one compact structure. Therefore, it reduces both footprint and maintenance complexity. A Smiform chiller, also by SMI, provides reliable cooling throughout the bottling cycle. Furthermore, the Chemicount Lubry-Sec unit doses lubricants precisely into the system. As such, it ensures smooth container flow along the conveyors. A P.E. Labellers machine applies the adhesive labels with accurate alignment. Additionally, a VIDEOJET printer prints batch codes, expiration dates, and other data directly onto the bottles. Conveying and end-of-line equipment SMI’s Smiline conveyors transport bottles throughout the entire line with high reliability. At this stage, the Smiflexi handle applicator places adhesive handles on multipacks efficiently and with minimal downtime. Next, the SK 450 F shrink wrapper, also by SMI, bundles the bottles using shrink film, adapting to different formats automatically. Following this, the Smipal palletizer stacks the finished packs onto pallets in optimized layouts. Finally, the Biesse Orbiter pallet wrapper secures the load with stretch film, preparing it for transport. Environmental and operational conditions The Used bottling line SMI for CSD 14000 bph operates in ambient temperatures between -5°C and +35°C. In indoor conditions, it performs best between +20°C and +30°C. It functions reliably at altitudes up to 500 meters above sea level, making it suitable for many production facilities. Humidity up to 60 percent does not impair functionality; however, maintaining proper ventilation is advisable. The system requires a 400 V power supply with a frequency of 50 Hz and tolerates voltage variations of ±10 percent. Operators must supply blowing air at 40 bar and service air between 4 and 10 bar, depending on the machine.

Condition: used, Used bottling line SIDEL for still water in PET bottles 25200 bph The used bottling line SIDEL for still water in PET bottles 25200 bph provides a complete solution for bottling still water. Currently, the line remains connected to power, so buyers can test it directly. SIDEL designed the system in 2006 to handle PET bottles ranging from 350 ml to 1.5 liters. As a result, the line maintains high productivity and flexibility. General line data Kelhccqewr T E Rsrjlu This used bottling line SIDEL for still water in PET bottles 25200 bph processes up to 25200 bottles per hour. Specifically, it uses 30/25 neck-type bottles, which match standard formats across the industry. SIDEL equipped the line with a SB014 blow molder featuring 14 cavities. Furthermore, the filling and capping monoblock includes 40 filling valves and 10 capping heads, making it suitable for still products. Main installed machines The line includes, among other components, an AF high-pressure compressor (model CE46A) and a Fusheng low-pressure compressor (model SA110A). In addition, a BAC cooling tower manages process temperatures effectively. The SIDEL SB014 blow molder, which includes a hopper, feeder, and dust remover, connects directly to the SIDEL SFGL40/10 filling machine. Consequently, the line maintains efficiency across all stages. Labeling and packaging SIDEL integrated a Rollquattro labeler that applies roll-fed wraparound labels with precision. Moreover, a shrink-wrapper creates stable multi-pack bundles using plastic film. The VANTA WSD-B350 carton packer, built in 2011, handles up to 35 cartons per minute. Likewise, a palletizer automates the end-of-line phase, thereby preparing products for shipment. Conveying system and internal logistics The conveying system uses SIDEL-built conveyors throughout the process. Accordingly, the line ensures uninterrupted flow from the blow molder to the palletizer. Thanks to this automation, the system reduces manual intervention and improves consistency. In contrast to fragmented setups, this configuration enhances operational control and reduces downtime. Operating conditions and advantages This used bottling line SIDEL for still water in PET bottles 25200 bph operates under power and remains available for on-site testing. In practice, the integration of SIDEL machines improves performance while simplifying maintenance. As such, operators can rely on uniform quality and long-term reliability. Applications and compatibility The line suits facilities bottling still water in PET containers of multiple sizes. Importantly, its modular design enables quick format changes with minimal disruption. Because of this, companies can adapt to different production requirements. Notably, the system supports both small batches and high-volume output. Technical conclusion The used bottling line SIDEL for still water in PET bottles 25200 bph delivers a robust, efficient, and scalable bottling solution. Undoubtedly, SIDEL’s engineering ensures durability and optimal integration. For this reason, companies seeking a cost-effective way to expand production will find this line technically sound. Ultimately, it represents a valuable opportunity for those who need to scale operations without investing in new machinery.

Condition: used, Used filling line for water for PET containers 5L 800bph This used filling line for water for PET containers 5L 800bph provides a complete solution for processing 5-liter PET bottles, both round and square. Specijalka from Serbia manufactured the line in 2006. Although the owner disconnected it eight years ago, they confirm that it remains in proper condition. Furthermore, you can inspect the line in dry cycle mode. Technical specifications of the filling line The used filling line for water for PET containers 5L 800bph reaches a nominal output of 800 bottles per hour with 5.0-liter containers. Specifically, the system includes a 10-valve rinser, an 8-valve filler, and a 4-head capper, all integrated in a monoblock. Additionally, a cold-glue labeler applies paper labels. As a result, the setup handles rinsing, filling, capping, and labeling in a compact layout. PET bottle production unit In addition to the filling line, this offer includes a semi-automatic PET bottle blower built in 2004. The machine uses two-cavity molds and can produce 800 bottles per hour at 0.5 liters, 600 bottles per hour at 1.5 liters, and 400 bottles per hour at 5 liters. Notably, the system uses water cooling to maintain operational price includes molds for 0.5-liter round bottles and 5-liter square bottles. Consequently, this unit complements the filling line perfectly and allows in-house preform blowing. Kolhowr T E Dsccqrslu High-performance compressor for blowing To support the above components, a BOGE compressor from Germany (2006) is also available. It delivers 11 kilowatts of power, 35 bar of pressure, and a flow rate of 1290 liters per minute. Moreover, the system includes a 1000-liter air tank rated for 40 bar. The unit has only logged 500 operating hours. Thus, it remains in excellent mechanical condition. Importantly, this component ensures adequate air supply for blowing PET bottles reliably and efficiently. Technical conclusion In summary, this used filling line for water for PET containers 5L 800bph enables small to medium-sized producers to manage the complete bottling process autonomously. Specifically, the line handles rinsing, filling, capping, and labeling. Meanwhile, the included blower and compressor provide the necessary infrastructure to blow bottles from preforms. Therefore, producers can oversee every phase of water bottling from bottle production to final packaging.  

Condition: used, operating hours: 30,000 h, Used CFT can filling line for soft drinks – 12,000 cans per hour Introduction and Production Capacity The Used CFT can filling line for soft drinks – 12,000 cans per hour delivers a complete solution for filling carbonated beverages in aluminum cans. CFT designed the line in 2017 and configured it to handle two Slim formats, which are commonly used in the soft drink industry. Specifically, the system processes up to 12,000 cans per hour, meeting the output requirements of medium-scale industrial facilities. As of 30/06/2025, the owner will release the line for sale. Therefore, this represents a valuable opportunity for facilities seeking to expand their production capacity. Depalletizing and Initial Inspection Initially, the CFT depalletizer automatically separates empty cans and feeds them into the production flow. Then, a HEUFT inspection unit checks each container for visual defects and dimensional non-conformities. As a result, the system ensures that only clean, undamaged cans move forward for rinsing. In addition, this early inspection step reduces the risk of line stoppages later in the process. Can Conveyance and Rinsing Next, CFT cable conveyors transport the accepted cans to a dual-channel rinser. The CFT rinser cleans the interior of each can using pressurized water jets or sterile air. Consequently, the machine maintains hygiene standards in line with food and beverage regulations. Moreover, the dual-channel configuration improves throughput while reducing contamination risks. Notably, this section plays a key role in maintaining microbiological safety. Filling After rinsing, a CFT monoblock handles the filling and seaming stages with 12 filling valves and 4 seaming heads. The machine processes cans of 150 ml and 330 ml efficiently. It also controls pressure and temperature precisely to prevent CO₂ loss during the filling of carbonated soft drinks. Furthermore, this phase supports both performance and product integrity. In effect, it ensures consistent quality in high-speed conditions. Full Can Inspection and Rejection Following the filling stage, another HEUFT unit inspects the filled cans to verify fill levels, seal integrity, and the absence of leaks. When it detects non-compliant cans, an automated HEUFT rejection module removes them from the line. As such, this step protects the quality of downstream operations. Additionally, it avoids the unnecessary packaging of defective units. Overall, the system minimizes waste and downtime. Conveyance and Packaging Subsequently, CFT conveyors move the approved cans to an SMI shrink wrap packer. The packer forms bundles in several formats: 4×3 (12 cans), 6×4 (24 cans), and 2x2x3 (12 cans). In this way, the flexible configuration supports various packaging and distribution strategies. Besides improving logistics, this packaging versatility allows rapid changeovers between product sizes. Kjljwr T Ewehccqrslu

