Used Fliegl Zhka 330 - 30 M³ for sale (80,697)

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,350 kg, maximum load weight: 28,650 kg, overall weight: 33,000 kg, axle configuration: 2 axles, loading space length: 7,200 mm, loading space width: 2,420 mm, loading space height: 1,750 mm, loading space volume: 30 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,400 mm, suspension: air, tire size: 385/65R22,5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements. Further information Chassis, semi-trailer, tipper Fine-grained steel welded construction, lightweight design, fifth wheel with 2 interchangeable kingpins Curved front panel, patented 24 tons, 2-speed landing gear, single-sided operation, with straight lower part, without slide-out compensation 2 support wedges with holder Underrun protection, foldable Half-shell fenders Tarp pole with bracket Dodpfx Aei Rizija Ijku 2 towing hooks at the rear Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-aligned, reducing tire wear and fuel consumption Axles in off-road design Air suspension 1st axle, automatic lift axle, including forced lowering and starting assist Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Brake system 2-line compressed air brake system, colored line routing for easy servicing Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic brake system with EBS socket at the front, without connecting cable Note: The trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS! with lifting and lowering valve Vehicle - driving stability system Wheels and tires 385/65 R22.5, manufacturer's choice Steel rims, factory silver "TPMS" tire pressure monitoring system according to ECE R 141, display via the towing vehicle's display, via EBS, without installation in the truck (this must be available in the truck. Only on the base tires). Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the side Yellow LED lighting on the side linked to the turn signal "flashing side marker lights" 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole non-interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chrome plated, with HDK screw connection, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck auxiliary drive Tippers Aluminum box tipper made of high-quality, abrasion-resistant material, front wall 5 mm thick, with external side walls made of 30 mm hollow chamber profiles, cleanly welded, with a top profile that prevents bulk materials from shifting. Inside with a ladder on the front wall (not in connection with Cramaro). Shovel and broom holder on the outside of the front wall. Greenline - conical and aerodynamic tipper body shape Diaphragm - rear wall Rear wall as a swing gate with double hinge, externally mounted with double hook locking. Rear wall with rubber seal. Note! Heat-resistant up to max. 170°C! Floor continuously 6 mm thick Standing platform with ladder, connection plate for air/electricity and brake with large clearance for best possible operation. Roll-up cover on one side to be placed on the right, with central locking on the left Country of registration/Signs Germany with Dekra approval and certificate (according to §13 EC - FGV) 24/7 service hotline prepared for single-row license plate holder Contour marking with reflective strips according to ECE R 048, white on the side and red at the rear Paintwork Frame DB 7350 Novagrau "10-year warranty against rust-through" Tipper body RAL optional, solid color Roll-up cover RAL 7035 light g

Condition: used, first registration: 09/2016, color: other, Year of construction: 2016, Equipment: ABS, = Additional options and accessories = - BPW-Assen - Drum brakes - Lift Axle = Remarks = Fliegl, 2016, BPW axles, Dksdpfx Aaoz Eh N Ee Isu Axle 1 Liftable, Drum brakes = Dealer information = Bank data: Rabobank Account: 39.33.10.655 IBAN: NL73RABO0393310655 Swift code: RABONL2U - Always check our bank details before transaction! - Reservation of vehicles is not possible without a deposit. - Writing and text errors are reserved for all vehicles offered.

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, total height: 34 mm, total length: 230 mm, total width: 2,400 mm, saw band length: 4,700 mm, saw band width: 1 mm, Selling a MEBAMAT 330 12,500 operating hours The machine has cut 99% of plastic. You can find the machine's technical specifications at MEBA. Dkedpewhix Ejfx Aa Iou

