Used Zeiss C100 413508 for sale (403)

Condition: new, Baldor BSC1005-24 drive controller ID: 21137B SN: 1295MG24816 – Input: 320VDC / Output: 0-250VAC, unused in opened original packaging, 100% functional, delivery as per photos Iedsy Npxbepfx Amijtg

Condition: ready for operation (used), Baldor BSC1005-24 servo drive, INPUT 320VDC, ID/No: 21137B, serial number: BEDBF038454, used, in good condition, fully functional, scope of delivery as per photos. Itodpfjy Npx Usx Amijg

Condition: ready for operation (used), Baldor DBSC1005-24-AAAW servo drive INPUT AC230V ID/No: 27992G serial number: 1698MG09743, used, in good condition, 100% functional, delivery as per photos. Iodpey Np Agjfx Amiotg

Condition: new, Baldor BSC1005-24 drive controller SN: BEDBA32401 - 320VDC / Output: 0-250VAC, unused in opened original packaging, 100% fully functional, scope of delivery as per photos Ijdjy Npxuopfx Amietg

Condition: ready for operation (used), Baldor BSC1005-24-HR servo drive, INPUT 320VDC, ID/No: 20707A, serial number: BDDBB20667, used, in good condition, 100% operational, delivery as per photos. Iedpsy Npyfjfx Amijtg

Condition: ready for operation (used), Baldor BSC1005-24V servo drive INPUT 320VDC ID/No: 21137A Serial number: BEDBA32402, used, in good condition, 100% functional, scope of delivery as per photos Ijdpfxsy Npzcs Amistg

Condition: ready for operation (used), Baldor DBSC1005-24-AAAW servo drive INPUT DC320V ID/No: 27991G Serial number: 2598MG13850, used, in good condition, 100% functional, scope of delivery as per photos Ijdpfx Asy Np Aaemijtg

Condition: ready for operation (used), Baldor DBSC1005-GAAW-2 servo drive INPUT DC320V ID/No: ASR28687G Serial number: 3899MG13652, used, in good condition, 100% fully functional, scope of delivery as shown in photos. Iedpfx Amjy Np A Toietg

Condition: ready for operation (used), Baldor DBSC1005-GAAW-2 servo drive INPUT DC320V ID/No: ASR28687G Serial number: 3899MG13654, used, in good condition, 100% functional, scope of delivery as per photos. Iedsy Np Ddepfx Amistg

Condition: new, Baldor BSC1005-24 drive controller ID: 21137B SN: 1295MG24826 - Input: 320VDC / Output: 0-250VAC, unused, 100% fully functional, delivery scope as shown in photos. Itsdpoy Npxnefx Amisg

Condition: ready for operation (used), Baldor BSC1005-24-HR servo drive INPUT 320VDC ID/No: 20707B SN: BDDBD22822, used, in good condition, 100% fully functional, scope of delivery as per photos Ijdpfx Amjy Npy Esietg

Condition: ready for operation (used), Baldor DBSC1005-24-AAAW servo drive INPUT DC320V ID/No: 27991G Serial number: 2098MG11447, used, in good condition, 100% fully functional, delivery as per photos Itodpfx Aoy Npz Nomisg

Condition: ready for operation (used), Baldor BSC1005-24 drive controller ID: 20207A SN: BEDBA32244, used, good condition, 100% functional, scope of delivery as per photos. Itsdpey Npw Djfx Amiog

Condition: ready for operation (used), Baldor BSC1005-24 drive controller ID: 21137B SN: 0595MG22118 - Input: 320VDC / Output: 0-250VAC Itedpfxey Npw Re Amiog

Condition: new, Baldor BSC1005-24 drive controller ID: 21137B SN: 1295MG24817 – Input: 320VDC / Output: 0-250VAC, unused in opened original packaging, 100% functional, scope of delivery as per photos Itodpfsy Npxhsx Amieg

Condition: new, Baldor BSC1005 servo drive ID: 20207A SN: BDDBD 22821 – Input: 320VDC / Output: 0-250VAC, unused in opened original packaging, 100% functional, scope of delivery as per photos. Itedpfxoy Npwwj Amisg

Condition: ready for operation (used), Baldor BSC1005-24-HR servo drive INPUT 320VDC ID/No: 21137B Serial number: 1295MG24824, used, in good condition, fully functional, scope of delivery as shown in the photos. Itedpfjy Npy Sjx Amisg

Condition: ready for operation (used), Baldor DBSC1005-GAAW-2 servo drive INPUT DC320V ID/No: ASR28687G Serial number: 4699MG17225, used, in good condition, 100% functional, delivery as per photos. Ijdsy Np Dkjpfx Amiotg

Condition: new, total length: 6,430 mm, Year of construction: 2026, lifting height: 6,300 mm, load capacity: 15,000 kg, Crane JMG MC 100.08 Itedpeyy Dghsfx Amiog Drive Electric Year built 2026 Lifting height (mm) 6,300 Lifting weight (kg) 15,000

Condition: used, Pallet with 18H7 T-slots, suitable for DMG DMC 100 H and DMG DMC 100 U as well as DMC 125H/U Duoblock. Itsdpjqx Uh Njfx Amieg More than 10 pallets available.