Condition: used, Year of construction: 2000, Used Wrap Around OCME ALTAIR N/50 3300 boxes/hour Technical Description of the Used Wrap Around OCME ALTAIR N/50 The Used Wrap Around OCME ALTAIR N/50 3300 boxes/hour handles PET and glass containers using high-efficiency wrap-around carton packaging. OCME manufactured this ALTAIR N/50 model in 2000 to support high-capacity bottling lines. As a result, the machine provides a robust and reliable solution for secondary packaging operations. Currently, the machine remains in storage; however, the team has preserved it under controlled conditions to ensure its operational integrity. Furthermore, its compact and modular structure allows manufacturers to install it in both existing and new production layouts. Configuration and Operation The Used Wrap Around OCME ALTAIR N/50 3300 boxes/hour uses a straight-line infeed, which consistently guides containers into the carton-forming area. Once bottles enter, the machine folds the carton blank around them and seals it during the same cycle. In particular, its mechanical synchronisation allows the forming, folding, and gluing phases to occur smoothly and efficiently. As a result, the unit maintains high packaging precision. Moreover, technicians can perform format changes quickly, thereby reducing downtime. In addition, the simplified layout improves accessibility for maintenance and adjustment. Because of this, operators can optimize changeovers with minimal training. This machine handles bottle formats of 0.75 L and supports the following carton configurations: 3×2, 3×4, and 3×6. This versatility makes it suitable for various production needs and packaging formats. Performance and Output Capacity The Used Wrap Around OCME ALTAIR N/50 3300 boxes/hour processes up to 3300 cartons per hour, regardless of whether it uses the 3×2 or 3×4 format. In the 3×2 configuration, the machine packages 19,800 bottles per hour. In contrast, the 3×4 configuration handles 39,600 bottles per hour, since each carton contains 12 bottles. Thanks to this flexibility, operators can respond quickly to shifts in production demand. In fact, the mechanical setup supports high-speed operation even under heavy workload. Consequently, the machine guarantees steady performance across a wide range of applications. Furthermore, engineers can rely on its repeatability to maintain strict packaging standards. Safety and Compatibility Kolhccqewrpnberolu OCME equipped the Used Wrap Around OCME ALTAIR N/50 with integrated safety systems. These include photoelectric barriers, emergency stop buttons, and protective guards in every hazardous area. Therefore, the system complies fully with European safety standards. Moreover, it ensures a safe working environment without compromising productivity. The machine works seamlessly with both PET and glass containers. This compatibility enables production teams to use it across diverse product lines. In addition, it accommodates format switching without recalibrating the entire system.

Condition: used, operating hours: 4,000 h, Used Line for olive oil production PIERALISI 700 kg/h Overview of the Line The Used Line for olive oil production PIERALISI 700 kg/h offers a complete and professional solution for the transformation of olives into extra virgin olive oil. Manufactured in 2014, this processing line includes exclusively PIERALISI machines, a benchmark brand in the olive oil sector. With a rated capacity of 700 kg/h, the system suits medium-sized producers who require durability, consistent performance, and high processing quality. Consequently, it provides an ideal balance between efficiency and compact footprint. Furthermore, it adapts well to various operational contexts. Machine Condition and Materials The seller has completely overhauled and repainted all machines in the line. As a result, the system is in excellent working condition. It includes full electrical and mechanical safety protections, which ensures compliance with modern standards. The manual control panel operates in perfect condition and comes with updated PDF wiring diagrams. In addition, all surfaces that come into contact with the product are made of AISI 304 stainless steel, which guarantees food-grade quality and long-term resistance to corrosion. Thus, the line ensures hygienic and durable operation. Initial Processing Phase The process begins with a receiving tank PIERALISI EFFE 3, where the olives enter the line. Immediately after, a feeding pump PIERALISI 2 Cv transfers the product from the tank to the crusher. This pump, which has a new stator, operates in like-new condition and is paired with a 140-liter stainless steel tank. Moreover, the pump design supports stable and continuous flow. It feeds the olives into the crusher PIERALISI EFFE 3, which features a twin-screw system with cycloidal gears. Therefore, it ensures efficient and uniform paste production. In this way, it prepares the raw material for malaxing. Klelhcjwqxhuscqrju Malaxing and Pasta Handling After crushing, the olive paste proceeds to the malaxer PIERALISI with a 2-ton capacity. If required, the operator can divide the malaxer into two separate vessels, each with an independent outlet. This option allows more control over the feeding process to the decanter. Additionally, it improves flexibility in handling various olive batches. For this reason, the malaxing stage becomes highly adaptable. Meanwhile, it maintains optimal mixing conditions for oil extraction. As such, the line supports both continuous and batch workflows. Separation and Oil Extraction The PIERALISI EFFE 3 decanter centrifuge forms the core of the Used Line for olive oil production PIERALISI 700 kg/h. This unit automatically separates the solid pomace from the liquid phase and supports a capacity of 700 kg/h. Importantly, it operates in both two-phase and three-phase modes, depending on the processing goals. Subsequently, the separator PIERALISI P1500/2000 (10 Hp) performs the final clarification step.