Condition: excellent (used), Year of construction: 2013, Engel Victory 330H/80V/160 combi Ecodrive / Production line with the Sepro SR S5-25 S3 Trans robot / Operating hours: approx. 18,000 h in automatic mode Year of construction: 2013 Injection unit: Screw diameter: 30 mm Injection weight: approx. 100 g Injection pressure: 2385 bar Dosing volume: 113 ccm Clamping unit : Clamping force: 160 t Distance between tie bars: 0x0 mm Size of the clamping plates: 750x750 mm Ejector: hydraulic Clamping unit: hydraulic Control: CC 200 - touch screen Additional equipment: 2K injection molding machine with rotary table and robot Tie-bar-less machine, hybrid: energy-saving, high-speed and very quiet Very good technical condition Operating hours: approx. 18,000 h in automatic mode Total number of operating hours: 24,312 h Euromap 67 Robot interface Air valve x 5 Hydraulic core pull x 5 Control unit with hot runners x 16 Reinforced injection units - bimetal Main motors - 2 x servo motor controlled with inverter Proportional valves on injection units - precise spraying Screw diameter in the vertical injection unit: ⌀22 mm - approx. 28 g/hp It is possible to purchase a turntable Robot Sepro SR S5-25 S3 Trans Year of construction: 2013 3-axis robot: 3 axes are driven by servomotors (electric): X, Y, Z (telescopic) Travel distances in axes approx.: X-2000, Y-1000, Z-1500 Automatic axis lubrication Touch control panel The safety package for robots Robot with adapter and protective housing Purchase of the robot for an additional charge Dimensions Weight: 8700 kg Dkedpfx Aoz Ipqvja Iou Length/width/height: 5.35x1.76x3.42 m All offered machines are started by our service technicians before sale. It is possible to obtain a video of technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2017, Engel Victory 330H/200V/140 combi Ecodrive / Production line with the Sepro Multi Inject 20 robot / Operating hours: approx. 18,000 h in automatic mode Year of construction: 2017 Injection unit: Screw diameter: 30 mm Injection weight: approx. 100 g Injection pressure: 2400 bar Dosing volume: 113 ccm Clamping unit: Clamping force: 140 t Distance between tie bars: 0x0 mm Size of the clamping platens: 750x750 mm Ejector: hydraulic Clamping unit: hydraulic Control: CC 300 - touch screen Additional equipment: 2K injection molding machine with rotary table and robot Tie-bar-less machine, hybrid: energy-saving, high-speed and very quiet Very good technical condition Operating hours: approx. 18,000 in automatic mode Total number of operating hours: 25,369 h Euromap 67 Robot interface Air valve x 8 Hydraulic core pull x 5 Control unit with hot runners x 16 Reinforced injection units - bimetal Main motors - 2 x servo motor controlled with inverter Proportional valves on injection units - precise spraying Parallel movements Built-in pressure quality control system from Sensor Kistler - mold pressure measurement Screw diameter in the vertical injection unit: ⌀25 mm - approx. 58 g/hp It is possible to purchase the original Foboha turntable for an additional charge Turntable diameter: 740 mm Sepro Multi Inject 20 robot Year of construction: 2017 3-axis robot: 3 axes are driven by servo motors (electric): X, Y, Z (telescopic) Travel distances in axes approx.: X-4000, Y-1200, Z-1500 Automatic axis lubrication Touch control panel The safety package for robots Robot with adapter and protective housing Purchase of the robot for an additional charge Dkedpsz Ipqpjfx Aa Iju Dimensions Weight: 10300 kg Length/width/height: 5.56x1.76x3.46 m All offered machines are started by our service technicians before sale. It is possible to obtain a video of the technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2016, operating hours: 33,921 h, functionality: fully functional, ENGEL Duo 1350H/330W/600WP combination machine including robot Year of manufacture: 2016 Djdjz Nkavepfx Aa Ijku Operating hours: 33921 h Clamping unit Clamping force: 600 t Opening stroke: 1400 mm Tool mounting height: 450 - 1080 mm Maximum mold parting line distance: 1850 mm Mold size (h x v): 1115 x 975 mm Injection unit Screw diameter: 55 and 35 mm Injection volume: 618 + 154 cm³ Injection weight PS: 590 + 151 g Injection pressure: 2183 + 1600 bar Equipment: - Interface for rotary table/index plates - Core pull system, 2-way fixed mounting plate - Core pull system, 4-way movable mounting plate - Tool heating, 40 control circuits - Microcomputer CC200 Robot Engel Viper 40 RC300 - Max. handling weight: 23 kg - Z-axis: 4280 mm - X-axis: 1200 mm - Y-axis: 1500 mm - C-axis compact drive M - A-axis compact drive M - 8 additional compressed air circuits - 6 additional vacuum circuits

