Used Pmh Gmbh Ex20-25D Nitriert for sale (69,011)

Condition: like new (used), functionality: fully functional, Year of construction: 2023, Our compact extruder model EX20-25d Manufacturer: PMH GmbH Screw diameter [mm] 20 Screw length [L/D] 25 Screw speed [min-1] 10-192 Screw nitrided Torque 55Nm Drive Three-phase drive with frequency converter Drive power [kW] 1.1kW Barrel material: nitrided Electrical connection values 3 / N / PE Supply voltage [V] 400V at 50 Hz Control voltage [V] 24V Djdeq R Tkwjpfx Adhjcn Ceramic heating tapes [W] 1200W Number of heating tapes 3 Max. Output approx. 5kg/h Max. Processing temperature [°C] 300

Year of construction: 2026, condition: new, functionality: fully functional, The laboratory extruder model EX20-25d is designed for small-scale material development, small batches, or filament extrusion. It has a plasticising capacity of 5kg/h. Our extruder model is designed with a bimetallic barrel and through-hardened screw, allowing for high-temperature processing (up to 400 degrees). Dedpfjiv H Ekjx Adhscn This enables the processing of abrasive raw materials, engineering plastics, PEEK, metal compounds, ceramics, and fibre-reinforced materials. Inspect available machines at our factory in Königswinter. We can also provide machines in other dimensions.

Condition: excellent (used), Year of construction: 2013, operating hours: 1,000 h, functionality: fully functional, machine/vehicle number: 24480, input voltage: 400 V, The Amandus Kahl flat die pellet press, type 37-850, is a robust industrial machine manufactured by the German machine builder Amandus Kahl for the compaction of various materials. Key technical data (type 37-850) Dedez I Tktjpfx Adhscn • Die diameter: 850 mm • Roller diameter / width: 350 mm / up to 130 mm • Number of roller rolls: 4 pieces • Roller speed: approx. 2.5 m/s • Drive motor power: 132 (at 1500 min⁻¹)

Condition: like new (used), Year of construction: 2022, functionality: fully functional, total length: 9,500 mm, total width: 1,000 mm, overall weight: 3,000 kg, Silo discharge screw conveyor for dried or wet sawdust. The system is in new condition and comes in its original packaging. Dcsdpfxjz Ix Iqe Adhjn The photo is a sample image – the system has never been installed. Discharge screw conveyor for silo internal diameter of 8.9 m. Discharge rate: 40 m³ per hour. Drive power: 15 kW. Lower section: for accommodating the screw conveyor drive, feed drive, main shaft with metering device, and bearings, discharge chute, and blockage sensor. Upper section: with screw shaft, cross-roller swivel joint, and cover hood. Electrical control system is not included!

Condition: excellent (used), Year of construction: 2022, operating hours: 1,000 h, functionality: fully functional, machine/vehicle number: SN210551, overall weight: 14,000 kg, type of input current: AC, input voltage: 400 V, power: 400 kW (543.85 HP), Equipment: type plate available, A MIXACO heating/cooling mixer is a combined system consisting of a heating mixer and a downstream cooling mixer, specifically designed for the processing of powders, granules, and compounds (e.g., PVC dry blends, WPC, or masterbatches). Technical specifications – summary (details can be found in the documents): Hot mixer: • Volume: 3500 liters – Usable volume: 2500 liters • Tip speed: 5-50 m/s • Made of duplex steel – 1.4462 stainless steel • Power drive with 400 kW FC controlled • Vacuum up to 150 mbar abs. Cold mixer: • Volume: 9000 liters – Usable volume: 7650 liters • Tip speed: 3.5 – 7 m/s • Made of 1.4541 stainless steel • Power drive with 90 kW FC controlled The operating principle is divided into two physically and apparatus-wise separate process phases: 1. The heating mixer phase (heating and homogenizing) • Mechanical friction: In the heating mixer, a modular mixing tool rotates at a high circumferential speed (approx. 10–40 m/s). The intense flow and vortex formation (mixing vortex) causes the particles of the mixture to rub intensely against each other. • Heating: This mechanical friction generates the necessary thermal energy directly in the product, quickly and evenly heating the material to the desired target temperature (sometimes exceeding 100 °C). • Recipe component addition: At the same time, all recipe components, such as additives, dyes, or liquids, are perfectly homogeneously distributed. An integrated aspiration system also ensures the dehumidification of the mixture. 2. The transfer • Once the target temperature defined in the process program is reached, a contoured, dead-space-free outlet opens on the heating mixer. • The hot, homogeneous mixture is transferred with minimal residue and quickly to the cooling mixer, which is located directly below or next to it. The heating mixer is then immediately available for the next batch. 3. The cooling mixer phase (gentle cooling) • Heat exchange: In the cooling mixer (available in vertical or horizontal design), the hot material is passed over cooled surfaces. • Water cooling: A targeted cooling water circuit in the double jacket (bottom and side walls) efficiently removes thermal energy from the dry blend. • Agglomeration prevention: A slow, material-friendly stirring mechanism keeps the mixture in motion until the final storage temperature is reached. This prevents caking (compaction) due to residual heat before the material is transferred to silos or further processing. Summary created with AI. The units can be inspected in operation in the Netherlands. Dcodpfx Adez Iww Rjhjn The system for sale was used in the R&D center of UBQ for development purposes. This explains the very good condition for the low number of production hours. We also have a steel structure available for the setup. This is not included in the price. If there is interest, it can be negotiated separately. Currently, the system is located outside of Europe – we need to determine whether direct transport is feasible or whether import to Europe by UBQ is more sensible (which would allow for a sale within Europe with a reverse-charge mechanism).

