Straightening and cut machine

VITARI NR 10

Condition: used, Year of construction: 2000, functionality: fully functional, machine/vehicle number: D08L/8034, Offer Number: D08L/8034 Machinetype: straightening and cutting machine Make: WAFIOS Type: R31 Constr. year: 2000 wire diameter range: 1,5-7,0mm cutting length: 3000 mm speed - meters/min: 5-120 Lodpfxswi Th Ts Ad Aerk Location: In our warehouse

Condition: good (used), Year of construction: 2000, table width: 1,000 mm, table length: 1,800 mm, ram plate width: 600 mm, total length: 25,000 mm, total width: 27,000 mm, total height: 47,000 mm, overall weight: 43,000 kg, die cushion stroke: 200 mm, Siemens Simatic OP 27 control system Lodpfx Adetiwgij Asrk Light barrier Sick Separate control cabinet Ritta Side passages Ground level installation

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC Lredpewp Rqfjfx Ad Aek The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: excellent (used), Year of construction: 1986, functionality: fully functional, equipped with: 1 slide feeding system right hand side 1 eccentricpress 250 kN 4 standard slide units 1 narrow slide units 1 cam shaft working range: wire diameter range: 0,5 - 5,0 mm stripmetal width: max. 40 mm feeding length: up to 320 mm Lodotzlzaopfx Ad Ajrk outout: up to 135/min

Condition: used, Year of construction: 1994, Technical details: number of spindles: 8 spindle passage: 32 mm Article: cam-controlled multi-spindle automatic lathe Manufacturer: Schütte Type: AF32 S DNT Yob: 1994 Eight-spindle automatic lathe with 8 main spindles max. nominal diameter D=32mm control: Siemens SIMATIC S7 electronic cam control Balluff gripper in position 8 for backworking CNC cross slide position 6 CNC cross slide position 7 Workpiece belt Coolant cooling Schimpke Chip conveyor with magnetic separator Tapping couplings The tooling shown may differ from the scope of delivery! Please, contact us for getting more information and pictures on mail(at) or Lrjdpel Su Rxjfx Ad Ask *

Condition: new, Year of construction: 2025, Entry-level sheet fiber laser metal cutting machine Lower laser cutting cost and easy operation The modular cutting machine table with stiffeners saves time for disassambly and improves convenience and rigidity. The special fiber laser nozzle and cutting process ensure faster carbon steel oxygen cutting, more gas-saving low-pressure stainless steel nitrogen cutting, and better-quality carbon steel air cutting. Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Applicable Material: metal Condition: New Laser Type: Fiber Laser Laser Power: 1000W, 1500W, 2000W, 3000W Cutting Area: 3000*1524mm Positioning accuracy: ±0.05mm Repositioning accuracy: ±0.03mm Cutting Speed: 0-100m/min Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING Lrjdpshwrgtsfx Ad Aok

Condition: like new (used), Year of construction: 2009, functionality: fully functional, We are selling this grinding machine, which is connected and available for testing. Lredpexxrzzefx Ad Aok Machine parameters: - Grinding of rotational parts clamped between centers with an accuracy of 0.001 mm - Max. swing diameter: 0–1,450 mm - Max. turning length: 6,000 mm - Max. workpiece weight: 20,000 kg (25,000 kg with steady rests) - Grinding wheel diameter: 915 mm - Wheel width: 100 mm - Non-contact measurement of dimensions, tolerances, and workpiece geometry, including printout of measurement protocol - 100% ultrasonic measurement possible - CNC control with capability for profile grinding (taper, concave and convex, CVC) - Grinding of ceramic and metallic coatings using diamond and ceramic grinding wheels The machine is currently completing an order.