Condition: excellent (used), Year of construction: 2014, machine/vehicle number: 24406, functionality: fully functional, operating hours: 900 h, input voltage: 400 V, input frequency: 50 Hz, ⚙️ IMA BIMA CUT 145/330 – Technical Specifications (Main) 🔹 Working range (axis travel) • X axis: approx. 3300 mm • Y axis: approx. 1450 mm • Number of axes: 3 (typically X, Y, Z) 🔹 Spindle • Spindle power: approx. 18 kW • Applications: milling, drilling, and board nesting 🔹 Tool changer • Automatic tool changer (ATC): up to 18 positions 🔹 Material clamping system • Vacuum table with beams and suction cups 🔹 Saw unit • Saw projection: approx. 145 mm • Cutting length: approx. 330 mm ⸻ 🛠️ Typical features and equipment • 5-sided drilling (top + X+/X−/Y+/Y− sides) Dkjdpfoykn Dwex Aa Ieu • Saw unit for cutting and grooving • Optional horizontal milling aggregate (HBO) • Automatic loading and unloading table (depending on configuration) • Nesting system (panel optimization with simultaneous machining) • Automatic lubrication • Waste and chips conveyor (belt) ⸻ 📌 General information • Manufacturer: IMA Schelling (Germany) • Year of manufacture commonly found in offers: approx. 2010–2016 (often 2014) • Applications: furniture production, MDF panels, HPL, solid wood, nesting

Condition: used, Year of construction: 2000, functionality: fully functional, machine/vehicle number: 1406, total width: 2,500 mm, total length: 2,710 mm, total height: 3,000 mm, overall weight: 10,000 kg, maximum load weight: 330 kg, loading space volume: 3.3 m³, air pressure: 7 bar, Tonello 330 HS Industrial Garment Washing & Dyeing Machine Large-Capacity 3300 L Industrial Garment Wet-Processing Machine with B&R Touchscreen Control The Tonello 330 HS is a large-capacity industrial garment washing and wet-processing machine manufactured by Tonello S.r.l. (Sarcedo, Italy), the leading garment-finishing technology brand. The 330 class (3300 L drum) handles industrial washing, dyeing, softening, bleaching and stone-wash / enzyme effects on denim and garments at production scale. This unit (MASI in-house reference "Pesumasin No 3") was in professional denim-finishing production until factory shutdown. The machine body dates from 2000 and the complete electrical control system was rebuilt in 2014 with a new Tonello / B&R panel. Technical Specifications • Manufacturer: Tonello S.r.l. (Italy) • Model: G1 330 HS • Serial / Matricola: 1407 • Year: machine 2000 / electrical control rebuilt 2014 • Basket / Drum Volume: 3300 L • Power Supply: 380–400 V, 3-phase + GND, 50 Hz • Installed Power: 27 kW (machine plate) / 14 kW (2014 control plate) • Air Pressure: 7 bar · Max Steam Pressure: 3 bar · Hydraulic Pressure: 10 bar • Weight: 10,000 kg • Supply Cable: 25 mm² • Country of Manufacture: Italy Key Features • Large 3300 L stainless drum for high-capacity garment wet processing • B&R Power Panel 300 touchscreen HMI (rebuilt 2014) with programmable cycles • Yaskawa Varispeed 616G5 variable-frequency drum drive • Mettler Toledo weighing controller and Siemens Sitrans flow metering • Automatic chemical dosing system • Steam, water, air and hydraulic services • Front loading door with sight glass Includes • Tonello 330 HS washing machine with stainless drum • B&R touchscreen control cabinet and pushbutton console • Yaskawa VFD and PLC electrical cabinet • Chemical dosing system, pumps and instrumentation Applications • Industrial denim and garment washing • Garment dyeing and over-dyeing • Softening, bleaching, enzyme and stone-wash effects • High-volume garment wet processing Condition • Working — main machine functional (per factory records) • Video recorded 19.3.2026 • Previously in professional denim-finishing production (MASI "Pesumasin No 2") • Machine from 2000 with 2014 electrical-control rebuild • Typical wear/dust from a wet-processing environment • Available for inspection under working conditions before dismantling Location Valga, Estonia Dsdpjzmvgwefx Aa Ioku Dismantling & Transport Buyer responsible for dismantling, loading, transportation. Sales Terms Sold as-is, where-is, without warranty. Part of the MASI Jeans factory liquidation. Part of the Tonello industrial laundry line (available individually or as a complete line).

