Mesh welder

PRATTO Starweld PO

Year of construction: 1999, condition: good (used), Nail lenght range - 50 - 90mm Speed - 100 nails/sec. ( frequency regulator ) Management - PLC Simens S5 Njdpfxedmbp Ue Aa Eswr

Condition: good (used), Year of construction: 1979, Complete production line for Technical and Commercial Chain Manufacturer - WAFIOS / VITARI / DANIELI / IPSEN Year - 1979/1989 Factory Consists : - Welding machines 14 pieces - Bending machines 10 pieces - Bending + welding machines - 2 pieces ( Wafios KEH3 +KER3 ; Wafios KEH5 + KER5 ) - Wire drawing line 7 blocks - Danieli with spooler - Cementation furnace - Annealing furnace Lots of sapare parts Njdpfxoqy E I Uj Aa Ejwr

Condition: reconditioned (used), Stock - No.: 2553 1 used, partly overhauled and functionally tested Single-Screw Extruder, equipped with: Material hopper loader Extruder BATTENFELD Typ UNI-EX 1-75-25 B Screw - Ø 75 mm – 25 L/D, Cylinder Air-cooled Extruder-Motor 120 kW – DC ( overhauled ) Screw –speed up to 130 r.p.m. additional Temperature controllers for down-stream equipment Nwsdpjiyyndefx Aa Eor Control-Board with melt-pressure sensor / Display. Inspectiuon visist / trial-run shortly by appointment in our workshop Wuppertal Germany possible. We can offer, installed to this extruder: > screen-pack-changer > pelletizing ( strand, hot-face or waterring ) > other equipment Send us your inquiry. More extruder and complete pelletizing lines ex our workshop Wuppertal, send us your inquiry or visit us, you´re welcome

Year of construction: 2022, condition: new, This system operates in automatic mode. The transfer of pallets between production line and curing area is carried out by Finger Car. 1 operator supervises the production process via control panel equipped with 4 different monitor, pc system. Automation system software has user-friendly interface and can be translated into customer’s preferred language. Production line requires the construction of curing chambers with racks. Steam curing is recommended for working in one shift and is mandatory for working in two shifts. Nsdpfoibcycox Aa Eewr Transfer of production pallets with green products to the curing chambers as well as the transfer of pallets with cured products to the cubing station is carried out by automatic pallet transport system known as Finger Car. Finger car consists of lower and upper electric trolleys, which move along a set of rails built perpendicularly to the concrete block production line. The upper trolley has steel forks for grabbing and holding pallets. It transfers concrete products to the curing chambers, going inside each chamber to place pallets with wet products on racks to cure. On its way back it takes a stack of pallets with cured products and loads it into the lowerator. The price given as 1.200.000 USD includes all the machine equipments, concrete batching plant and 3000 pallet rack system. It is very special offer for August 2022!

Condition: new, Year of construction: 2023, B-Series is suitable for bending your steel into the desired shape. B-Series: B26, B36, B45X1, B50 BS-Series (Double Bending): BS36, BS45, BS50, BS60 (MG65 PRO) Product information: - Voltage: 380 V (16 A) - Motor Power: 2,2 kW - 6 kW - Ideal for your construction company or also for your construction sites Nedjm Shffjpfx Aa Eswr - Left & Right Bending possible (in the BS-Models) - In addition to the individual bending process, a bending sequence can also be programmed - Head for different reinforcing steel Ø are included in the accessories (incl. accessories) - Possible in automatic or manual mode - Bending capacities depending on steel strength according to table (see pictures) - Optional available with digital control panel - Net weight: 215 kg - 850 kg Shipping: Europe-wide (self-collection also possible) If you have any questions, please do not hesitate to contact us!

Condition: new, Best price 4499 Eur (EXW Jonava, Lithuania) Dimension of sliding table- 2200x375mm Gross cut capacity- 1500mm Width of cut between saw blade and rip fence - 1140mm Saw blade diameter - 400mm Nwedpodnxydofx Aa Eor Height of cut (90°) - 115mm Height of cut (45°)- 105mm Speed of main saw spindle - 4500/6000rpm Main spindle diameter - 30mm Tilting saw blade - 0-45º Saws lifting, up and down, electrical control. Main motor - 5,5 kW Scoring saw blade diameter - 120mm Speed of scoring saw blade - 7000-8000rpm Scoring saw diameter - 20mm Scoring motor - 1,1 kW Weight: 700 kg * Using the blade 400mm, the smaller should be removed. Reduced saw blade should be used with not more than 350 mm main shield.

