Concrete mixer truck

VOLVO FM420 Wechselsystem 3-S-Kipper Betonmischer AHK

Condition: used, turning diameter over bed 2400 mm turning diameter over slide rest 2200 mm turning length 10000 mm power capacity 185 kW faceplate diameter 1650 mm turning speeds 1,5 -150 U/min max. workpiece weight 70000 kg clamping diameter 1400 mm Technical data Working range Maximum turning diameter over support: 2200 mm Maximum swing diameter over bed: 2400 mm Maximum turning length: 10,000 mm Clamping diameter in the headstock faceplate: 300 - 1,600 mm with special jaws up to 2,050 mm Clamping diameter in the tailstock faceplate: 300 - 1,400 mm Maximum workpiece weight: 70000 kg Main drive, faceplate Faceplate diameter: 2000 mm Faceplate speeds, continuously adjustable in 4 stages: 1.5 - 150 rpm Maximum torque at rated speed: 220,000 Nm Drive power of main motor: 185 kW Flange centre point angle: 70° Supports Travel of the plunge slide: 500 mm Travel of the face slide: 1400 mm Quick adjustment, longitudinal: 2000 mm/min Quick adjustment, face: 800 mm/min Infinitely variable feed, longitudinal: 0.6 - 300 mm/min Infinitely variable feed, face: 0.3 - 120 mm/min Max. cutting force at support: 20,000 kg Tailstock Faceplate diameter (removable): 1650 mm Faceplate clamping diameter: 1400 mm Flange centre point angle: 70° Quick adjustment: 1250 mm/min Special equipment Copying device for first support Copying length 8500 mm Max. copying depth in one pass 500 mm Boring device: Boring bar 460 x 390 mm Drilling diameter 600 - 1000 mm Maximum drilling depth in one pass 2700 mm At Ks of 200 kp/mm² - s max. = 1.5 mm/rev a = max. chip cross-section 30 mm² at a projection of 1000 mm Reduced chip cross-section with increasing drilling depth A guide ruler for cone turning, adjustment angle up to 8° and a maximum cone length (in one pass) of 2000 mm, adjustment accuracy ± 5 minutes. A guide ruler for cone turning, adjustment angle up to 15° and a maximum cone length Gsdjxddvnopfx Admeil (in one pass) of 1000 mm, adjustment accuracy ± 5 minutes. 125 kg auxiliary crane on spindle box.

Condition: excellent (used), Year of manufacture: 1991 Gsdpfxswq Dpqo Admoil Model: ITPS III Serial number: ITPS 80C 25 P1C226 Maximum pressing force: 1800 kN Working stroke: 115 mm Power supply: 415 V, 50 Hz, 3 phases Rated current: 119 A Installed power: 18.5 kW Machine weight: 4940 kg Inventory number: 9.14 Control: Delem DA-65R The machine starts up, but the control unit does not respond to commands. The previous owner replaced the original AMADA control with a DELEM unit.

Year of construction: 2011, condition: reconditioned (used), Boschert tool grinding machine EASY SHARP Equipped for Trumpf tooling system (Amada system optional) Machine for punching tool maintenance with cooling system and especially powerful motor, therefore also suitable for use with diamond grinding wheels. Used machine is currently being overhauled Equipment for Trumpf tooling system up to size III Accessories: Tool holder for punch flat and whisper Die holders for size I, II and III Gisdpfxeid I T Is Admol New corundum grinding wheel Dressing diamond Cooling system and machine base revised Technical data: Grinding wheel diameter 175 mm height adjustment 150 mm working area 400 x 150 mm motor power 2,2 kW Motor speed 2825 rpm Optional adapter for Amada system available Pictures similar

Condition: new, Year of construction: 2025, machine/vehicle number: 988906827, fully mobile concrete fuel station Frumecar Fastmix * THE STRESSED GAS STATION * Gjdjhd I Smspfx Admoil - Year of construction: New - 2-4 chambers with 7-14 m³ capacity - capacity: 14-25 m³-h depending on mixer size - mixer size: 0,5 m³ - 0,75 m³ -1,0 m³ - Concrete software from Siemens with self-service terminal and new barcode method and EC card terminal - concrete discharge conveyor 9m length - Cement silo 32 to. incl. cement screw conveyor - installation, commissioning and training incl. - 2 years warranty - Highest quality plant on the market. All components produced in produced. Electric motors and gearboxes from Siemens installed. Other plant components from the market leader VAM. Input errors and mistakes in this offer are expressly reserved. Only the specific agreements in the order confirmation or in the purchase contract are decisive. more construction machines and mixing plants on our website Further information Purpose: construction, Usable material: concrete, General condition: very good, Technical condition: very good, Visual condition: very good,