Condition: used, Used UHT Milk Preparation Room Tetra Pak 6600 L/h Technical Overview of the System The Used UHT Milk Preparation Room Tetra Pak 6600 L/h provides a complete solution for the aseptic preparation of UHT milk, drinking yoghurt, juices, and flavored beverages. Currently in storage and ready for reinstallation, the system delivers high thermal and microbiological efficiency. Moreover, its modular design allows it to operate at 2640 L/h, 3850 L/h, and up to 6600 L/h in full configuration. Therefore, it adapts well to varying production demands. Homogenization Section At the core of the Used UHT Milk Preparation Room Tetra Pak 6600 L/h lies a Tetra Pak homogenizer, model Tetra Alex, which ensures effective fat globule size reduction and consistent product texture. As a result, it stabilizes complex emulsions such as flavored milk or drinking yoghurt and prevents phase separation during storage. Importantly, this homogenizer is non-aseptic and operates upstream of the UHT sterilization process, which eliminates any microbial load introduced during homogenization. Furthermore, the homogenizer supports high working pressures and simplifies maintenance. In addition, the robust construction ensures long-term reliability. Integrated Deaeration System The system includes a Tetra Pak deaerator (2005) equipped with an auxiliary pump and tank. Specifically, this component removes dissolved oxygen and unwanted gases from the product before thermal processing. Consequently, it improves product stability and reduces oxidation. Additionally, the vertical configuration ensures efficient gas separation. Meanwhile, the design minimizes product loss and guarantees a continuous flow to the next stage. High-Performance Tubular UHT Module Thermal sterilization occurs through a tubular UHT heat exchanger, manufactured by Tetra Pak and model Tetra Therm Aseptic. In particular, this component sterilizes products via indirect heat exchange while preserving organoleptic properties. Importantly, the module includes a holding coil to maintain temperature over a defined time span. Thus, it complies with food safety regulations and ensures microbiological safety. Similarly, its modular design allows for easy integration into existing lines. Klolhccowqxhhsqrsu Electronic Control and Automation The line features an electrical control panel, a Siemens PLC, and operator panels for precise management of each phase. Notably, it includes detailed electrical schematics, Festo pneumatic valves, and Danfoss inverters to dynamically control pumps and heat exchangers. As such, the automation enables continuous processing. Besides, it optimizes the CIP cycles, reduces downtime, and enhances traceability. Above all, it ensures reliable performance across diverse operating conditions. Conclusion In summary, the Used UHT Milk Preparation Room Tetra Pak 6600 L/h offers a complete, high-efficiency system for preparing UHT milk and beverages. Thanks to its top-tier components and scalable design, this line stands as an ideal choice for dairy producers. Whether the goal is reliability, hygiene, or adaptability, this solution meets strict industry standards. Finally, the system remains in storage and is available for immediate installation.

Condition: used, Year of construction: 2005, Used labeling machine PE Master M for adhesive labels 6000 bph Technical overview of the model PE Labelers built the used labeling machine PE Master M for adhesive labels 6000 bph in 2005 to serve medium-capacity bottling lines. Specifically, the machine handles 0.75-liter bottles and processes up to 6000 bottles per hour. As a result, it provides an optimal solution for operations requiring consistent output. Mechanical configuration and operation The manufacturer equipped the PE Master M with six rotating plates that move bottles along a clockwise carousel. Additionally, three labeling stations apply adhesive labels precisely to the front, back, and neck of each container, thereby ensuring full coverage of all critical areas. In comparison to older models, this configuration offers improved label positioning. Self-adhesive labeling method The used labeling machine PE Master M for adhesive labels 6000 bph uses a self-adhesive system to apply labels quickly and with high precision. Notably, the system handles pre-printed labels that adhere immediately, thus eliminating the need for glue. Consequently, it reduces maintenance requirements. Furthermore, the adhesive technology enhances line cleanliness and operator efficiency. Centering system and manual adjustments A mechanical centering system aligns each bottle correctly throughout the labeling process. Therefore, the machine maintains consistency even at high speeds. Operators adjust the label heads manually, which in turn enables fast format changes and precise corrections. Moreover, this setup supports production flexibility. Integrated safety measures The machine includes built-in safety guards that comply with CE regulations. For this reason, it protects operators during cleaning, maintenance, and changeovers. As expected, such safety features align with modern industrial standards. In addition, the layout facilitates quick access to internal components. Energy consumption and system compatibility The used labeling machine PE Master M for adhesive labels 6000 bph draws 3 kW of power and runs on 400 Volt, 50 Hz electrical systems. Consequently, technicians can easily integrate it into standard European production lines. Despite its age, the machine remains compatible with most existing plant infrastructure. Kjlhccswqxhbsqrslu Weight and structural durability PE Labelers engineered this model with a solid 1500 kg structure, which ensures high stability during operation. Above all, the steel frame resists corrosion and withstands demanding industrial environments. In fact, the robust build minimizes vibrations and prolongs service life. In contrast to lightweight models, this unit prioritizes mechanical resilience. Operational performance and reliability The used labeling machine PE Master M for adhesive labels 6000 bph currently runs in working condition, allowing prospective buyers to verify its performance firsthand. Accordingly, it demonstrates the reliability of PE Labelers’ design. Overall, the machine combines mechanical precision, ease of use, and long-term stability. Therefore, it serves as an excellent solution for bottling plants that prioritize quality, uptime, and simple maintenance routines.

Condition: used, Year of construction: 2018, Used Filling Monoblock for beer 800 bph Monoblock Structure The Used Filling Monoblock for beer 800 bph consists of three separate units: an automatic rinser, an isobaric filler with a double vacuum system, and a crown capper. This configuration optimizes the management of rinsing, filling, and sealing phases. As a result, the system ensures suitability for processing beer in 0.5-liter glass bottles. Moreover, this modular layout facilitates maintenance and replacement, therefore increasing operational reliability. Kelhswqxg Roccqrelu Rotary Rinser ZPC-12 The rinser in the Used Filling Monoblock for beer 800 bph operates with a continuous rotation system and uses 12 gripping clamps. First, the operating cycle handles bottle entry. Then, it performs internal rinsing with treated water, followed by dripping and final exit. The machine handles glass bottles with a height between 150 and 330 mm and a diameter between 50 and 90 mm. It processes 600 to 800 bottles per hour. The installed motor delivers 1.5 kW of power. Additionally, the design allows rapid changeovers between bottle formats, which enhances production flexibility. Isobaric Filling with Double Vacuum The BFP-12 filling unit, at the heart of the Used Filling Monoblock for beer 800 bph, includes 12 filling valves and applies an isobaric process with double vacuum. Specifically, the system performs two evacuation cycles and CO₂ reinjections before the filling stage. Consequently, it significantly reduces residual oxygen and preserves beer quality. It supports bottle volumes from 250 to 1000 ml. Furthermore, the unit integrates key components such as a Southern Pump, a Mitsubishi PLC, a THINEDA touchscreen, Korean-made sensors, and AUTONICS pneumatic systems. This machine also operates with a 1.5 kW motor. In terms of control, the electrical interface provides real-time adjustments, thus improving accuracy during production. Crown Capping Machine ZDS-3 The crown capper of the Used Filling Monoblock for beer 800 bph applies metal crown caps to glass beer bottles. The machine includes 3 capping heads and operates with a continuous rotary motion. It handles bottles up to 330 mm in height and caps with diameters from 20 to 30 mm (cP size), compatible with the normal European neck type. Notably, the capper reaches up to 1500 bottles per hour, thereby providing an operational buffer that prevents bottlenecks downstream of the filler. In comparison to standard cappers, this model delivers greater precision and cap stability. In addition, its robust frame reduces vibration during high-speed operation. Electrical Characteristics and Compatibility The machines in the Used Filling Monoblock for beer 800 bph use reliable and industry-standard electrical components. The full line features an estimated total power consumption of approximately 4.5 kW. From an integration standpoint, this makes the system suitable for facilities with medium energy capacity. The system exclusively handles 0.5-liter glass beer bottles. During operation, it performs filling under controlled pressure to preserve CO₂ levels and ensure the product’s final stability. Overall, the system delivers consistent performance, reduced oxygen pickup, and excellent packaging quality. Lastly, the compact footprint simplifies installation even in limited space environments.