Condition: used, Year of construction: 2000, functionality: fully functional, machine/vehicle number: 1407, total width: 2,500 mm, total length: 2,710 mm, total height: 3,000 mm, overall weight: 10,000 kg, maximum load weight: 330 kg, loading space volume: 3.3 m³, air pressure: 7 bar, Tonello 330 HS Industrial Garment Washing & Dyeing Machine (re-controlled 2014) Large-Capacity 3300 L Industrial Garment Wet-Processing Machine with B&R Touchscreen Control The Tonello 330 HS is a large-capacity industrial garment washing and wet-processing machine manufactured by Tonello S.r.l. (Sarcedo, Italy), the leading garment-finishing technology brand. The 330 class (3300 L drum) handles industrial washing, dyeing, softening, bleaching and stone-wash / enzyme effects on denim and garments at production scale. This unit (MASI in-house reference "Pesumasin No 3") was in professional denim-finishing production until factory shutdown. The machine body dates from 2000 and the complete electrical control system was rebuilt in 2014 with a new Tonello / B&R panel. Technical Specifications • Manufacturer: Tonello S.r.l. (Italy) • Model: G1 330 HS • Serial / Matricola: 1407 • Year: machine 2000 / electrical control rebuilt 2014 Dodpfx Ajzmt S Dsa Isku • Basket / Drum Volume: 3300 L • Power Supply: 380–400 V, 3-phase + GND, 50 Hz • Installed Power: 27 kW (machine plate) / 14 kW (2014 control plate) • Air Pressure: 7 bar · Max Steam Pressure: 3 bar · Hydraulic Pressure: 10 bar • Weight: 10,000 kg • Supply Cable: 25 mm² • Country of Manufacture: Italy Key Features • Large 3300 L stainless drum for high-capacity garment wet processing • B&R Power Panel 300 touchscreen HMI (rebuilt 2014) with programmable cycles • Yaskawa Varispeed 616G5 variable-frequency drum drive • Mettler Toledo weighing controller and Siemens Sitrans flow metering • Automatic chemical dosing system • Steam, water, air and hydraulic services • Front loading door with sight glass Includes • Tonello 330 HS washing machine with stainless drum • B&R touchscreen control cabinet and pushbutton console • Yaskawa VFD and PLC electrical cabinet • Chemical dosing system, pumps and instrumentation Applications • Industrial denim and garment washing • Garment dyeing and over-dyeing • Softening, bleaching, enzyme and stone-wash effects • High-volume garment wet processing Condition • Working — main machine functional (per factory records) • Previously in professional denim-finishing production (MASI "Pesumasin No 3") • Machine from 2000 with 2014 electrical-control rebuild • Typical wear/dust from a wet-processing environment • Available for inspection under working conditions before dismantling Location Valga, Estonia Dismantling & Transport Buyer responsible for dismantling, loading, transportation, and all related costs. Professional rigging required (heavy industrial machine, ~10 t). Sales Terms Sold as-is, where-is, without warranty. Part of the MASI Jeans factory liquidation. Part of the Tonello industrial laundry line (available individually or as a complete line).