Condition: new, Year of construction: 2024, == Exhibition machine == ALZMETALL column drilling machine ALZSTAR 40 SV with coolant unit B (option 25) Gsdpfsd Hy Elsx Admsil (consisting of separate tank (33l), pump with motor protection switch, complete fitting) and LED machine light Standard equipment: Mushroom pushbutton, reversing switch (for clockwise and anticlockwise rotation), motor protection switch Infinitely variable speed adjustment, digital speed display, feed overload protection, protection class IP54, connection plug Spindle protection with electrical fuse Technical data: Drilling capacity steel E335 (St 60) 40 mm Thread cutting: Steel E335 (St 60) M 24 Cast iron EN-GJL-200 (GG20) M 30 Short spindle MK 3 Spindle stroke 120 mm Projection 293 mm Column diameter 115 mm Machine table, usable support 514 x 360 mm T-slots, number x width x distance 2 x 14 x 224 mm Spindle-to-table distance min./max. 117/701 mm Feed rate 0.10 + 0.20 mm/rev Machine height without options approx. 1840 mm Net weight approx. 285 kg Drive stepless Motor 1500 / 3000 rpm Power 1.45 / 1.9 kW Spindle speed 160-2250 rpm

Condition: new, Year of construction: 2026, EuromixMTP - Roll-off tipper - Superstructures - Truck mixer EUROMIX MTP - Truck mixer superstructure EM 5 L lightweight construction Model: EM 5 L * Nominal volume 5m³ ready-mixed concrete Gedpfjvv D E Rsx Admjil * Mixing drum in lightweight construction * Mixing drum in lightweight design made of HARDOX S450 * Mixing spirals in lightweight design made of HARDOX S50 * Gearbox made by ZF P4300 * Hydraulic pump Bosch Rexroth * Hydraulic motor Bosch Rexroth * Integrated oil cooling system * Mechanical mixing control and electric start/stop * Compressed air water system * Water connection on the stand platform with hose line * Water filling line, one-sided with C-coupling * Mixing drum with a service flap * Step ladder with stand platform * Rubber attachment on the filling funnel * Swiveling, single-arm discharge chute made of steel * Wear plates in the filling funnel, discharge bowl and swivel cord * Drum lock to secure the drum during maintenance work * Polyurethane primer * with emergency stop function in accordance with EU safety technology * steel wings over the rear axles * 2x extension gutters made of steel or plastic * Water system * 500l water tank (compressed air) * Steel water tank * Shut-off valve mounted below the water tank in the filling line * Water connection "C" coupling, * Operation & electrics * Mixer operation - mechanical rear * Start-stop system (with EDC If you have any further questions, our team is available in the following languages. * We speak German * We speak English * Nous parlons français * Mówimy po polsku * ?? ????? ????? ????? * Govorimo Srpskohrvatski

Condition: used, Year of construction: 2019, operating hours: 1,360 h, Mini excavator CASE CX26C, * Year of manufacture 2019, * 1360 operating hours, * Heating, * Air conditioning, Gedsurfkcepfx Admjil * Rubber tracks, * Dozer blade, * Quick coupler

Condition: good (used), Plasma cutting machine, plasma cutter, for plasma cutting system -Manufacturer: Hypertherm Gijdpfx Adjwd Tg Somol -Type: HySpeed HT2000LHF -Equipment: with hose package and cutting nozzle head -Max. cutting current: 200 A -Dimensions: 1100/720/H1040 mm -Weight: 459 kg

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: 693068, overall weight: 7,300 kg, power: 30 kW (40.79 HP), Walter Helitronic Vision CNC Tool & Cutter Grinder with Pallet Loader Universal tool and cutter grinder (CNC controlled) Made by Walter, model Helitronic Vision, s/n 693068, year 2008 Description: Suitable to manufacture and regrind metal and woodworking tools of all kinds. Can be viewed under power. Specifications: • Longitudinal movement (X-axis) 480 mm • Y axis vertical movement 320 mm • Z-axis transverse movement 700 mm Gisdsuqzdpepfx Admjl • Rotary table swivel range C-axis +/- 200 ° • Workpiece Holder ISO 50 • Max. Workpiece diameter 320 mm • Workpiece length circumferential grinding 370 mm • Workpiece length for face machining 320 mm • Accuracy linear resolution 0.0001 mm • Radial resolution 0.0001 ° • Diameter of the spindle 100 mm • Grinding wheel mount: HSK50 • Diameter of the grinding wheel 200 mm • Grinding spindle speed 0 – 12,000 rpm., • Top performance 30 kW • Connected load 35 kW (460 V / 60 Hz) • Weight approx. 7,100 kg • Dimensions L x W x H 3649 x 2490 x 2301 mm Accessories: • Does not include wheel opening stick fixture seen in the pictures • Stepless speed control, probe, pneumatic workpiece clamping • Electrostatic mist extractor • Fire extinguishing system • Oil collecting pan, 2 grinding wheel flanges, Complete set of Manuals • Turmoil Drive Chiller • Loader Pallets: 8pcs – 3/16”, 1/4”, 5/16”, 3/8”, 1/2”, 5/8”, 3/4”, 1-1/4” • 10pcs - HSK Wheel Arbors Software: • Windows XP Pro Svc Pack 3 • Tool Studio V3.3 • The computer was upgraded & is very fast rendering tools in Tool Studio Condition: • Excellent condition, very accurate & consistent. October 2023 Y axis Complete rebuilt, Linear motor, rails, Compensation Cylinder, Festo Booster Pump done by United Grinding. • 1 Micron Filtration system was used on the machine (not included), so it’s been kept extremely clean • We can load onto a flatdeck for shipping for $1200. We can also provide shipping quotes if you would like & crating for Sea Freight shipping.

Condition: used, mileage: 285,000 km, first registration: 06/2012, brakes: retarder, Equipment: ABS, electronic stability program (ESP),