Used Slat Cabinet Press for sale (16,196)

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Nsdpfx Ajzuzw Deqwslf Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1996, Continuous press Manufacturer: OTT Type: 300-K-D0 Year of manufacture: 1996 Technical data Plate dimensions: 2550 x 1350 mm Hot water heating 6 pressure cylinders Total pressing force: 135 t Note: Nlodszuzwwspfx Aqwjf The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2007, Lamination press Manufacturer: Dimter Type: PROFIPRESS L2500 Year of manufacture: 2007 Technical data Wood dimensions to be processed Wood width, panels: 30 - 150 mm Wood thickness: 11 - 60 mm Wood inlet length: 800 - 2500 mm Panel widths, variable: max. 1300 mm Nledpfx Aozuzwqjqwof Specific pressing pressure for cross-sections of 2500 x 60 mm: up to 1.6 N/mm2 The pressing surface per press cycle must not be smaller than 100 cm2 Filling width of the press per cycle: min. 650 mm / max. 1300 mm Max. filling area of the press per cycle: 3.25 m2 (The max. usable press width depends on the widths of the individual lamellas.) Wood type Softwood/hardwood Press without options Electrical connection, press: 7 kW Electrical connection, 40 kW generator: 56 kW Operating voltage: approx. 400 Volt / 50 Hz (C/s) Collection table extended to 3700 x 1300 mm, with stainless steel wood support Motor-driven multi-function slider Lamination press Profipress L 2500 Press bed area approx. 2500 x 1300 mm Sturdy base frame with lower press table made of stainless steel as a grounding electrode Quick-change stop guide sets for panel thicknesses of 19 - 40 mm, which can be hydraulically adjusted to the current filling width Hydraulic special pressure elements ensure uniform pressure distribution over the entire joint length and compensate for tolerances In multi-lane operation, filling widths may vary by a maximum of 15 mm Upper pressure plate with hydraulic drive generates high vertical pressing pressure for minimal displacement Integrated hydraulic unit for generating pressing force and driving the hydraulic motors Control cabinet and control panel Protective cladding Additional individual pressure elements from above Automatic gluing station with precision gluing head Infeed for different widths Camera Washing and rinsing device for gluing head Modem incl. software for online connection Note: The technical data and descriptions are copies of the order confirmation from that time. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2019, Corpus press Manufacturer: LINYI JIANZHONG WOOD MACHINERY Type: JJZ-CP Year of manufacture: 2019 The JJZ-CP press is suitable for the production of plywood, doors, and MDF panel joints. The feeding and removal of the glued elements are carried out automatically via powered roller conveyors. Technical data - Max. pressure 500 t (adjustable) - Max. filling height 1300 mm Nledpfxezuzwko Aqwjf - Min. filling height 900 mm - Max. filling size 1300 x 2500 mm - Press dimensions 3600 x 1370 x 4500 mm - Press placement approx. 500 mm below floor level - Feeding table 2000 x 1960 mm - Receiving table 2350 x 2500 mm - Max. power 13.2 kW - Weight 12000 kg - CE marking - Capacity: 6 batches per hour 2 corpus presses are available for sale. Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1998, Continuous body press Manufacturer: LIGMATECH TYPE: MPP 15 Year of manufacture: 1998 The MPP 15 is a flexible press for batch-related production without setup times. The MPP 15 can be used individually or in various combinations in an assembly line. The pressing forces are applied pneumatically. The separately adjustable vertical and horizontal pressure allows for pressing both horizontal and vertical bodies. The vertical forces are transmitted through a plate, while the horizontal forces act on the body via press cheeks. Nodpfx Aezuzv Tsqwjlf The position of the center press cheeks can be adjusted using adjustable stops, allowing for different heights of bottoms and sides. During the infeed process, the body is measured photoelectrically, which automatically positions the horizontal pressure bar. Technical data: Body dimensions: Length: min. 300 mm / max. 2300 mm Height: min. 300 mm / max. 1220 mm Depth: max. 600/800/1000 mm (depending on the press type) Pressing pressure: vertical max. 17 kN horizontal max. 16 kN Working height: 500 mm Transport speed: min. 8 m/min. / max. 37 m/min. Pressing time: selectable up to 999 s Operating voltage: 400 V, 50 Hz Control voltage: 24 V DC (according to VDE) Required air pressure: 5...8 bar Air consumption: 120 NL/cycle Total connected load: 3 kW Weight: approx. 4 tons Required room height: 3000 mm Extended infeed belt as a staging area Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2000, Corrugated board press Manufacturer: Hüttenhölscher Year of manufacture: 2000 Nlsdpfxszuzvme Aqwjf Technical data Voltage: 400 V Current: 32 A Frequency: 50 Hz Compressed air: 6 bar Note: The technical data and descriptions are a transcript of the order confirmation from that time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2020, total length: 2,450 mm, total width: 1,900 mm, total height: 2,140 mm, Weight: 5.500 kg - Year: 2020 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Drive system: CNC - Control system brand: Delem - Control system type: DA-41s - Power [kW]: 4.0 - Number of axes [pcs]: 4: Y1+Y2+X+R - Press force [ton]: 40 - Max. working width [mm]: 2000 - Column gap [mm]: 1800 - Throat depth [mm]: 200 - Backgauge depth [mm]: 750 - Max. stroke [mm]: 100 - Crowning system: None - Punch holder: Quick-release - Tool holder type: European-style - Tools included: Yes - Options: Finger safety guard - Transport dimensions: 2450mm x 1900mm x 2140mm (l x w x h) - Transport weight [kg]: 5500kg - Transport packages [pcs.]: 2 Nlsdpfx Aqozr Inwjwjf Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: excellent (used), Year of construction: 1996, Toggle Press Schling Pressing force 60KN (6000 kg) Stroke adjustable from 0 to 25 mm Very clean and in very good condition Nlsdpozwkpbjfx Aqwof