Condition: excellent (used), Year of construction: 2011, operating hours: 80,000 h, functionality: fully functional, clamping force: 1,200 kN, screw diameter: 40 mm, displacement volume: 201 cm³, total length: 5,245 mm, total width: 1,525 mm, total height: 2,300 mm, overall weight: 7,200 kg, input frequency: 50 Hz, input voltage: 400 V, The machine comes from the current series production of a plastics processor and, according to the previous owner, is fully functional. An inspection at the production facility is possible after scheduling an appointment. Key data (according to manufacturer's specifications ENGEL) • Clamping force 1,200 kN (120 t), tie-barless clamping unit • Platen dimensions 790 × 790 mm (Wide Platen), minimum tool size 350 × 350 mm • Tool installation height min. 400 mm, opening stroke 506 mm, max. platen distance 900 mm • Ejector 130 mm stroke, 39.8 kN • Injection unit 1 (330H, horizontal): screw Ø 40 mm, displacement volume 201 cm³, specific injection pressure 1,221 bar / increased 1,667 bar • Injection unit 2 (80W, angled position): displacement volume 38 cm³ (screw Ø 22 mm) or 49 cm³ (Ø 25 mm) [CHECK 09/25: which screw] • Hydraulics: pump drive 30 kW, oil capacity 300 l • Connection 3 × 400 V, 50 Hz, 139 kW / 220 A • Control system ENGEL CC 200 [CHECK 09/25] Dedpfx Aasz Eimfo Ijku • Operating hours 87,300 h (as of 09/2026); plasticizing cylinder Ø 40 mm from 2021 with 20,300 h (according to the previous owner) Your advantages • Tie-barless: The tool space is free from tie bars. Large and bulky tools with core pulls can be accommodated, for which a larger clamping force class would often be required in tie-bar machines. • Short setup times: Tools are installed from the side without tie-bar removal. • Automation: Robots travel horizontally into the tool space – smaller cell, lower hall height, shorter cycles. • Tool-friendly: Platen parallelism via the patented ENGEL Flex-Link system (according to the manufacturer). • Hydraulic connections for core pulls, parallel movements programmable (according to the previous owner) – for tools with sliders, undercuts and thread cores. • Combi version with space for a rotary table or indexing plate (according to the manufacturer). • Main injection unit with a newer plasticizing cylinder (2021). • Second injection unit, according to the previous owner, was not used in operation, therefore minimal wear. [CHECK 09/25: unit available + free injection test] Typical applications 2K hard/soft and two-color: handles with TPE zone, housings with molded-in seal, switches and operating elements, connectors with seal, rollers with soft tread, closures with sealing lip, cable glands, medical components, two-color design parts. Single-component: technical precision parts and parts with inserts. Scope of supply • Injection molding machine as described [CHECK 09/25: with both injection units] • ENGEL data sheet, layout plan, platen drawing Not included in the scope of supply: the peripherals visible in the photos (removal/automation with protective enclosure, temperature control units, material handling and drying, mobile switch cabinet) and tools. Terms and conditions • Price on request • Available presumably from week 48/2026 • Payment 100% advance payment • Transport throughout Europe on request Note: The technical specifications are based on the manufacturer's documentation and the information provided by the previous owner. They are for informational purposes only and do not constitute an agreement on the condition or a warranty within the meaning of §§ 434, 443 BGB. We will confirm individual values during the inspection or upon request. Offer subject to change, prior sale reserved.

Condition: excellent (used), Year of construction: 1995, functionality: fully functional, Equipment: documentation/manual, CNC-controlled vertical machining center AXA VSC-3-3000-M Year of manufacture: 1995 Control system: Heidenhain TNC 407 Technical data: X-axis travel: 3000 mm Y-axis travel: 420 mm Z-axis travel: 480 mm Table size: approx. 3000 x 500 mm Dedpfey U Hy Tsx Aa Ioku Spindle connection: SK40 Speed range: up to 6000 rpm 22-tool automatic tool changer Coolant system Heavy-duty frame construction Special features: Additional angular/universal milling head 4-/5-axis machining possible Flexible machining of complex workpieces Ideal for toolmaking, mechanical engineering and single-part production The machine is in good condition. Inspection under power is possible by arrangement.

Year of construction: 2010, condition: ready for operation (used), A Thalmann long folding machine with a touchscreen control system renewed in 2025 is available. Working width: 8200mm, usable width: 8000mm, max. sheet thickness: 3mm, max. upper beam opening: 150mm, bending beam width: 12mm, feed rail: 12mm. Documentation available. An on-site inspection is possible. Dkjdsy Tn N Hopfx Aa Iju

Condition: used, maximum load weight: 2,300 kg, overall weight: 3,000 kg, axle configuration: 2 axles, first registration: 06/2015, Ref. No.: B - 06 On behalf of customer Fliegl * TTS 30-30 Dsdsxvf U Nopfx Aa Ieku * Low-bed trailer * Ramps * 2-axle * Permissible total weight 3000kg * Very good condition, little used Trade-in possible Financing starting at 3.99% Errors and prior sale excepted! The information in this advertisement is non-binding descriptions and does not constitute guaranteed characteristics. The seller assumes no liability for typographical or data transmission errors. Stated features should be checked separately. All details in the ads are non-binding! Nationwide delivery within Germany available upon request. Opening hours: Monday to Thursday from 9:00 am to 5:00 pm Friday from 9:00 am to 2:00 pm and by appointment!

Year of construction: 2016, condition: excellent (used), functionality: fully functional, machine/vehicle number: 116245, GM DC330 Digital die cutting machine/ converter Compact footprint Unwind Djdpfx Aajylpvdo Ijku Web guide Web width 330 In / Outfeed nip for tension control Magnetic die station 200z / 25inch to support die plates of 50mm to 520mm Distortion/ Dispro factor to handle other tooth size plates Re Reg mark reader to support the printed web Die-cut offset possible inline Lateral/ Cross movement possible Waste rewinder Slitting station with manual 7 air pressured V-knives Upper and Lower rewind with options of clock or anti clockwise rotation Label or meter counting Core mandrels/spindles of 25mm, 38mm, 44mm and 76mm x 2 Cold foil Self adhesive lamination Laminator unwind and rewind Silencer to reduce noise when using the lamination Full Flexo station Varnish tray, Picking roller, Anilox roller, Print roller included GEW UV lamp Min 6 bar air pressure required Machine Weight 1200Kg !! Available for immediate sale !!