Condition: used, Used Line Pieralisi Jumbo 2 for olive oil production 2000 kg/h General Description of the System The Used Line Pieralisi Jumbo 2 for olive oil production 2000 kg/h provides a complete technical solution for transforming olives into oil. All machines, except for the washing machine and the progressive cavity pump, belong to the Pieralisi Jumbo 2 line, manufactured in 1995. Currently, the entire line remains in storage and includes active and functional safety devices. Therefore, the system is ready for deployment. This setup operates in a fully continuous cycle and delivers a nominal capacity of 2,000 kg/h, ensuring stable productivity throughout each phase. Washing and Transport Section Initially, the Used Line Pieralisi Jumbo 2 for olive oil production 2000 kg/h uses a TYPE B olive washing machine to remove soil, leaves, and impurities through water flow and filter grids. After cleaning, a screw elevator gently transports the olives to the crusher. Consequently, it minimizes mechanical stress and prevents premature crushing. In this phase, precision is essential to protect downstream equipment and ensure consistent paste quality. Moreover, it contributes to the overall efficiency of the process. Crushing and Malaxing Next, the crusher receives the olives and breaks them down using a hammer-based mechanical system. This procedure generates a uniform paste, which then enters the malaxing stage. The line features three malaxers of 900 kg each, which operate continuously. Additionally, they offer temperature and residence time control. As a result, this phase facilitates the coalescence of oil droplets. Furthermore, it significantly improves extraction efficiency in the next step of the Used Line Pieralisi Jumbo 2 for olive oil production 2000 kg/h. Notably, all components maintain temperature integrity throughout the cycle. Transfer and Solid-Liquid Separation Subsequently, a progressive cavity pump, model 60, transfers the paste from the malaxers to the decanter centrifuge. The pump guarantees a steady and non-pulsating flow. In turn, the decanter separates oil, pomace, and vegetation water continuously. With a nominal capacity of 2.5 tons/hour, this decanter exceeds the system’s average flow. Hence, it offers operational flexibility and surplus processing capacity. In addition, the high-capacity design reduces the risk of bottlenecks during peak loads. Clarification and Process Control Kslhewmkqyjccqrolu After separation, the system channels the oil to automatic vertical separators rated at 1,500–2,000 l/h. These units perform final clarification via high-speed centrifugation. At this stage, the control panel actively manages all system parameters, including temperature, timing, and safety states. Simultaneously, a thermal panel assists in maintaining thermal stability across critical points. Therefore, operators can monitor the full cycle with precision. Overall, this integration enhances consistency and simplifies routine supervision.

Condition: used, Year of construction: 2007, Used Robot Palletizer FANUC 10800 bph General Description of the Robot The Used Robot Palletizer FANUC 10800 bph is a high-performance industrial robotic unit specifically designed for automated palletizing operations in bottling plants. The configuration combines the FANUC R-2000iC/165F robot and the R-30iB Plus controller. As a result, the system ensures excellent reliability, mechanical robustness, and positioning accuracy in high-intensity production environments. Operational Capacity and Mechanical Configuration Equipped with a six-axis articulated arm, the Used Robot Palletizer FANUC 10800 bph delivers ±0.05 mm repeatability, in full compliance with ISO 9283 standards. Furthermore, it achieves a maximum reach of 2655 mm and supports payloads of up to 165 kg at the wrist. Thanks to its rotating arm design, the system executes palletizing cycles with high precision. In particular, it grips containers by the neck using pneumatic grippers, thereby minimizing instability and maximizing throughput. The machine reaches a production speed of 10,800 bottles per hour on the 2×6 format, making it ideal for high-efficiency bottling lines. Previous Applications and Current Condition Previously, the Used Robot Palletizer FANUC 10800 bph operated in a water bottling plant, where it consistently palletized 19-liter bottles. Currently, the robot remains in storage, although it is ready for immediate redeployment. Moreover, users can easily reconfigure it for other material handling operations such as transfer, stacking, or sorting. Consequently, it offers high flexibility for integration into diverse industrial settings. Klolswmkqtjhccqrju Control System and Integration The system includes a dedicated FANUC control cabinet, which incorporates all required safety features. Specifically, it offers emergency stops, protective barrier sensors, and remote access interfaces. In addition, the robot features 8 digital inputs and 8 digital outputs mounted on the upper arm, along with 2 integrated pneumatic lines. These components allow for quick connection of peripheral devices, including grippers and detection sensors. Therefore, integration with auxiliary systems is simple and efficient. Power Supply and Operating Conditions In terms of power, the Used Robot Palletizer FANUC 10800 bph operates on three-phase 380–575 V at 50/60 Hz. Its average power consumption remains low at 2.5 kW, which contributes to overall energy efficiency. Furthermore, the unit functions reliably in ambient temperatures from 0 to 45 °C, and it maintains a low acoustic noise level of 70.5 dB. Footprint and Integration Readiness Thanks to its compact 771 x 610 mm footprint, the system easily fits into both existing and newly designed production layouts. Additionally, it communicates with PLCs and SCADA platforms using standard industrial interfaces. As such, it enables synchronized operation with conveyors, vision systems, or labeling modules.

Condition: used, operating hours: 3,900 h, Used bottling truck Kenworth T370 3000 bph Vehicle Configuration and Operating Conditions The Used bottling truck Kenworth T370 3000 bph operates as a mobile bottling unit built on a 2017 Kenworth T370 truck chassis. The vehicle includes an automatic transmission, runs on diesel fuel, and features two front seats in the cab. It currently operates efficiently and shows approximately 95,000 kilometers on the odometer and around 3,900 hours on the onboard generator. As of now, the seller offers the truck for immediate sale and confirms that it does not require any extraordinary maintenance. Furthermore, its overall condition ensures immediate deployment in production environments. Thus, buyers can reduce lead times significantly. Integrated Bottling Equipment Inside the Used bottling truck Kenworth T370 3000 bph, a complete GAI bottling system—manufactured in 2017—manages all key phases of the process. The equipment includes a 12-valve isobaric filler, a 12-spout rinser, and a pressure-sensitive labeler. Additionally, an onboard generator and air compressor power the entire setup. More importantly, the line was specifically designed for bottling carbonated soft drinks (CSD) and beer, maintaining stable pressure conditions throughout the filling process. Consequently, it supports beverage producers with high carbonation standards. In practice, the isobaric filler minimizes foaming and ensures fill-level precision. Meanwhile, the integrated systems operate in sync, maximizing efficiency. Production Speed and Bottle Formats Klolhccqowl I Itsrou The Used bottling truck Kenworth T370 3000 bph currently handles glass bottles in the following sizes: 0.187 L, 0.375 L, 0.50 L, 0.66 L, and 0.75 L. The included format change parts are installed and ready for use. As a result, operators can switch between formats without additional tooling. The system reaches a maximum operating speed of 3,000 bottles per hour while preserving consistency and accuracy across all product types, including beer and CSD. Notably, it uses 26 mm crown caps, which ensure a secure seal even for pressurized beverages. In comparison with other mobile units, this configuration offers greater versatility. Moreover, the setup supports small batches and short runs with minimal reconfiguration. Post-Filling Treatments and Line Flexibility After the filling and labeling stages, the Used bottling truck Kenworth T370 3000 bph uses post-rinser units to remove product or adhesive residue. In certain cases, operators can deactivate the post-rinsing function when using moisture-sensitive paper labels. Therefore, this flexibility allows for broader label material compatibility. From a technical standpoint, the rinsing system enhances product hygiene and packaging quality. In addition, all components maintain modular construction for simplified maintenance and inspection. For instance, switching between post-rinse on/off modes requires minimal manual input.