Year of construction: 2026, condition: new, functionality: fully functional, Complete plastics recycling line for films and fibre materials from Taiwan leading Plastics Recycling Machinery manufacturer. GENIUS Machinery Co who have more than 30 years of recycling extruder production and experience. Extruder can be fed without size reduction or shredding.. Materials in baled, loose or reel form can be fed. Line can be supplied complete with Belt conveyor, Cutter compactor, Main extruder, Filtration system, (variety of types to suit requirements), Hot pellet die-face cutting device, Centrifugal pellet dryer, Vibrating screener, Storage silo for pellets. Additional ancillary equipment can be supplied . A two stage " Cascade" version is also available for heavily printed films, or very dirty films requiring double filtration. Alternative sizes from 100 kgs per hr up to 1200 kgs per hr can be offered. Full sales and support and training is available in UK and Europe for these extremely modern and economic machines. Lrsdpfx Adowg R Rto Aek

Condition: used, Year of construction: 2026, operating hours: 15 h, functionality: fully functional, machine/vehicle number: 204065, Used machine CNC cutter/plotter Cutting area in X and Y: 3,500 x 2,100 mm. Multifunctional CAM cutting system in CNC knife technology for 2D cutting of leather, fabric, technical textiles, foam and other flat, semi-flexible or rigid, non-metallic materials Equipment of the used machine • 1 cutting bridge and 1 multifunctional tool head The machine is sold with one driven circular knife, electric oscillating knife and one Milling Head + exhaust • Multifunctional tool head to hold max. 2 interchangeable tools • powerful vacuum blower for fixing the material • Standard equipped with gray conveyor table (Conveyor). Green-blue exchange conveyor possible (offers high contrast for dark materials) Can be extended with other tools (on request): • EOT electric oscillating blade • POT pneumatic oscillating knife • PRT rotating blade • UCT universal blade • KCT Kiss-Cut tool • CTT creasing tool • V-Cut angle-cut cutting blade • Punching tool for pinches or holes • Printer mark detection • Camera registration Easy-to-use function • Easy interchangeable cutting tools, "PLUG & CUT • Intuitive user interface • Easy blade change • Vacuum zones can be activated with a click Fast amortization • Low cost with high added value • Best material utilization through nest expert software modules (not included in equipment) • High velocity • Constant precision Data: Lredpfx Aoif Ek Rjd Aek • Short cutting times due to high positioning speed up to 90 m/min. • Repeatabiliy +/- 0.25 mm • Cuts single or multiple layers • Suitable for both single ply and multi ply or sheet goods and roll goods (can be extended with suitable unwinder) (Product photo as example) The machine is CE certified.

Condition: used, Technical details: wire diameter - max.: 9,0 mm wire diameter - min.: 2,0 mm voltage: 380 V / 50 Hz V control voltage: 220 V Total power requirement: 18 kW Weight approx.: 5,0 t dimensions: Schmiermittelanlage: 830 x 650 x 1000 mm dimension machine xH: 3,3 x 1,5 x 1,45 m dimensions electric cabinet LxWxH: 0,7 x 1,5 x 1,75 m WIRING AND CUTTING MACHINE / MACHINE WAS UPGRADED WITH A NEW CONTROL SYSTEM IN 2000 A programmable, electronically-hydraulically controlled universal spring coiling machine for the production of right and left-hand tension and compression springs as well as torsion springs. The springs can be produced with any pitch and shape of spring body. Output max. 90 pieces/min. Outer spring Ø 10 - 120 mm Unlimited wire feed length, speed = 27 - 80 m/min. Coiling device: two-finger system wire thickness Ø 2.0 - 9.0 mm; spring outer Ø Ø 10 - 120 mm Single-finger system: wire thickness Ø 3.0 - 7.0 mm; spring outer Ø max. Ø 60 mm Equipment: 5x feed rollers, wire holder 3 mm two-finger Spring length measuring device LION PRECISION-PANTHER Wire roller holder POST, motor-driven, mandrel holder Ø 1,400 mm Lubrication system Control cabinet cooler RITA Hydraulic unit Optional many accessories and/or spare parts! i.D. Lrjdpovc Aklsfx Ad Aok *