Year of construction: 2022, condition: like new (used), functionality: fully functional, machine/vehicle number: WDW-70056, WDW – Calibrated containers – Continuous weighing scale for weighing wood pellets or other pellet-shaped bulk goods, complete with a discharge unit. Performance / throughput: 15.6 tons/hour; weighing accuracy: +/- 0.01 kg; cycle times: approximately 2 weighings per minute; the photo shows a representative image; the machine is delivered in its original packaging. Dcsdpfxsz Ixc Ie Adhen

Condition: new, Year of construction: 2022, functionality: fully functional, type of input current: three-phase, power: 50 kW (67.98 HP), input voltage: 400 V, fuel: domestic gas H, overall weight: 2,200 kg, nominal power: 50 kW (67.98 HP), input frequency: 50 Hz, continuous power: 50 kW (67.98 HP), input current: 72 A, Equipment: documentation/manual, For sale: new and unused 2G g box 50plus combined heat and power (CHP) unit from 2022. This is a 2G Energietechnik g box 50plus, configuration as70 4, suitable for simultaneous generation of electricity and heat using natural gas. The unit has never been put into operation and is in new condition. At full load, the CHP unit delivers 50 kW of electrical power and approximately 104 kW of thermal power. The unit is designed for 400 V and 50 Hz and is equipped with a Liebherr G924 natural gas engine and a Leroy Somer LSAH 44.3 generator. Technical specifications: • Manufacturer: 2G Energietechnik GmbH • Type: g box 50plus • Configuration: as70 4 • ID number: H1214 • Year of manufacture: 2022 • Electrical power: 50 kW • Thermal power: approximately 104 kW • Rated voltage: 400 V • Rated frequency: 50 Hz • Rated current: 72 A • Weight of CHP module: approximately 2,200 kg • Fuel: natural gas • Electrical efficiency: approximately 34.5 percent • Thermal efficiency: approximately 71.8 percent • NOx emissions: less than 125 mg per Nm³ • Sound pressure level of CHP: approximately 55 dB(A) at 1 meter Dcodjz Hngmopfx Adhsn The offered package consists not only of the CHP module. The installation also includes two Viessmann boiler bodies, one Viessmann Proflame VM IV 3 gas burner, a separate control cabinet, and various flue gas components, fittings, and related documentation. The original new price of the complete installation was approximately €189,000. The installation comes from a project for which it was ultimately not used. The various main components are from 2022 and have been stored without being put into operation. Due to the size and composition of the installation, we advise interested parties to contact us in advance for further technical information, photos, documentation, and an overview of the components available. An inspection is, of course, possible (location: Winterswijk, Netherlands). Loading onto the buyer's transport vehicle is possible on site.