Condition: used, Used Bottling Lines for edible oil 6000 bph General Configuration of the Bottling Line Kljlhswlt Dgeccqrsu The Used Bottling Lines for edible oil 6000 bph line processes edible oil in 1-liter PET bottles, operating at a nominal speed of 6000 bottles per hour. The configuration includes equipment from multiple manufacturers, integrated to ensure continuous operation and reliability in filling, labeling, packaging, and palletizing. Operators correctly shut down the entire system in December 2022. At present, the machines are dismantled and stored in suitable conditions. Consequently, this line is immediately available for relocation and reuse. Overall, the structure represents a compact yet complete solution for medium-scale production. Container Formation: KOSME Blow Molding Machines The Used Bottling Lines for edible oil 6000 bph line includes two blow molding machines from KOSME, model KSB3000, year 2001. Each unit works with a preform box and an automatic transport system that feeds the blower. As a result, the system supports on-site bottle production. Therefore, it reduces logistics costs and improves plastic material handling. In addition, the dual-machine setup enhances production continuity and minimizes downtime. Cooling System: MTA Chiller and Air Conveyors An MTA chiller, model TAE 051, year 2000, cools the molds in the blow molding machines. Moreover, KOSME air conveyors, model L2000, year 1999, made of AISI 304 stainless steel, transfer the blown bottles to the filling monoblock. Notably, the system includes electrical cabinets with integrated PLCs and built-in air filters. Thus, it ensures effective airflow control and maintains consistent air quality. From a technical standpoint, this contributes to long-term reliability and hygienic conditions. Filling Monoblock: ICS RVP-12/ZS-3N The ICS filling monoblock, model RVP-12/ZS-3N, year 1995, serves as the core of the Used Bottling Lines for edible oil 6000 bph. This machine doses edible oil with precision, ensuring product integrity and consistent fill volumes. Furthermore, the system synchronizes with upstream and downstream units. Consequently, it enables stable operation even under variable load conditions. Likewise, its mechanical construction supports easy maintenance and spare part replacement. Labeling Machine: ICS with Cold Glue An ICS labeling machine, model ERG-6/2/2, year 1995, applies paper labels using cold glue. Specifically, the machine ensures proper adhesion on PET containers. Additionally, it supports the 1-liter format used throughout the line. In practice, this technology remains widely adopted for edible oil packaging. Therefore, the labeling unit integrates efficiently into the overall production layout. To sum up, it provides a cost-effective solution without compromising performance. Internal Handling and Packaging ICS conveyor belts, installed in 1995, connect all key stations. Subsequently, the line transitions to the packaging phase.

Condition: used, Year of construction: 2007, Used Blow Molding Machine SIPA SFR12 18000 bph General Features of the SIPA SFR12 Blow Molding Machine The Used Blow Molding Machine SIPA SFR12 18000 bph performs PET container stretch blow molding and SIPA manufactured it in 2007. As a result of its SFR12 configuration, which includes 12 cavities, the system reaches a nominal speed of 18,000 bottles per hour. Consequently, it delivers high production efficiency across multiple formats. Specifically, this machine processes volumes from 0.25 to 2 liters. Therefore, it fits seamlessly into high-speed bottling lines, particularly in the mineral water and soft drink industries. Moreover, thanks to its compact layout, it optimizes floor space usage. Preform Compatibility and Technical Specifications This machine processes preforms with 3-start Alaska neck finishes and supports weights ranging from 12 to 34 grams. In particular, operators can quickly change formats thanks to the integrated quick-change system, which significantly reduces downtime. In addition, the automated system feeds, tips, and orients the preforms accurately. As a result, the machine ensures a continuous and correctly aligned flow into the heating and blowing stations. Furthermore, this setup minimizes manual intervention and improves process reliability. Notably, the Used Blow Molding Machine SIPA SFR12 18000 bph maintains stable, uninterrupted production across varying operational conditions. Klelhccqowkuyasrou Integrated Systems and Automation The machine uses a Siemens PLC for core process control; thus, it guarantees reliable and intuitive management in industrial environments. Furthermore, the system includes certified safety protections, which enhance operator safety and regulatory compliance. Additionally, the air recovery system reduces energy waste and lowers operational costs. Equally important, the rotary blowing system distributes pressure and heat evenly across all cavities. Hence, the machine ensures uniform container quality even during high-speed operation. In comparison to older models, this version offers improved thermal control and air distribution efficiency. Operational Status and Technical Documentation Currently, the Used Blow Molding Machine SIPA SFR12 18000 bph remains in storage, although it is ready for recommissioning after standard inspection or overhaul. Fortunately, the machine includes original technical manuals, available spare parts, and revision records, which together facilitate seamless installation and integration. Moreover, the documentation enables faster troubleshooting and efficient maintenance scheduling. Technical Summary for Line Integration Overall, the Used Blow Molding Machine SIPA SFR12 18000 bph delivers a robust and high-performance solution for production facilities that require consistent, flexible, and high-throughput blow molding. Because of its solid engineering and standard-format compatibility, it serves as a strategic asset for companies looking to upgrade or expand bottling capacity. Furthermore, the availability of auxiliary components and spare parts, along with comprehensive documentation, allows for rapid and reliable integration. Ultimately, this machine enhances line performance while supporting operational continuity and cost-efficiency.

Condition: used, Used aseptic filling line Tetra Pak A3 FLEX 1000SQ 7000 l/h General description of the line The Used aseptic filling line Tetra Pak A3 FLEX 1000SQ 7000 l/h provides an industrial configuration specifically designed for the sterile filling of liquid food products. It particularly suits sensitive items such as UHT milk and fruit juices, which require controlled processing environments. Moreover, the system operates with 1-liter square containers and reaches a production capacity of 7,000 liters per hour. As a result, it ensures high microbiological quality standards. In this configuration, each machine plays a critical role in maintaining aseptic conditions from filling to final packaging. Aseptic filler Tetra Pak A3 FLEX At the heart of the Used aseptic filling line Tetra Pak A3 FLEX 1000SQ 7000 l/h, the Tetra Pak A3 FLEX filler (version 100V), manufactured in 2004, performs aseptic filling using an integrated sterilization system, microbial barrier, and precise dosing mechanisms. Consequently, it processes pasteurized or sterilized products intended for extended shelf life and keeps them intact without requiring refrigeration. Furthermore, the filler maintains a sterile environment throughout the entire cycle. In addition, it ensures consistent product dosing and eliminates variability in filling performance. As a result, manufacturers can rely on this equipment to meet strict food safety requirements. Aseptic capper Tetra Pak TCA88 Kljlhccqowkux Njrsu The line also includes the Tetra Pak TCA88 capper, built in 2006. This module applies plastic caps to filled containers using induction or mechanical systems that ensure hermetic sealing in an aseptic environment. Moreover, the capper synchronizes precisely with the filler to ensure uninterrupted operation. In contrast to conventional systems, this integration significantly reduces the risk of contamination after filling. In the same way, the TCA88 includes built-in quality control functions that verify each cap’s position and torque. Meanwhile, Tetra Pak designed the unit with safety features such as interlocked guards and error monitoring systems, ensuring full compliance with industry standards. Cardboard packer TCBP70 in this used aseptic filling line Tetra Pak The Tetra Pak TCBP70 packer, manufactured in 2007, manages secondary packaging. This automatic system forms and fills corrugated cartons using wrap-around or preformed box configurations. Similarly, it operates with fully electronic controls that allow real-time adjustment and monitoring. Therefore, the machine supports flexible packaging layouts and rapid format changes. In addition, the TCBP70 includes safety systems such as light curtains and emergency stop devices. For example, if an operator enters the guarded zone, the system halts automatically to prevent accidents. As a result, the packaging process remains both efficient and secure. Industrial applications and operational benefits The Used aseptic filling line Tetra Pak A3 FLEX 1000SQ 7000 l/h targets producers in the dairy and beverage industries who require aseptic packaging capabilities.