Condition: used, Year of construction: 2001, Short-cycle pressing line Manufacturer: Wemhöner Type: KT-F-1E Year of manufacture: 2001 Technical data - Pressing area: 5,750 mm x 2,200 mm - Operating side: left - Plate dimensions: Length: 2 x 2,600 mm - 2 x 2,620 mm Njdpfx Aozuzi Toqwelf Width: 2,070 mm Thickness: 6 mm - 40 mm - Pressing pressure: approx. 40 kg/cm² Note: Upon request, the complete layout plan of the system can be sent. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 1998, - Lengths: 1,800 - 2,300 mm - Widths: 500 - 1,300 mm - Thicknesses: 35 / 40 / 44 mm Door pressing system Manufacturer: Wild Year of manufacture: 1998 For door dimensions: - Lengths: 1,800 - 2,300 mm Nledpfxezuzgrj Aqwjf - Widths: 500 - 1,300 mm - Thicknesses: 35 / 40 / 44 mm Consisting of the following sections: 1. Continuous door panel gluing with frame assembly station / 2. Pressing line with hardboard facing station Section 1 consists of: - Gantry loading system - Angle transfer with longitudinal and cross saws - Loading and feeding of the longitudinal and transverse frame parts from magazines - Longitudinal cutting station for the longitudinal frame parts - Connecting station of the frame parts with the door panel core. With clamping devices - Conveyor belt angle transfer with shuttle transfer of the door panel cores onto the glued hardboard Section 2 consists of: - Loading of the hardboard - Brush cleaning machine - Hardener application machine from below - Glue application machine from below - Roller conveyor - Angle transfer for the lower hardboard - Vacuum reversing device for the upper hardboard - Automatic facing station for hardboard and door panel cores - 2 door presses, each with 2 x 4 pressing stations, arranged parallel to each other - Both presses are loaded at the infeed with 1 shuttle loading basket - Both presses are unloaded at the outfeed with 1 shuttle unloading basket - Angle transfer to the infeed into a hedgehog buffer - Angle transfer at the outfeed of the hedgehog buffer and feeding to the stacking station - One-sided vacuum stacking with protective plate space Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: like new (used), Year of construction: 2023, functionality: fully functional, PLEASE READ CAREFULLY!!! THIS OFFER IS EXCLUSIVELY FOR EUROPEAN END CUSTOMERS, AND THE FIRST INQUIRY MUST INCLUDE COMPLETE CONTACT INFORMATION. THANK YOU. The forging line consists of a hydraulic 1500-ton forging press, an induction unit with 1200 kW, and a robot with a load capacity of 300 kg. So far, prototypes have been manufactured; however, the line was actually designed for series production, which has not yet taken place. The line was built and installed in 2023. The technical specifications are as follows: Hydraulic press 1500 tons (year of manufacture 2023) SIEMENS control system - Pressing force: 1500 tons - Retraction force: 120 tons - Downward stroke: 300 mm/s - Pressing stroke: 100 mm/s - Upward stroke: 300 mm/s - Installation height: 3,000 mm - Ram stroke: 1,500 mm (!) - Ram size: 1,600 x 1,600 mm - Table size: 1,600 x 1,600 mm Nljdpfx Aqezvnpijwjf - Ejection force / 1 position: 40 tons - Stroke: 600 mm - Ejection speed: 250 mm/s - Return speed: 250 mm/s - Stroke: 400 + 400 mm - Traverse speed: 200 mm/s - Ram positions: 3 positions Including a 1200 kW induction unit (year of manufacture 2023) MITSUBISHI control system - 1200 kW / 450 Hz induction unit for billets - Coil size: Ø 215 / Ø 150 mm, two sets of coils - Material feeding system Including a Kawasaki robot (6 axes) – Model: ZX300S-D- (year of manufacture 2023) - Max. load capacity: 300 kg - Max. reach: 2500 mm Sample images of the machines are attached.