Condition: ready for operation (used), technical Details: Speed - 130m/min. , Year - 2006, run out table - 6 m Wire diameter range 4-12 mm Nwedstndgpjpfx Aa Esr

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2005, Fully operational block production plant equipped for both concrete and lightweight expanded clay aggregate (LECA) block manufacturing. Currently in use — production process can be demonstrated on site. Key Features: Metalika concrete mixer (2022) with integrated precise moisture sensor Many new moulds available Average production capacity: • 270 m² of pavement blocks per shift • 50 m³ of LECA blocks per shift Technical Specifications: Upper and lower vibration system 1.5 m³ ready-concrete hopper 0.75 m³ mixer with 11 kW motor 8 m³ material bunker Hydraulic power unit Water metering system Precise moisture meter Adjustable/variable production speed Automatic production pallet de-stacking and stacking Pneumatic palletizing gripper Large quantity of production pallets included Current molds in stock (size in mm): Building blocks (LECA blocks): 1) 500x300x200 2) 400x200x200 Pavement stones: 1) 200x100x50 2) 200x100x60 3) 200x100x80 4) 180x120x60 5) 180x120x80 6) 240x60x80 7) 300x300x60+300x150x60+150x150x60 8) 240x240x60+240x120x60+180x120x60+120x120x60+120x60x60 9) 300x300x80+450x300x80 Nwjdpfxjwdf U Uj Aa Eer Kerb stones: 1) 800x200x70

Condition: reconditioned (used), Year of construction: 2008, functionality: fully functional, turning length: 1,250 mm, turning diameter over cross slide: 500 mm, turning diameter: 390 mm, spindle speed (max.): 5,000 rpm, spindle bore: 65 mm, travel distance X-axis: 450 mm, travel distance Y-axis: 200 mm, travel distance Z-axis: 1,300 mm, bar passage: 65 mm, total height: 2,700 mm, total length: 7,000 mm, total width: 3,000 mm, overall weight: 12,000 kg, Equipment: documentation/manual, Manufacturer: DMGMORI Type: CTXbeta1250TC Year of manufacture: 2008 (retrofit in 2022) Control: Siemens 840D Solutionline Njdpfx Aaeubyv Ro Eowr Number of axes: 5 axes Equipment: - automatic tool changer - swivel head as B-axis - belt filter system with internal cooling and chip conveyor - differential pressure clamping main/counter spindle - workpiece collection device - preparation for bar loader (optionally available) Technical data: Max. turning diameter 500 mm X-axis 450 mm Y-axis 100 mm Z-axis 1300 mm B axis 220 ° Spindle bore 65 mm Speed 5000 rpm Spindle power 34 kW Counter spindle speed 6000 rpm Counter spindle passage 52 mm Counter spindle power 20 kW Tool changer 24 B-axis mount HSK 63 B-axis spindle speed 12000 rpm B-axis power 22 kW Installation dimensions approx. L 7000 / W 2300 / H 2300 mm Weight approx. 8,000 kg Chip conveyor: Yes Coolant device: Yes Internal coolant supply: Yes Options: · Full cabin · NC swivel head as B-axis · Coolant device and chip conveyor · Documentation · Geometrically within the new machine tolerances Condition: - Machine fully functional - Geometry within the manufacturer's tolerance for new machines - All wear parts replaced Retrofit 2022: - Linear guides Z1 and Z2/3 replaced - Linear guide Y-axis replaced - Main and counter spindle overhauled - Milling spindle overhauled - B-axis (bearings and clamping) renewed - sliding plates overhauled - hoses and cables overhauled, drag chains revised - cabin doors repainted, viewing windows renewed - maintenance carried out according to manufacturer's specifications

Condition: new, machine/vehicle number: Baureihe GSL 300 / Neumaschine, The cutting mills in the GSL series 300/400 to 300/800 are primarily intended for the shredding of production-related scrap material in the injection molding and blow molding sectors. In addition to the key advantages of the GSL series, the slow-running cutting mills GSL 300/400, GSL 300/600 and GSL 300/800 are particularly suitable for large-area parts, such as car door panels, bumpers or hollow bodies. The "V-arrangement" of the rotor blades keeps the pre-shredded material in the center of the rotor. This significantly reduces wear on the grinding chamber walls when grinding glass fiber reinforced plastics. Material sticking to the side walls is avoided. The staggered arrangement of the rotor disks means that only individual blades are used at any one time, so a higher cutting force is available in each case. Nwodoghgbhspfx Aa Esr