Condition: used, Year of construction: 2008, Used Filling Monoblock KRONES Volumetric 36000 bph Overview of the Used Filling Monoblock KRONES Volumetric 36000 bph Kelowixz Sehccqrolu The Used Filling Monoblock KRONES Volumetric 36000 bph integrates a filling and capping unit specifically designed for natural water in PET bottles. KRONES, a well-known German manufacturer, built this machine in 2008. As a result, the unit belongs to the category of volumetric filling systems, which guarantee precision, reliability, and high output. Moreover, it performs efficiently even under demanding production conditions. In terms of capacity, the system reaches up to 36,000 bottles per hour with 0.5 L formats and 25,000 bottles per hour with 1.5 L bottles. Therefore, the machine suits both high-speed lines and flexible production setups. Additionally, it maintains minimal volumetric deviations throughout extended operation cycles. Mechanical Configuration This Used Filling Monoblock KRONES Volumetric 36000 bph features two main modules: a filler equipped with 72 valves and a rotary capper with 18 heads. Notably, the capping system supports plastic screw caps with a 28 mm diameter, designed for PCO 1881 neck finishes. Furthermore, the unit includes two Gassner cap sorters, one for standard caps and one for sport caps. As such, the machine enables fast format changes and accommodates diverse packaging requirements. In addition, the integration of both modules in a single monoblock improves space efficiency and simplifies maintenance procedures. Technicians can easily access all functional areas, which in turn reduces downtime. Volumetric Filling Technology in this Used Filling Monoblock The Used Filling Monoblock KRONES Volumetric 36000 bph uses volumetric filling technology, which ensures accurate dosing regardless of product temperature or density. Specifically, the system relies on flow meters or volume counters to control the filling quantity with exceptional precision. Consequently, this method proves especially effective for water-based products, where loss minimization and product integrity are critical. In contrast to traditional level filling, volumetric systems offer higher efficiency and consistent results. Additionally, the engineers designed the structure to reduce vibrations and maintain optimal stability. As a result, the machine delivers long-term performance and lowers mechanical wear. Moreover, the design allows smooth integration into existing production lines. Condition and Availability of the Used KRONES Filling Monoblock Currently, the Used Filling Monoblock KRONES Volumetric 36000 bph remains dismantled and stored in warehouse, which facilitates immediate inspection or shipping. Importantly, the previous owner performed all maintenance regularly, exclusively using original spare parts. Consequently, the machine retains excellent structural condition and full operational readiness. In addition, it includes integrated safety devices, which comply with industrial safety standards and protect operators during operation and servicing. Unlike machines requiring refurbishment, this unit remains ready for deployment without delay. In conclusion, the Used Filling Monoblock KRONES Volumetric 36000 bph represents a robust and dependable solution for high-output bottling lines requiring precise volumetric control.

Condition: used, Year of construction: 2013, operating hours: 1,700 h, Used Filling Monoblock Alfatek for olive oil 1500 bph General Features of the Used Filling Monoblock Alfatek for Olive Oil 1500 BPH The ALFATEK MBV 9/1 VOLUMETRICA SABRY filling monoblock, built in 2013, offers an efficient and reliable solution for bottling edible oil. It operates at a speed of 1500 bottles per hour, with clockwise rotation and a fully automated workflow. In fact, the machine currently runs in active production, having completed approximately 1700 operating hours. Moreover, it includes all safety protections, user manuals. Container Compatibility and Supported Formats The Used Filling Monoblock Alfatek for Olive Oil 1500 BPH handles a wide variety of containers. Specifically, it works with both PET bottles and metal cans, supporting the following formats: PET 138x138xh253 mm PET 148x148xh320 mm PET 81x81xh236 mm PET 63x63xh184 mm Cans 150x92xh192 mm Cans 150x92xh261 mm Cans 149x120xh315 mm Consequently, the machine adapts easily to diverse packaging needs. Whether the production involves small household bottles or larger industrial formats, this monoblock provides the required flexibility. Additionally, this versatility reduces the need for multiple machines, optimizing both space and investment. Kelhccqowiu Rvorelu Filling Section: Volumetric Technology The filling section of the Used Filling Monoblock Alfatek for Olive Oil 1500 BPH uses 9 volumetric valves. These valves deliver accurate and repeatable dosing, which is especially important for high-viscosity products like olive oil. Notably, the system uses fixed valves and operates in a non-isobaric configuration. Therefore, it suits still liquids and avoids the complexities associated with pressurized systems. Furthermore, the volumetric method helps maintain product integrity while minimizing waste and overfill. Press-On Capping: Compatibility and Sizes The machine applies plastic press-on caps using one capping head, which supports multiple cap dimensions: Ø51.5 x 23 mm Ø37.5 x 22 mm Ø38 x 20 mm Because it handles non-threaded necks, the monoblock accommodates a wide range of container shapes typically used for edible oil. Additionally, the press-on capping system simplifies maintenance and allows for fast format changes. As a result, it ensures both high efficiency and reliable sealing performance. In short, it delivers consistent closure without the need for threading or torque control. Output per Format and Electrical Specifications Depending on the bottle size, the Used Filling Monoblock Alfatek for Olive Oil 1500 BPH achieves varying output rates: 2000 bph for 0.5L and 1L 1500 bph for 2L 1400 bph for 3L 1200 bph for 4L 1000 bph for 5L Thus, the machine performs efficiently across all common olive oil packaging formats. In terms of power, it operates on 415 Volts and 50 Hz, complying with industrial electrical standards. Despite its robust capabilities, the monoblock weighs only 300 kg, making it compact enough for mid-scale facilities. Moreover, its design facilitates both installation and relocation when needed.

Condition: used, Year of construction: 2007, Used Case Sealer APSOL 3500 bph The Used Case Sealer APSOL 3500 bph performs automatic sealing of American-type cartons using hot-melt adhesive. Specifically designed for high-output bottling lines, this automatic case sealer provides reliable solutions that ensure tight closure, consistent efficiency, and enhanced operational safety. With a rated speed of 3500 bottles per hour, it meets industrial demands. Moreover, the machine accommodates multiple container formats and integrates seamlessly with standard configurations in the beverage industry. Technical Specifications of the ACS30HM Model APSOL manufactured this machine in 2007, and it currently operates in production. The structure, although compact, offers robust mechanical performance. Additionally, the integrated DELTA-type PLC system controls the sealing cycle, thermal adhesive regulation, and overall workflow with precision. As a result, operators benefit from accurate process control. The Used Case Sealer APSOL 3500 bph runs on a 400 Volt three-phase power supply, consumes 5 kW, and operates at a frequency of 50 Hz. Therefore, it remains fully compatible with European industrial standards. Supported Formats and Production Flexibility In terms of versatility, the Used Case Sealer APSOL 3500 bph processes various carton formats containing 500 ml, 750 ml, and 1000 ml bottles in 4×3 and 3×2 configurations. Furthermore, it offers high production flexibility and quickly adapts to different layout requirements. Operators can perform format changeovers rapidly; consequently, they minimize downtime and optimize line efficiency. In addition, the design facilitates routine adjustments without requiring extensive reconfiguration. Hot-Melt Adhesive Sealing System Kljlhccqowimngjrju The machine uses a hot-melt adhesive applicator to ensure secure sealing. Unlike mechanical closure systems, this method provides strong adhesion that withstands both mechanical and thermal stress during transport and handling. Notably, the integrated sensors maintain a consistent operating temperature, while the adhesive distribution system guarantees even application. As such, the Used Case Sealer APSOL 3500 bph offers high-quality and repeatable sealing performance. Simultaneously, it reduces the need for rework and rejects. Safety Systems, Manuals, and Regulatory Compliance The Used Case Sealer APSOL 3500 bph includes safety systems that protect operators during operation and maintenance. In particular, safety barriers, emergency stop buttons, and certified electronic controls ensure compliance with European workplace safety regulations. Additionally, APSOL supplies the machine with comprehensive manuals covering installation, maintenance, and troubleshooting. Consequently, technicians can integrate and operate the machine efficiently from day one. Beyond basic documentation, the manuals also contain detailed schematics and recommended service intervals.