Condition: used, Year of construction: 2015, Technical specifications: - Manufacturer: Weger air solutions Nedsykuz Ajpfx Aqwelf - Year of manufacture: 2015 - Model: ZL66 - Motor output: 1.27 kW - Length: 2,900 mm - Width: 705 mm - Height: 890 mm - Duct connection: suction 605x655 mm, discharge 605x560 mm - Heating medium: hot water PWW 70/50 - Airflow: 3,000 m³/h - Heating pipe connection diameter: DN 32 mm - Voltage: 230V - Location: in stock - Voltage fluctuation max. +/- 5%

Condition: new, pressing force: 100 t, stroke length: 400 mm, clearance between the columns: 1,010 mm, overall weight: 1,000 kg, - Capacity 100 tons - Cylinder stroke 400 mm - Working width 1010 mm - Electrically or manually operated Nsdpfxjr Ei Sze Aqwelf - pressure gauge - Emergency stop - 400V

Condition: ready for operation (used), number of spindles: 4, - Benchtop model - 4 drilling spindles - Foot switch - 380/400V 50Hz Nsdozv D D Nspfx Aqwjlf 4 new drive belts have been installed.

Condition: good (used), Year of construction: 1981, operating hours: 376 h, functionality: fully functional, machine/vehicle number: 01031, total height: 3,200 mm, total width: 1,900 mm, total length: 2,500 mm, table width: 570 mm, table length: 670 mm, overall weight: 10,000 kg, clamping force: 400 kN, input frequency: 50 Hz, input current: 25 A, power: 7.5 kW (10.20 HP), REIS TUS 600 K Coating Press Nedpfx Aqszlfb Iewjlf - Operating voltage: 380/260 V Attention: The item must be picked up between September 8 and September 10, 2026, on a date to be confirmed. FCA D-63128 Dietzenbach - loaded onto a truck.