Year of construction: 2017, condition: excellent (used), Pipe cutting system with optical laser marking detection The FZH Vario Flex is a fully automated pipe cutting system. It is specifically designed for the precise and reliable cutting of stainless steel pipes (e.g., for fuel, brake, air conditioning, or hydraulic lines). The system features optical laser marking detection. The control panel allows you to choose whether the cut is triggered mechanically (e.g., on the back of a union nut) or fully automatically via the optical detection of a laser marking applied to the pipe. Thanks to the integrated rotating 3-jaw cutting head and a micro-spraying unit (minimum quantity lubrication), the processing is extremely tool-friendly. The pipes remain almost completely dry and free of coarse contamination. The entire process, from loading to clamping, cutting, and unloading, is highly automated and carried out in a material-saving cycle. Fully integrated labeling & traceability system: The system is designed for modern quality standards (Industry 4.0 / Automotive). After the cutting process, the barcode label is automatically generated, assigned, and printed for complete part traceability (traceability & system logging directly integrated). Due to two separate box output stations (rear sluices with sliding doors), the system automatically switches to the second station when a box is full. The removal of the finished KLT boxes takes place in parallel with the main operating time without machine downtime. Advantages of the Vario cutting head series compared to conventional cutting methods Shortest changeover times in non-cutting separation Material-saving and free of contaminants Chip-free Easy to maintain No cooling and lubricating agents required Short processing times Cuts all common materials Can be combined with common pipe magazines or from a coil Special designs are possible Dcjdezw Ukcopfx Adhsn Technical data & capacities Maximum pipe length (feed): 1,000 mm Material specification: Optimized for stainless steel pipes (also with pre-assembled union nuts or crimped ends) Sensors & positioning: Optical sensors for the automatic detection of laser markings on the workpiece Feed system: Automatic drum magazine / vertical disc feed (for manual or automatic loading) Length adjustment: Manually adjustable to different pipe lengths using a mechanical handwheel Cutting method: Chip-removing sawing / Rotating cutting head with three-jaw clamping and cutting mechanism (up to 600 rpm) Coolant system: Integrated micro-spraying unit (MMS) for minimum quantity lubrication Control: Siemens SIMATIC HMI industrial PC with TFT monitor, keyboard and mouse Setup operation: Mobile Siemens Teach-In terminal for manual axis configuration and position storage Integrated labeling and barcode printing system Enclosure: Aluminum profile system with safety polycarbonate windows Logistics / output Integrated box placement station 2 separate box output stations for rear removal via protected sluice systems with sliding doors Suitable for standardized KLT containers (600x400 mm and 400x300 mm) Manufacturer: FZH Engineering GmbH Type / Platform: Vario Flex Year of manufacture: 2017 Material: Stainless steel Cutting head: Vario flex Special features: Pipes with union nuts Diameter Ø 6-76 mm Output length L = 150-1,000 mm Separation based on laser marking Wall thicknesses: 1 to 1.3 mm Condition: The system is in excellent optical and mechanical condition.

Condition: like new (used), Year of construction: 2016, operating hours: 500 h, functionality: fully functional, spindle speed (max.): 24,000 rpm, Gravograph IS 6000 IQ – CNC engraving machine – approx. 500 operating hours For sale is a very well-maintained Gravograph IS 6000 IQ with only approx. 500 operating hours. The machine is suitable for engraving and milling operations, for example, for the production of signs, lettering, and custom engravings. Dodpsz D Htgjfx Adhocn Machine data: Manufacturer: Gravograph / Gravotech Model: IS 6000 IQ Year of manufacture: 05/2016 Operating hours: approx. 500 Condition: used, very well maintained Equipment: Engraving software GS8-GRAPHIC incl. dongle Sturdy machine table with T-slots for workpiece clamping Matching base frame Wired hand control unit Extraction system on the machining head Spraying device 750 W high-frequency spindle kit for the IQ series according to the order confirmation from November 2017 The machine was purchased in December 2016. Its excellent condition and low usage with only approx. 500 operating hours are particularly noteworthy. Price: net 12,500 EUR Location: 09627 Bobritzsch-Hilbersdorf Availability: immediately If you are interested, we look forward to receiving your inquiry.