Condition: ready for operation (used), Year of construction: 2002, travel distance X-axis: 2,940 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 950 mm, controller manufacturer: HEIDENHAIN, controller model: iTNC 530, overall weight: 18,000 kg, spindle speed (max.): 12,000 rpm, number of slots in tool magazine: 36, number of axes: 3, This 3-axis AXA VHC-3-3000-M/E was manufactured in 2002. It features an impressive X-axis travel of 2940 mm, Y-axis travel of 900 mm, and Z-axis travel of 950 mm. The machine includes a robust table size of 4350 x 900 mm and a spindle speed range of 40 - 12,000 rpm. If you are looking to get high-quality machining capabilities, consider the AXA VHC-3-3000-M/E vertical machining centre we have for sale. Contact us for further details. Dkjdpfx Asz Iyppja Ieu Table Clamping Surface: 4350 x 900 mm (with 7 T-slots 18H7 RTA integrated)Swivel Head: Stepless positioning swivel headNC Rotary Table: Type RTA 4 L - 800Spindle Speed Range: 40 - 12,000 rpmSpindle Taper / Tool Holder: SK 40 DIN 69871-A (Hohlwellenmotor, water-cooled)Spindle Note: Spindle replaced/renewed a few years ago for nearly €30,000Tool Changer: 36 positions, movable in Y-directionConnected Load: 69 kVAVoltage: 3x400V/230V/N/PE, 50 HzControl Voltage: 24 V DCFuse Protection: max. 125 AAdditional Equipment:External band filter coolant system Type SA 25/600 (30 bar, 400 Liters)Slat conveyor chip conveyor Type FSB 300 (discharge height 1200 mm, left side)Minimum quantity lubricationElectric handwheel HR 4103D Touch Probe Type MP 10 EVisport (Fabrikat Hema)Heat exchanger Type SK3328 (Fabrikat Rittal)2 Hand spray guns Technical Specification Taper Size SK 40

Condition: like new (used), Year of construction: 2023, GM – DC330MINI V4 Label Converter Year of Manufacture: 12/2022 _____ Dksdov Aa Twopfx Aa Isu Machine Specifications and Equipment:  Max Webwidth: 330mm  Speed up to 65 m/min, semi rotary; 72 m/min full rotary  Unwinding max. 700 mm  Rewinding max. 450mm  Touch screen  Flexo Unit Corona  Webedge Control  Semi-rotary die cutting  Automatic register check  GEW – UV  Lamination  GM SmartCrush _____

Year of construction: 2023, condition: as good as new (ex-display), Up-stroke construction pressing force 300 kN pressing surface 300 x 300 mm specific force 3,3 N/mm² opening 200 mm heating platen as solid steel plate Dkodpfokuz T Uex Aa Isu electrical heated up to 300°C (570 °F) control Siemens S7-1200 with 12" Touchpanel mechanical safety door data collection

Condition: excellent (used), Year of construction: 2008, Gravicolor 30 GC 30-M-O-Z Manufacturer: Motan Year of production: 2008 A gravimetric dosing and mixing unit designed for direct mounting on the inlet flange of a plastics processing machine. The device allows dosing and mixing of up to 4 granulated components. The actual, measured and weighed quantities are constantly compared with the set values using a modern microprocessor-based control system, which guarantees very high recipe accuracy (+/- 0.1%) thanks to continuous self-optimization. The complete unit includes: 2 feed tanks for primary material or regranulate/primary material 2 feed tanks for masterbatches or additives 2 pneumatically controlled conical dosing heads 2 precision dosing screws with motor drive Dodpfx Aowm Ii Tsa Isku Material tanks – capacity approx. 7 litres Weighing tank – capacity approx. 0.8 litres Mixing tank – capacity approx. 3.0 litres Manually operated gate valve GRAVInet controller with colour touch panel for recipe, milled material and process data management, vibration compensation and continuous self-optimisation; built-in Ethernet port and standard reporting/printing functions Technical data: Average capacity: 60 kg/h Main component dosing range: 1–100% Additive dosing range: 0.5–10% Power supply: 1/N/PE 230 V 50 Hz Power consumption: 100 W Compressed air: 6–8 bar, without oil and water Weight: approx. 60 kg ✅ The set includes Piovan material feeders - visible in the photos.