Condition: used, Year of construction: 2006, functionality: fully functional, year of last overhaul: 2022, SCHULER GRÄBENER TMK 2-630 – 630 t Punching and Forming Press with Coil Feeding System Manufacturer: SCHULER / Gräbener Pressensysteme Type: TMK 2-630-3.0-50/210 S Year of Construction: 2006 Press Force: 6,300 kN / 630 t Design: Mechanical Punching and Forming Press / Single-Action Press For sale is a SCHULER GRÄBENER TMK 2-630 mechanical single-action press / punching and forming press with a press force of 6,300 kN, including a complete SCHULER automation strip guiding, straightening, and coil feeding system. The system was used for the mass production of punched and formed parts and is currently still fully assembled on site. Technical Data Press Rated Force: 6,300 kN Rated Stroke: 12 mm Stroke: 50–210 mm Stroke Rate: 15–60 strokes/min Max. Flywheel Speed: 960 1/min Ram Adjustment: 200 mm Max. Installation Height: 800 mm Table / Tooling Area: approx. 3,000 × 1,500 mm Max. Tool Dimensions: 3,000 × 1,500 × 800 mm Max. Tool Weight: 12,000 kg Drive Power: max. 280 kW Rated Current: 420 A Compressed Air: 6 bar Hydraulic System: 400 bar Clutch / Brake: 6 bar Permissible Switching Rate Clutch / Brake: 16/min Machine Weight without Accessories: approx. 138,000 kg Coil and Feeding System SCHULER Automation / Gräbener Pressensysteme, Year of Construction 2006. Coil / Uncoiling Unit: Type AC-LH-160-0650 Strip Width: 40–600 mm Coil Outer Diameter: 900–1,800 mm Spreading Range: 470–530 mm Coil Uptake / Uncoiling Strip Guiding and Straightening System Threading / Strip Guiding Devices Automated Material Feeding Roller Guides Conveying / Removal Technology Complete Protective Enclosure Control / Operation SCHULER System Control Siemens SIMATIC Operating Components Siemens SIMATIC OP17 Touch Panel Separate Operating Panel for the Feeding System Setup Operator Devices Unidor Process / System Monitoring Condition and Maintenance The system was overhauled in 2022 for approximately €85,000. Njdpfxezv Utnj Aqwslf The maintenance history has been regularly recorded. Current maintenance and repair records are also available for 2026. The system is fully assembled on site and can be inspected by appointment. Scope of Supply The press system is sold, including the associated SCHULER automation and the existing coil, strip guiding, straightening, feeding, and removal technology, as well as the associated protective enclosure and operating / control devices, according to the existing system scope. Complete Service from a Single Source Upon request, we offer a complete project management service for this system – from financing to installation and commissioning at the new location. Possible Services: Individual financing and leasing solutions Organization and support for disassembly Heavy-load loading and transport International transport and export processing Organization of crane and heavy-load operations Reconstruction and assembly at the new location Support during commissioning Coordination of required service and specialist companies This allows the system to be taken over not only at the current location, but also as a completely organized machine project, depending on the customer's requirements. Location: Germany Availability: by arrangement Inspection: by appointment Disassembly / Transport / Reconstruction: can be completely organized upon request Financing / Leasing: upon request Technical data based on available documents and nameplates, subject to change and prior sale.

Condition: good (used), Year of construction: 2018, operating hours: 40,350 h, Baling press Presona LP 85 VH2, year of manufacture 2018 Technical data: Manufacturer Presona Sweden Type LP 85 VH2 Year of manufacture 2018 Nlsdpjzulknjfx Aqwef Drive power 2 x 45 kW Operating hours 40,350 Effective operating hours approx. 22,000 Pre-compression force 28 t Main compression force 85 t Feed opening 1500 x 1100 mm Bale dimensions 750 x 1100 mm Bale weight 450 - 650 kg Theoretical volumetric capacity: 1200 m³/h Throughput capacity at 30-100 kg/m³: 13-30 t/h Tying 5-strand vertical, (3-strand horizontal) Oil tank volume 2000 L Transport dimensions of press 10400 x 2400 x 2800 mm (LxWxH) Weight approx. 27000 kg Materials: Paper, cardboard, PET bottles, films, light waste. Note: The press is in good condition. It has been dismantled from ongoing operation. The following work has been carried out by us: New wear plates (Hardox) in the press channel Seals completely replaced on the main cylinder Oil filter changed Vertical tying mechanism overhauled and made functional The horizontal tying mechanism is currently not functional. The technical documentation is available. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and any possible errors. The offer is subject to change, prior sale is reserved, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment ex works, without warranty.