Year of construction: 2019, operating hours: 3,000 h, condition: excellent (used), functionality: fully functional, machine/vehicle number: 10031325, This is a high-resolution NIR system capable of detecting particles in the 3 mm size range. Additionally, the machine is equipped with an electromagnetic detector that has a sensitivity of approximately 1.5 to 1 mm, depending on the metal type. Depending on the settings, it can sort positively or negatively. Technical data: Dcsdpfjzl Uzwjx Adhen Belt width: 1024 mm Nozzle bar: 6.4 mm working width Upon request, complete documentation can be provided. The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price does not include packaging on a pallet.

Condition: used, Year of construction: 2000, machine/vehicle number: 000909 / 2000, functionality: fully functional, power: 15 kW (20.39 HP), volume flow: 10,500 m³/h, filter area: 61.5 m², overall weight: 1,950 kg, For sale is a complete, stationary AL-KO PROFI-JET BG 2 dust extraction and filtration system for wood dust, manufactured in 2000. The system was used in a wood processing production facility and is fully equipped with a fan, automatic filter cleaning, rotary valve airlock, silencer, frequency inverter, control cabinet/controller, and extensive ductwork. The dust extraction system was operated inside the production hall, and the cleaned return air was fed back into the production area. The filter system is labeled with H1 and, according to the label, is suitable for separating wood dust with a residual dust content of ≤ 0.2 mg/m³. Technical data of the filter system: Manufacturer: AL-KO THERM GmbH Type: PROFI-JET BG 2 Year of manufacture: 2000 Serial No.: 000909 Airflow rate: 10,500 m³/h Filter area: 62.5 m² Weight of the filter system: approx. 1,600 kg Filtration: surface filtration Filter cleaning: automatic compressed air cleaning Compressed air connection: max. 6.0 bar Filter elements: approx. Ø 120 mm × 2,500 mm length Height of filter unit: approx. 2,600 mm H1 wood dust rating: residual dust content ≤ 0.2 mg/m³ Dimensions: Length: approx. 2,400 mm Width: approx. 1,620 mm Overall height: approx. 4,500 mm Fan: Manufacturer: JKF Industri Type: JK-40 MTD L Power: 15 kW Speed: approx. 2,900 rpm Fan year of manufacture: 2000 The installed 15 kW drive motor is separately rated with 2,920 rpm at 50 Hz and protection class IP55. Frequency control and controller: The dust extraction system is equipped with a Danfoss VLT 6000 HVAC frequency inverter. Complete control cabinet with Siemens controller and Siemens TD 200 operating panel included. The automatic filter cleaning is carried out pneumatically via individually controlled valves. Rotary valve airlock: Manufacturer: AL-KO Type: ZRS 960 Rotary valve: Ø 320 mm Number of blades: 7 Inlet: 250 × 960 mm Outlet: 208 × 960 mm Capacity: 47,450 l/h Motor power: 0.55 kW Speed: 12 rpm Protection class: IP54 Additional equipment: The system includes: - Silencer, connection Ø 400 mm - Return air duct to the production hall - Complete system control - Danfoss frequency inverter - Automatic pneumatic filter cleaning - Rotary valve airlock - Extensive galvanized dust extraction and return air ductwork Dcedpfxez Ikzpj Adhon Large parts of the existing pipelines can be taken over after consultation. The system is still in its assembled condition. This allows the installation, duct routing and existing components to be inspected and documented before purchase. Location / Sale: Location: 3608 Thun, Switzerland Available: immediately Removal by: July 31, 2027 at the latest The system is sold in its current assembled condition. Dismantling, removal, loading and transport are entirely the responsibility of the buyer and at their own expense. If sold abroad, transport, export/import and customs duties will also be borne by the buyer. Inspection possible by appointment. Sale as is, without warranty. Selling price: 15,500.00 EUR Price net, any applicable taxes and duties. Export, customs clearance and import duties are the responsibility of the buyer.