Condition: good (used), Year of construction: 2012, functionality: fully functional, Posmill C 1000, Year of manufacture: 2012, Control system: Fanuc Oi 100, Travel range X/Y/Z: 1000/530/630 mm, Tool changer: 30-position, BT 40, Itedsy Thw Dopfx Amiog Spindle speed: up to 10,000 rpm, Table size: 1150 x 560 mm, Maximum table load: 700 kg, Hexagon infrared measuring probe, Hexagon infrared tool measuring system, IKZ: 20 bar.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Itsdovf E Avepfx Amisg Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: ready for operation (used), Year of construction: 1998, travel distance X-axis: 260 mm, travel distance Z-axis: 1,020 mm, controller manufacturer: OKUMA, number of axes: 4, This 4-axis Okuma LU15 M-2SC 1000 was manufactured in 1998. It features two tool turrets, live tooling with C-axis capabilities, and synchronous tapping for enhanced productivity. The machine includes an integrated tool setter for precise measurements and a programmable tailstock for versatility. If you are looking to get high-quality turning capabilities, consider the Okuma LU15 M-2SC 1000 horizontal turning machine we have for sale. Contact us for further details. • Longitudinal Travel (X): 1020 / 995 mm • Cross Travel (Z): 260 / 140 mm • Turning Range: 340 mm • Swing Diameter over Bed Cover: 530 mm • Swing Diameter over Cross Slide: 380 mm • Spindle Nose: ASA-A2 / DIN 55026 Gr. 6 • Spindle Bore: 62 mm • Spindle Diameter in Front Bearing: 100 mm • Chuck Diameter: 200 mm • Main Drive: Motor spindle (hollow shaft motor) frequency-regulated 60% ED • Power (Main Drive): 22 kW • Max Torque: 412 Nm • Speed Range: 45 - 4,500 rpm Itjdpoy Nmi Djfx Amiog • Speed Levels (Electrical): 2 • Feed Drive: AC servo motors, digitally regulated • Feed Range X/Z: 0 - 1,000 mm/U • Rapid Traverse X/Z: 15 / 20 m/min • Power X, Z: 2.4/1.5 kW and 4/4 kW • Feed Force X, Z: 11/3.7 kN and 7/6.7 kN • Turrets: 2 tool turrets • Live tooling: Yes (C-axis and driven units) • Tapping: Synchronous tapping • Spindle interpolation: Automatic main spindle interpolation • Tool monitoring: Wear and breakage monitoring • Tool measurement: Integrated tool setter / measuring device • Tailstock: Programmable, towable with bed slide, automatic clamping • Tailstock quill: Controllable via M-command • Draw tube bore: 55 mm (partial hollow clamping cylinder) • Interface: DNC Interface RS-232C • Cooling system: Reinforced pump (8 bar at 30 l/min) • Programming: ONE TOUCH Dialog-NC (automatic work plan generation) Additional equipment • Chip conveyor (1,200 mm discharge height) Technical Specification Counter Spindle No Driven Tools Yes

Condition: used, Year of construction: 1983, operating hours: 6,270 h, power: 70 kW (95.17 HP), Equipment: all wheel drive, cabin, front linkage, * Manual transmission * Front and rear hydraulics & PTO shafts * Front and rear lift arms * Cab with 2 seats * Drawbar coupling * First registration: 17/08/1983 * Operating hours: 6,270 h ----* Front tire size: 520/75R26 * Rear tire size: 520/75R26 * Technical total weight: 7,000 kg * Curb weight: 4,280 kg * Overall length: 4,480 mm ----Vehicle number: 12039----Subject to errors and prior sale----We are happy to assist you with all formalities involved in purchasing a vehicle. Simply let us know your requirements and suggestions, and we will take care of them. Among other services, we can offer you the following for an additional fee:----* Trade-in of your old vehicle * TÜV/roadworthiness inspection * Complete export processing * Financing arrangement * Application for export license plates * Vehicle delivery * Vehicle registration * Recovery and vehicle transport ----YOUR VTS TEAM Isdpsy Rdgpefx Amiotg

Condition: good (used), Year of construction: 2008, functionality: fully functional, The Depo/ZPS machining center features an overhead gantry, meaning that all machine movements are performed by the tool. As a result, the mass of the workpiece and clamping device remains constant during machining. Year of manufacture: 2008 Spindle hours approx. 3,500 h (after spindle replacement in 2023) Control system: - Heidenhain iTNC 530 - Heidenhain HR 410 handwheel - Swiveling control panel with 15.1" monitor - Integrated Ethernet interface Technical Data Travel ranges: X 1,000 mm, Y 900 mm, Z 600 mm Work table: - 1,200 mm x 1,000 mm - Max. workpiece weight: 3,000 kg - Max. workpiece size: 1,000 mm x 800 mm x 700 mm Milling spindle: - Continuous power: 30 kW - Speed range: 1-18,000 rpm - Torque S1/100%: 80 Nm - Tool holder: HSK 63 form A - Main spindle jacket cooling - Air through spindle center for tool cooling (ILZ) - Coolant with 40 bar through the spindle (IKZ) Axes feed rates: - X, Y, Z axis feed up to 40 m/min - X, Y, Z axis rapid traverse up to 40 m/min Tool changer with double-arm gripper: - Number of tools in drum magazine (outside working area): 38 - Max. tool diameter: 80/115 mm - Max. tool length: 250 mm Tool and workpiece measurement for automatic tool and part size adjustment: - Tool radius and length measurement - Tool breakage detection - Blum laser for component measurement (Inspect) Disposal system: - Gooseneck slat conveyor - (Chip cart to be provided by buyer) Additional equipment: - Minimum quantity lubrication Minibooster 2 - Machine enclosure with full-area protective covers - Crane loading possible by unhooking the chip protection device at the front - Workspace lighting with two fluorescent lamps on the side walls Machine data: - Space requirement including service areas (LxWxH): approx. 5,000 mm x 4,220 mm x 3,830 mm Iodpfxjy Hp Rrj Amistg - Machine weight incl. additional units: approx. 13,000 kg - Connected load: 45 kVA, 400V, 50 Hz This machining center is located in a precision tool and mold making shop. It is exceptionally well-equipped with practical features and is in very good condition. The Depo/ZPS Dynamic 1009 operates precisely and reliably. There is no maintenance or repair backlog.