Year of construction: 2008, condition: good (used), ROTOFLEX VLI 330 Inspection – Slitting – Rewinding Machine Manufacturer: ROTOFLEX International Model: VLI 330 Year: 2008 Serial No.: VLI 3517 Working width class: 330 mm Electrical: 380 V / 50 Hz / 3 Phase Condition: Very good working condition Current status: Still in production Availability: Approx. 3 months, after installation of the owner's new finishing line BRAND-NEW INSPECTION TECHNOLOGY BST TubeScan – Installed / Replaced in 2025 The machine is equipped with a modern: BST TubeScan Digital Strobe 4000 Inspection System The complete camera / inspection system was replaced in 2025 and is therefore almost new. This represents a considerable added value compared to many older Rotoflex machines currently available on the used machinery market. The system allows the operator to monitor the printed web during production and supports reliable quality control of finished labels. MACHINE APPLICATION The Rotoflex VLI 330 is designed for professional finishing and inspection of label material. Typical applications include: Dksdpjzww Ikofx Aa Isu · Inspection of printed labels · Slitting of master rolls into finished rolls · Rewinding · Removal and correction of defective material · Quality control · Preparation of finished rolls for delivery · Processing of pressure-sensitive label materials · Paper and film label applications

Condition: good (used), Year of construction: 2010, functionality: fully functional, OMET FlexyServo 330 mm Year of manufacture: 2010 Printing process: Servo-driven UV flexo Condition: Used – excellent condition Location: Europe _____ Machine Configuration • 6 x UV flexo printing units • 6 x GEW UV drying units • Double die-cutting stations • 1 x Gap Master system Dkodpsyyn Rwsfx Aa Isu • Turn bar (web turner) • Sheet-off unit with additional die-cutting station • Suitable for adhesive label production _____ Equipment & Tooling • 6 sets of tooling • 6 anilox rollers • 3 magnetic cylinders (currently in production) _____ Technical Highlights & Advantages This OMET FlexyServo is a modern servo-driven flexo press offering excellent register accuracy and efficient production performance. Key advantages: • Servo technology for high precision and reduced waste • Strong UV drying system (GEW) • Flexible configuration with multiple die-cutting options • Well-maintained machine in excellent condition • Immediate availability with testing possible This machine is ideal for converters looking for a reliable and efficient narrow web solution. _____

Condition: excellent (used), Year of construction: 2006, Battenfeld HM 270/1330H/1000H / 2K machine in very good technical condition / Operating hours: approx. 10,000 h in automatic mode Year of construction: 2006 Injection unit: Screw diameter: 55 mm Injection weight: 594 g Injection pressure: 2041 bar Metering volume: 653 ccm Clamping unit: Clamping force: 270 t Distance between tie bars: 710x710 mm Size of the clamping plates: 1030x1000 mm Ejector: hydraulic Clamping unit: hydraulic Control system: UNILOG B4 Additional equipment: Machine in very good technical condition 2K machine with horizontal injection units arranged in parallel Central injection Operating hours: approx. 10,000 in automatic mode Total number of operating hours: 11,876 h Control system with air valve Hydraulic core pull x 3 Reinforced injection units - bimetal Proportional valves on injection units - precise spraying Parallel movements Injection unit 1000H Screw diameter: 50 mm Injection weight: 446.8 g Injection pressure: 2016 bar Dosing volume: 491 ccm Dimensions Weight: 15000 kg Length/width/height: 6.90x1.78x2.34 m All offered machines are started by our service technicians before sale. Djdpfx Aoz Ipg Dea Ieku It is possible to obtain a video of the technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request