Year of construction: 2013, operating hours: 7,700 h, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 12090, This is a recycling extruder with side feeding for materials (flakes, pellets, etc.). The system is supplied with a control cabinet and a double vacuum system. The pelletizing system is missing at the end of the screw – it is not included in the scope of supply. The cylinder ends at the flange. The extruder is supplied without a screw. The frequency inverter for the main motor was replaced with a new unit 3 years ago. Installed power approx.: 474 kW Cooling water requirement approx.: 190 l/min Fresh water consumption approx.: 110 l/h Feeding system: • Diameter of the feeding screw: 200 mm • Drive for the feeding screw: 45 kW, frequency-controlled • Hopper capacity net 7 m³/250 ft³, • Gear motor 3 × 3 kW • 2 sight glasses in the hopper • 2 level indicators Extruder: • Diameter of the extruder screw: 145 mm • L/D ratio: 24 • Heating power: 50 kW • Extruder drive unit 280 kW Vacuum 1: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 11 kW • Vacuum capacity: 225 m³/h • Vacuum pressure: 33 mbar Vacuum 2: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 7.5 kW • Vacuum capacity: 190 m³/h • Vacuum pressure: 33 mbar Cylinder: • Cylinder: Bimetal extruder cylinder, • Reinforcement layer 1.8–2.0 mm thick, • Hardness 63–65 HRC Dsdpfx Aeznz Ezodhscn Installation conditions: • Voltage: 3 × 400 Volts • Permissible fluctuation max.: +5 % – 5 % • Frequency: 50 Hz Permissible fluctuation max.: +4 % – 4 % • Protective measure: Multiple grounding • Ambient temperature: min. 15 °C, max. 35 °C • Humidity max.: 90 % • Altitude of the installation site: 0 – 1000 m The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center is being closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price is without packaging.

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 24-042, overall weight: 200 kg, type of input current: AC, input voltage: 230 V, belt width: 400 mm, Magnet with neodymium head roller (can also separate slightly magnetized stainless steel parts), small conveyor belt (drum motor), and feed chute. Dodpjz Ihbgsfx Adhocn The conveyor belt and feed chute are adjustable. The machine is mobile on rollers, available immediately, and the price may be negotiable.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 531 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity Djdpfx Asz Agv Uedhjcn - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 532 MAP40, General Data: Dedez Agw Espfx Adhscn - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 533 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. Dcedpfjz Ag Rrox Adhsn - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 530 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm Dedpfx Aszz Rpcedhscn - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2013, operating hours: 3,500 h, condition: used, functionality: fully functional, machine/vehicle number: 12400, TSM/tsi oscillating sieve machines are used for the classification, screening, and dust removal of bulk materials from almost all industrial sectors, such as stones and soils, chemicals, mining, pharmaceuticals, feed, and food. The machine for sale has a diameter of 1200 mm and is equipped with 3 sieve decks with mesh sizes of 3 mm, 1.4 mm, and 0.463 mm. In addition, spare sieves with the following dimensions are included: • 16 mm x 1 piece • 15 mm x 1 piece Dodpfxozmzbme Adhecn • 0.5 mm x 1 piece • 0.16 mm x 1 piece • 0.9 mm x 1 piece • 0.86 mm x 1 piece The drive has a power of 1.5 kW, 400 VAC, 50 Hz, 1450 RPM. The machine was in operation at an R&D center in Israel. As the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price does not include packaging on a pallet.

Condition: new, functionality: fully functional, Year of construction: 2024, screw conveyor diameter: 20 mm, screw conveyor length: 25 mm, noris- Extruder MINI ESE 20/25 D Technical data Screw diameter [mm] 20 Screw length [L/D] 25 Screw speed [min-1] 20-200 min -1 Screw axial pressure [bar] 300 Continuous load 350 maximum Drive Three-phase drive with frequency converter Drive power [kW] max. 2.5 Dcjdpfehx Elfsx Adhon Reduction gear with integrated axial bearing Weight [kg] approx. 160 Dimensions [Lx Wx H] [mm] approx. 1050 x 600x 1590 *) Electrical connection values 3 / N / PE Supply voltage [V] 400 at 50 Hz Control voltage [V] 230 Temperature control electrical resistance heating bands in mica design. Max. processing temperature [°C] 300 Switch cabinet and control panel The electrical installation of the extruder is located in the machine base. The base contains all the necessary switching, control and display devices. The feed zone is water-cooled, the water connection is provided by the customer, a cooling unit for cooling the water is not included in the offer. Extruder tools are not part of the offer