Condition: used, Year of construction: 2007, Used Case Packer Apsol MCP2 3500 bph General Features of the Used Case Packer Apsol MCP2 3500 bph Klslhccqowimnasrou APSOL built the Used Case Packer Apsol MCP2 3500 bph in 2007 as an automatic case packing machine for glass bottles. This model ensures reliable operation and supports a wide range of packaging configurations. Consequently, high-efficiency bottling lines can easily integrate this unit, as it remains fully operational and ready for use. In addition, its compact design allows manufacturers to optimize floor space without compromising performance. Performance and Format Configuration The Used Case Packer Apsol MCP2 3500 bph processes up to 3500 bottles per hour, maintaining consistent output even under demanding production schedules. Specifically, it handles bottles in 0.50 L, 0.75 L, and 1 L formats, packed in 4×3 and 3×2 case layouts. Therefore, operators can switch between formats with minimal downtime. As a result, the machine offers remarkable flexibility for producers of wine, oil, and other glass-bottled liquids. Moreover, the system supports both small and medium production batches, which adds to its versatility. Gripping System and Number of Heads The gripping system uses bell-shaped suction heads with air chambers, which apply pneumatic pressure to move glass containers gently. This way, the machine prevents damage during the pick-and-place process. Notably, it features two gripping heads operating in parallel, which significantly increases throughput. Additionally, the dual-head system distributes workload evenly, thereby enhancing mechanical longevity. In particular, this setup proves effective when handling fragile or tall bottles. Automation and Control System OMRON and TOSHIBA programmable logic controllers (PLCs) control the Used Case Packer Apsol MCP2 3500 bph, ensuring high automation reliability and ease of maintenance. Furthermore, technicians can quickly configure parameters thanks to the intuitive interface. Because of this, the machine adapts smoothly to diverse production scenarios. Operators access the control interface on the right-hand side, which improves ergonomics and reduces operational fatigue. Equally important, the PLC architecture allows remote diagnostics and rapid intervention in case of faults. Safety, Dimensions, and Power Supply The machine includes safety guards that comply with European regulations, thus ensuring operator protection. To illustrate, it features interlocked doors and emergency stop systems. It measures 3000 mm in length, 2400 mm in depth, and 2500 mm in height. In terms of energy, the unit operates on a 400 V, 50 Hz power supply and consumes 11 kW. Altogether, these features make the Used Case Packer Apsol MCP2 3500 bph a robust and scalable choice for mid-to-high-capacity bottling lines. Ultimately, the model combines mechanical reliability with flexible automation, making it a strategic investment for modern facilities.

Condition: used, Year of construction: 1997, Used Filling Monoblock Metalnova for still and sparkling water 12000 bph The Used Filling Monoblock Metalnova for still and sparkling water 12000 bph, model LG, offers a bottling solution designed to process still and sparkling water in 2-liter containers, with a production capacity of 12,000 bottles per hour. Manufactured in 1997, the machine is currently dismantled and in storage. It operates in a counterclockwise direction and supports both PET and glass containers, thereby ensuring flexibility for mixed-format bottling lines. Moreover, its design allows seamless integration into existing production environments. Monoblock Configuration and Bottle Rinsing Process The monoblock begins with a rinsing unit equipped with 60 grippers, which has been engineered to clean containers thoroughly before filling. Notably, the system performs two treatment phases, which not only remove impurities but also prepare each container for the subsequent filling stage. As a result, the unit maintains consistent hygiene standards while sustaining high throughput. In addition, the rinsing module integrates directly into the Used Filling Monoblock Metalnova for still and sparkling water 12000 bph, thereby ensuring accurate container positioning for downstream operations. Kslhjwimm Aeccqrelu Isobaric Filling System with Traditional Valve Technology At the core of the Used Filling Monoblock Metalnova for still and sparkling water 12000 bph lies an isobaric filler equipped with 60 valves. The system, in particular, uses traditional isobaric valves, which allow the machine to accurately manage both carbonated and non-carbonated liquids. Consequently, it maintains pressure stability throughout the entire filling process. In doing so, it minimizes foam generation and preserves CO₂ in sparkling beverages. Furthermore, this configuration makes the filler suitable for dual-function production lines that handle a wide range of water products with precision and efficiency. AROL Capper with Three-Roller Threading System for Plastic Screw Caps Following the filling phase, the AROL capping unit applies plastic screw caps using a three-roller threading mechanism (“3 principles Alaska”). This component includes 10 heads, each engineered to ensure uniform closure at high speeds. More specifically, the “3 principles” system uses three threading rollers to apply consistent torque and secure sealing. Thus, the capper guarantees reliable performance across various formats and cap types. It is especially effective for high-volume operations. Additionally, it aligns perfectly with the performance characteristics of the Used Filling Monoblock Metalnova for still and sparkling water 12000 bph, maintaining closure accuracy and product integrity. Electronic Control and Spare Parts Availability The machine uses a Siemens PLC to control its various operational stages. This platform not only ensures system stability but also allows for easy diagnostics and interface integration.

Condition: used, Year of construction: 2003, Used Automatic Depalletizer ACMI  1600 plastic crates/hour The Used Automatic Depalletizer ACMI 1600 plastic crates/hour, model Rasar D180, operates as a fully automatic system for bottom-feed depalletizing of 1-liter glass bottles packed in 12-bottle plastic crates. Specifically designed for high-speed bottling lines, the system processes up to 1600 boxes par hour. Moreover, its modular frame allows seamless integration into existing production lines. Although it is currently dismantled and in storage, the unit remains in full working condition, ready for reinstallation. Kolhcewiml Escqrelu Depalletizing Structure and Operating Mode The Used Automatic Depalletizer ACMI 1600 plastic crates/hour utilizes a conventional automatic vertical structure to handle pallet loading from below. This configuration, therefore, ensures optimal stability and precision during the handling of glass containers. In addition, the machine includes an integrated pallet magazine, which automatically feeds pallets into the process without requiring manual assistance. Consequently, the system improves line efficiency and minimizes stoppage time. Furthermore, thanks to its automated design, the machine reduces labor dependency and enhances repeatability. Container Compatibility and Format Handling in the ACMI depalletizer This machine specifically handles 1-liter glass bottles arranged in 12-bottle plastic crates. As such, it suits production lines that deal with fragile, heavy, or pressurized containers. In terms of compatibility, the Used Automatic Depalletizer ACMI 1600 plastic crates/hour meets standard industry requirements for crate and bottle handling. Additionally, it ensures accurate transfer from pallet to crate and then to the conveyor system. Not only does the equipment offer reliable performance, but it also reduces the risk of damage during transfer. Similarly, its precise control mechanisms help optimize changeovers when switching formats. Safety Features and Electronic Control of the ACMI depalletizer Engineers equipped the machine with certified safety systems that meet all current regulations for automated equipment. These features include physical guarding, sensor-based detection, and emergency stop functions in critical zones. As a result, the machine ensures safe operation in industrial environments. The Used Automatic Depalletizer ACMI 1600 plastic crates/hourruns under the control of a Siemens PLC, which manages operations through real-time sequencing and diagnostics. In particular, the PLC simplifies fault detection, thereby reducing downtime. Moreover, its open architecture supports easy integration into plant-wide SCADA systems. Therefore, users benefit from complete process visibility and responsive control. Technical Documentation and Operational Status In terms of documentation, the Used Automatic Depalletizer ACMI 1600 plastic crates/hour includes full technical manuals. These documents cover installation, electrical schematics, PLC logic, and communication interfaces.