Condition: good (used), Year of construction: 2008, OMET Year of manufacture: 2008 Printing process: UV flexo Condition: Used – very good condition (single owner) Location: Italy _____ Machine Configuration • 8 x UV flexo printing units • UV curing system • 2 x die-cutting stations • 1 x Gap Master system • 1 x additional die-cutting unit for sheet-off • Sheet delivery with evacuation conveyor • Turn bar (web turner) • 3 x corona treatment units • Chilled impression cylinders with integrated chiller • Suitable for adhesive label printing _____ Equipment & Tooling • 3 sets of tooling • 10 anilox rollers Dkedpfxoyyn Snj Aa Iju • 3 magnetic cylinders _____ Technical Highlights & Advantages This OMET Flexy 330 offers a robust and versatile configuration, ideal for a wide range of label applications. Key advantages: • 8-color configuration for high flexibility • Corona treatment for improved ink adhesion • Chilled impression cylinders for consistent print quality • Well-maintained machine from single owner • Currently in production – inspection and testing possible This machine represents a cost-effective solution for converters seeking a flexible and efficient printing line. _____

Condition: excellent (used), Year of construction: 2002, Moba 330 Plateau Loader - Year 2000 Professional Moba 330 plateau loader, suitable for connection to both left and right configurations. The machine is inline deployable and can be converted to offline version by Bos Technical Support BV. The Loader is now in storage with us and available for immediate delivery. Description of the machine The Moba 330 plateau loader is designed for reliable and controlled Infeed of eggs to the grader. Thanks to its flexible configuration options, this plateau loader can be widely used within existing Moba lines. Dkedpfx Aox N Ecvea Iju The machine has always been serviced by a dealer and is in good but used condition. Due to its relatively low load and solid construction, this Loader is still excellent for long-term professional use. Technical specifications Specification Description Brand Moba Type 330 Plateau Loader Construction year 2000 Capacity 120000 eggs per hour Version Suitable for left and right Use Inline Conversion Conversion to offline possible Condition Good, used condition Maintenance Always dealer-maintained Availability Directly available from stock Features & capabilities Suitable for left and right configurations Inline deployment Offline conversion possible (by Bos Technical Support) Robust and proven Moba technology Easy integration into existing lines State of the machine The platform Loader is in good but used condition. The machine has been professionally maintained and technically checked. No overhaul performed - selling in current condition, fully functional, can also be delivered overhauled. Delivery, transportation & support Machine is in stock at Bos Technical Support BV Directly available Conversion to offline execution possible Transportation and support worldwide negotiable Contact Are you interested in this Moba 330 plateau loader or would you like additional information? Please contact Bos Technical Support BV without obligation. Are you interested in this Moba 170 Loader stand-alone or would you like additional information? Please feel free to contact Bos Technical Support BV for availability, price and delivery options. Sorteermachine eier verpakkingsmachine -eiersorteermachine egg gradingmachine sortiermachine sortieranlage eierverpackungsmachine MR 40 palletizer Maxipack, Moba, Sanovo, Staalkat, Prinzen, Rational, Kletec Yaskawa

Condition: new, Year of construction: 2026, functionality: fully functional, Technical Parameters: Cutting diameter: 330 mm Cutting range (90° flat): 350 x 330 mm Saw band length: 4900×34×1.1 mm Cutting speed: 15–150 m/min (adjustable) Max. workpiece weight: 670 kg/m Dkodsx H Rynspfx Aa Isu Total power requirement: 3.9 kW Table height: 750 mm Machine weight approx.: 2,600 kg Required space approx.: 1,700×2,400×2,200 mm Equipment: Laser line for cutting indication/marking Cutting process control Material monitoring Material database Feed force adjustment Zero stop Job menu Bundle cutting clamp Vertical roller Double-sided opening / reduced end scrap Operation and Comfort: Swiveling control panel LED work lighting Receiving table Water spray gun Chip and Coolant Management: Screw chip conveyor Micro-dosing Coolant level and flow control

Condition: new, neu ca. 4 Monate ab Auftragse Türkei 32000 € 611.2 € Doppelsäulenführung 5000 x 34 x 1,1 mm mm 20 - 120 m/min 330 mm 330 mm 350 x 330 mm 845 mm 1.1 kW 3 kW 0.12 kW 2815 mm Dsdpjwiq Hgsfx Aa Isku 1935 mm 1855 mm 2560 kg Servo feed with 700 mm stroke Cutting length up to 9,999 mm (multiple feeds) Omron touchscreen, 50 different cutting lengths and 30 programs can be saved Linear guide 41 mm saw blade Control panel Hydraulic vice Hydromechanical blade tension Heavy duty gearbox Coolant device Sensitive pressure Inverter for stepless blade speed Chip brush Optical height adjustment Chip conveyor Operating instructions in GERMAN or ENGLISH