Year of construction: 2021, condition: like new (used), functionality: fully functional, Component 1: ATM-800 P Tangential Dereeler (2 pieces) Heavy-duty dereeler for controlled unwinding of copper wire coils. • Max. coil diameter: 800 mm • Max. coil width: 300 mm • Pickup hole: Ø52 / Ø56 mm Dodpfxez Ap R Io Adhjcn • Max. coil weight: 300 kg • Braking force: 100 - 2000 N • Brake torque: 3 - 800 Nm • Max. speed: approx. 5 rpm • PLC control with torque sensor Component 2: HBK-40-S Automatic Taping Machine Professional automatic taping machine for coil and conductor insulation. • Servo-controlled taping head • Operator terminal and display • Integrated X-axis guidance • Electric hysteresis brake • Automatic overlap control via encoder • Suitable for various insulation materials

Condition: excellent (used), functionality: fully functional, REF: MM5465 1 x Seitz-Werke GmbH filling machine for bottles. Fed by counter-pressure tank. Dsdpfxox A A I Hs Adhecn Manufacturer - Seitz-Werke GmbH Model - SF 12. Date of manufacture - 1961 (has been refurbished since). Speed - up to 1200 bph (depending on filling volume). Capacity - variable filling range (whatever bottle size fits into holders). Overall dimensions - 1100mm diameter x 2350mm H. Last used in March 2023.

Condition: used, Year of construction: 2024, machine/vehicle number: 211-11-01-23-02, total width: 1,070 mm, total length: 2,470 mm, total height: 1,850 mm, This E-bike motor test bench, type G4, manufactured in 2024 by EMEC Prototyping GmbH, will be auctioned off in our online auction "Closure of a well-known German manufacturer of e-bike drives: warehouse, production, and office equipment, test stations, bicycles, tools, accessories." Further details: E-bike motor test bench EMEC G4, manufactured in 2024 Test bench for e-bike drives with two test levels in an aluminum profile enclosure with safety doors, including a mounted control cabinet and temperature control unit. According to the nameplate: Manufacturer: EMEC Prototyping GmbH Type: Motor test bench G4 Year of manufacture: 2024 Electrical power: max. 16.6 kW Connection power: 3Ph~ 400 V / 32 A Dimensions (L x W x H): 2470 x 1070 x 1850 mm Weight: 1200 kg, permissible total weight: 1350 kg As far as can be seen (information without guarantee): Both test levels appear to be constructed identically, per level: Beckhoff servo motor AM8064-0R1A-0000 (11.5 kW, 49.7 Nm, 3000 rpm) with gearbox and Beckhoff air cooling kit Second servo motor with gearbox and fan unit, design presumably Beckhoff AM8053 (nameplate not visible) Dedpfxez Ngzcs Adhjcn 2 torque measuring shafts Test specimen mounting with ring holder on a carriage Linear guides with clamping levers for axial adjustment Heat exchanger behind the test specimen mounting Fan for test specimen cooling Connections for CAN, service, and auxiliary voltage (AUX) Additionally: Julabo 1200F refrigeration circulator with touch control unit Laboratory power supply EA-PS 9080-100 Control cabinet (as far as can be seen): Emergency stop, main switch, on/off button, front connections USB and RJ45, control cabinet fan Rollers and adjustable feet All information without guarantee. The technical specifications were determined based on nameplates and visual inspection. The actual condition, as inspected, is decisive. Functionality not tested.