Condition: used, Year of construction: 2007, Used Palletizer ACMI RASAR P180 1600 plastic crates – hour General Features of the Automatic Palletizer The Used Palletizer ACMI RASAR P180 1600 plastic crates – hour is a conventional automatic low-level palletizer designed to optimize end-of-line operations in high-speed bottling processes. Specifically, the Italian manufacturer ACMI built this model in 2007. As a result, it delivers a nominal capacity of 1600 plastic crates/hour, which ensures high productivity. In particular, it suits bottling lines that handle 1-liter formats in both glass and PET. Moreover, the system prioritizes reliability and speed in demanding industrial settings. Compatibility with Bottle Crates and Pallets The Used Palletizer ACMI RASAR P180 1600 plastic crates – hour efficiently handles crates containing 12 glass bottles. Consequently, it proves ideal for beverage production environments where crate-based transport is standard. Furthermore, the machine processes standard CP1 pallets (1000×1200 mm), ensuring compatibility with common logistics solutions. In addition, it includes an integrated pallet magazine, which significantly reduces the need for manual intervention. This, in turn, contributes to continuous and automated operation. As such, it streamlines the entire end-of-line workflow. Movement System and Automation This model features a low-level movement system. Not only does this simplify the mechanical layout, but it also facilitates maintenance access. Therefore, operators can perform inspections and servicing more efficiently. A Siemens PLC manages the palletizing cycle, thereby guaranteeing precise control and high reliability. Additionally, the PLC allows seamless integration with upstream and downstream equipment. In short, the automation setup supports complex configurations while maintaining ease of use. Safety Functions and Technical Documentation The Used Palletizer ACMI RASAR P180 1600 plastic crates-  hour includes all required safety features to comply with current industrial regulations. Specifically, it comes with physical guards, presence sensors, and interlocks. Thanks to these features, the system protects operators during operation and maintenance. Besides, it includes complete technical manuals. These documents, in turn, support technicians during installation, configuration, and servicing. Consequently, the equipment offers not only performance but also compliance and maintainability. Current Condition and Recommissioning Potential Currently, technicians have dismantled the Used Palletizer ACMI RASAR P180 1600 plastic crates – hour. Therefore, transport and storage become significantly easier. Additionally, the modular construction reduces both time and effort during recommissioning. As a result, companies can quickly reintegrate the machine into existing production lines. Technical Conclusion of the Used Palletizer ACMI Klelowimlxohccqrju The Used Palletizer ACMI RASAR P180 1600 plastic crates – hour offers a highly specialized and reliable solution for manufacturers who need high-capacity palletizing systems.

Condition: used, operating hours: 1,800 h, Used Bottling Line for champagne, sparkling and still wine 4000 bph Product Compatibility and Filling Technology This bottling line processes still wine, sparkling wine, and champagne with high efficiency. Specifically, it handles only glass bottles and uses an isobaric filling system, which ensures precise control when filling pressurized liquids, such as sparkling products. As a result, wineries that produce multiple wine types with different physical and chemical properties can rely on this line for consistent, adaptable operation. In other words, the system addresses diverse product demands without compromising output quality. Performance Output by Bottle Format Depending on the bottle format, the line delivers different outputs. It processes both 0.20l and 0,375l bottles at 4,500 bottles per hour. Meanwhile, it handles 0,75l bottles at 4,000 bottles per hour and 1.5l bottles at 2,000 bottles per hour. Therefore, this production speed suits medium-scale wineries that require flexibility while maintaining industrial performance. Commissioning, Runtime, and Immediate Availability Kjlowgw Dgshccqrolu Technicians installed the line in 2022. Since that time, it has operated for 1,800 hours and produced approximately 2,400,000 bottles. The system continues to run in production, which means it remains in good operational condition. Furthermore, its immediate availability offers an advantage to wineries needing rapid deployment. Because of this, buyers can integrate the equipment without significant downtime. Primary Bottling Block: Depalletizing, Rinsing, Filling, and Capping The process starts with a Duetti Packaging depalletizer, model M, which automatically feeds empty bottles into the system. Subsequently, the GAI monoblock, model 4033RES-HP-A01, performs rinsing, filling, and capping in a single integrated unit. The dual-stage rinser (water + gas) uses 16 grippers to sanitize bottles. A high-pressure electropneumatic filler with 24 valves carries out isobaric filling. Notably, the 3-head rotary corker applies straight corks, champagne-style mushroom corks, plastic closures, and aluminum screw caps. Moreover, the monoblock includes multi-format screws, motorized guide adjustments, dummy bottles for internal rinser sterilization, and a solenoid valve kit to switch between gas and cleaning liquid inputs. Altogether, this configuration provides high precision, minimal changeover time, and excellent bottle handling. CIP and Quality Control: Cleaning and Inspection Systems To maintain hygiene, the WIN&TECH CIP unit, model Win&Guard C 23.05, manages automatic cleaning via a steam-water heat exchanger and a three-stage filtration system across two independent circuits. Additionally, this system allows operators to sanitize the internal components between production runs without disassembly. At the same time, the CMP inspection unit, model CV-MUF108, performs continuous quality control.

Condition: used, Year of construction: 2010, Used CIP Tetra Pak year 2010 15T/h The Used CIP Tetra Pak year 2010 15T/h, model Tetra Alcip 1, performs Cleaning in Place (CIP) to automate the cleaning process in bottling and food processing plants. Consequently, this system ensures an effective sanitation cycle without requiring production line disassembly, optimizing downtime and reducing water and detergent consumption. Tetra Pak built the Used CIP Tetra Pak year 2010 15T/h in 2010. Specifically, its 15-ton-per-hour operational capacity makes it suitable for high-productivity plants while ensuring hygiene standards that comply with food and beverage industry regulations. Technical Features of the Used CIP Tetra Pak year 2010 15T/h The Tetra Alcip 1 applies a controlled washing cycle to remove organic and inorganic residues from production circuits. In particular, the system integrates separate tanks for water, alkaline detergent, and acid, and it automatically regulates temperature, chemical concentration, and washing time based on plant requirements. As a result, it enhances the efficiency of cleaning operations. Moreover, the Used CIP Tetra Pak year 2010 15T/h automates the cleaning process, reducing cross-contamination risks and improving production efficiency. Additionally, the system allows operators to configure different washing parameters, which enables adaptation to specific production needs and ensures thorough cleaning of filling lines, pipelines, and heat exchangers. Safety and Process Control The system includes advanced safety features, such as: Sensors that continuously monitor detergent concentration. Temperature and pressure controls throughout the cleaning cycle, ensuring optimal performance. Alarm systems that detect and manage sanitation process anomalies, thereby preventing potential failures. As a result, these features ensure this Used CIP operates reliably, minimizing operational errors and optimizing water and chemical consumption. Furthermore, the system’s automated monitoring enhances safety while reducing maintenance requirements. Operational Advantages Kljlhccqswga Iuersu Using this Used CIP Tetra Pak  enhances plant productivity in multiple ways. First and foremost, it reduces downtime: the continuous washing system completes fast cleaning cycles without requiring component disassembly. Moreover, it optimizes resource usage: the automatic detergent dosing system prevents chemical waste. Additionally, it ensures regulatory compliance: the system meets high hygiene standards and complies with industry regulations. At the same time, the automated nature of this system helps manufacturers streamline their cleaning procedures. Consequently, businesses benefit from both improved production continuity and reduced operational costs. Likewise, the ability to customize cleaning parameters provides greater control over sanitization processes. Conclusion In summary, this Used CIP Tetra Pak provides an efficient and reliable solution for sanitizing bottling and food production plants.