Condition: used, Year of construction: 2013, functionality: fully functional, machine/vehicle number: NS-009-0000-300, type of input current: AC, nominal power at 50% duty cycle: 250 kVA, throat depth: 300 mm, short-circuit current: 50,000 A, input voltage: 400 V, type of cooling: water, total width: 1,000 mm, total length: 1,000 mm, total height: 1,850 mm, overall weight: 1,000 kg, open-circuit voltage: 22 V, Zens Multifunction Resistance Welding Machine 250 kVA MF – 23 kN – 50 kA – Year of Manufacture 2013 For sale is a high-quality Zens multifunction resistance welding machine in a robust industrial design. The system was developed for demanding resistance welding processes and is ideally suited for series production in the automotive, supplier, electrical, and metal industries. The machine operates with modern medium frequency (MF) technology and achieves a welding power of 250 kVA at a 50% duty cycle. The powerful SER medium frequency inverter (700 A) enables a maximum welding current of 50 kA and ensures maximum process stability as well as reproducible welding results. With a maximum welding force of 23 kN and an overhang of 300 mm, the system is suitable for a wide range of resistance welding applications. Technical Data Manufacturer: Zens Machine Type: Multifunction Resistance Welding Machine Year of Manufacture: 2013 Welding Power: 250 kVA (Medium Frequency / MF) at 50% duty cycle Max. Welding Current: 50 kA SER Medium Frequency Inverter: 700 A Welding Control: SER-Mega1 Maximum Welding Force: 23 kN Overhang: 300 mm Equipment CE-compliant protective enclosure CE safety light curtain Welding table for welding forces up to 23 kN Pressure compensation tool Dcedpfx Aezqucfjdhen QSF-M quality assurance system Position measuring system for process monitoring PLC control (Siemens S7) Robust industrial design for continuous industrial operation The combination of powerful medium frequency technology, precise force and position control, and modern PLC and SER welding control ensures high process reliability and consistently reproducible welding results. Thanks to the complete CE safety equipment, the machine can be easily integrated into existing production lines. The system is in good condition and can be inspected and demonstrated at any time by prior appointment.

Condition: used, Year of construction: 2021, functionality: fully functional, machine/vehicle number: 1605269/1, total width: 630 mm, total height: 1,115 mm, total length: 1,010 mm, working width: 460 mm, input voltage: 400 V, type of input current: AC, overall weight: 200 kg, power: 0.37 kW (0.50 HP), roller diameter: 100 mm, passage height: 80 mm, feed rate X-axis: 35 m/min, height adjustment type: mechanical, tank capacity: 2 l, roll width: 450 mm, input frequency: 50 Hz, workpiece height (max.): 80 mm, Equipment: double-sided, For sale is a well-maintained glue and roller application machine from Axel Wirth Maschinen GmbH, type LW 100/450. The machine was manufactured in 2021, has comparatively few operating hours, and is in technically perfect and well-maintained condition. A particular advantage is the adjustable working speed or feed rate (6 - 35 m/min). This allows the machine to be flexibly adapted to different workpieces, materials, and application media. The machine is mounted on a sturdy, mobile base with lockable wheels. As a result, it can be easily moved within the production area and safely positioned at the respective location. A total of two identical machines are available. The stated price applies per machine. An attractive package price is possible if both machines are purchased. The LW 100/450 is suitable for the uniform application of liquid and pasty media onto flat or textured workpieces, for example: - Glue and adhesive - Oil and wax - Stain and primer - Paints and dispersions - Resins and comparable application media Among other materials, wood, solid wood, parquet flooring, chipboard, cork, cardboard, metal, stone, rubber, and insulation materials can be processed. The application quantity can be adjusted via the lateral adjustment devices. The rollers and glue trays can be removed with a few simple steps, making the machine easy to clean. Technical data and equipment Dcjdpfxszr H Aas Adhen Manufacturer: Axel Wirth Maschinen GmbH Type: LW 100/450 Year of manufacture: 2021 Nominal width: 450 mm Working width: approx. 460 mm Passage height: approx. 80 mm Diameter of the application rollers: 100 mm Capacity per glue container: approx. 2.3 liters Drive power: 0.37 kW Adjustable working speed or feed rate Application rollers above and below Separate control cabinet Main switch and emergency stop Mobile base with lockable wheels CE marking Condition: used, well-maintained, and technically perfect Operating hours: comparatively low Inspection and test run are possible after prior appointment. Collection at the Leun location. Shipping by freight forwarder can be organized if required, upon agreement. If you have any questions or are interested, please do not hesitate to contact us. We will be happy to provide further information and photos. Price: €5,900 (negotiable) per machine plus VAT (can be shown). Package price for both machines: on request All information is provided to the best of our knowledge. The sale takes place under the conditions applicable to the seller for used machines.

Condition: used, Year of construction: 2016, Offered is a pad printing machine with protective enclosure. Equipped with plate holder, printing pads and remaining inks, where available. Operating usage: approx. 4000 cycles/year. Weight: approx. 400kg. Overall dimensions X/Y/Z: approx. 1300mm/1000mm/1790mm. Inspection possible by arrangement. Dcsdpfx Aoz Irl Njdhon