Condition: used, Year of construction: 1967, total length: 2,000 mm, total width: 1,750 mm, total height: 2,850 mm, Colour: Grey Empty weight: 6.000 kg - Year: 1967 - Documentation available: No - CE certificate present: No - Serial number: 1166 - Drive system: Conventional - Press model: C-Frame press - Press force [ton]: 100 - Max. stroke [mm]: 250 Njdpfx Aszry Icsqwjlf - Table length [mm]: 740 - Table width [mm]: 500 - Ram length [mm]: 250 - Throat depth [mm]: 350 - Transport dimensions: 2000mm x 1750mm x 2850mm (l x w x h) - Transport weight [kg]: 6000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2023, total length: 1,400 mm, total width: 600 mm, total height: 2,180 mm, Colour: Blue Empty weight: 280 kg Nsdszry H Ejpfx Aqwolf - Year: 2023 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: SA021 - Drive system: Conventional - Press model: Workshop press - Press configuration: Single-acting - Press force [ton]: 30 - Min. stroke [mm]: 0 - Max. stroke [mm]: 190 - Table length [mm]: 695 - Table width [mm]: 60 - Ram width [mm]: 60 - Max. opening height [mm]: 1000 - Height adjustment [mm]: 830 - Transport dimensions: 1400mm x 600mm x 2180mm (l x w x h) - Transport weight [kg]: 280kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, total length: 1,250 mm, total width: 2,100 mm, total height: 3,300 mm, Colour: Green Nsdpozrxr Tofx Aqwjlf Empty weight: 7.000 kg Price: On request - Documentation available: No - CE certificate present: No - Drive system: Conventional - Press model: C-Frame press - Press configuration: Single-acting - Press force [ton]: 100 - Min. stroke [mm]: 20 - Max. stroke [mm]: 140 - Table length [mm]: 580 - Table width [mm]: 780 - Ram width [mm]: 400 - Throat depth [mm]: 315 - Max. opening height [mm]: 560 - Height adjustment [mm]: 70 - Pressing speed [mm/s]: 360 - Transport dimensions: 1250mm x 2100mm x 3300mm (l x w x h) - Transport weight [kg]: 7000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2007, total length: 3,550 mm, total width: 1,800 mm, total height: 2,800 mm, Colour: Grey Weight: 10.000 kg - Year: 2007 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes Nlsdpfxozrxfts Aqwof - Serial number: 11520 - Drive system: CNC - Control system brand: Baykal - Control system type: EC4-CNC - Power [kW]: 11.0 - Number of axes [pcs]: 3: Y1+Y2+X - Press force [ton]: 150 - Max. working width [mm]: 3100 - Column gap [mm]: 2550 - Max. stroke [mm]: 260 - Crowning system: CNC-controlled - Punch holder: Quick-release - Tool holder type: European-style - Transport dimensions: 3550mm x 1800mm x 2800mm (l x w x h) - Transport weight [kg]: 10000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 1964, total length: 2,100 mm, total width: 1,500 mm, total height: 1,850 mm, Colour: Green Weight: 2.500 kg - Year: 1964 - Documentation available: No Nlsdpfozc Irrox Aqwof - CE certificate present: No - Serial number: 13120 - Drive system: Conventional - Number of axes [pcs]: 1: Y1 - Press force [ton]: 50 - Max. working width [mm]: 2000 - Backgauge depth [mm]: 0 - Punch holder: Fixed - Tool holder type: European-style - Tools included: Yes - Transport dimensions: 2100mm x 1500mm x 1850mm (l x w x h) - Transport weight [kg]: 2500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2001, operating hours: 2,500 h, total length: 3,540 mm, total width: 1,500 mm, total height: 2,330 mm, Colour: Grey Weight: 8.230 kg - Year: 2001 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 5356 - Operating hours: 2500 - Drive system: Conventional - Power [kW]: 11.0 - Number of axes [pcs]: 3: Y1+Y2+X - Press force [ton]: 160 Nljdpoy Thmxsfx Aqwjf - Max. working width [mm]: 3100 - Column gap [mm]: 2500 - Backgauge depth [mm]: 750 - Max. stroke [mm]: 200 - Crowning system: None - Punch holder: Standard - Tool holder type: European-style - Tools included: Yes - Transport dimensions: 3540mm x 1500mm x 2330mm (l x w x h) - Transport weight [kg]: 8230kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: ready for operation (used), Year of construction: 2008, pressing force: 66 t, stroke length: 200 mm, throat depth: 400 mm, total width: 2,650 mm, total height: 2,400 mm, overall weight: 5,800 kg, Equipment: CE marking, Hydraulic press brake Manufacturer: TRUMPF, Type: TruBend 3066 Year of manufacture: 2008 Nodpfxjzu Tawo Aqwjlf Technical data Manufacturer: TRUMPF Type: TruBend 3066 Year of manufacture: 2008 Bending length: 2040 mm Press force: 66 t Free daylight between uprights: 2364 mm Throat depth: 400 mm Stroke: 200 mm Y-axis rapid traverse speed: max. 200 mm/s Y-axis working speed: max. 15 mm/s Drive power: 17 kW Dimensions: L 2.65 x W 1.85 x H 2.40 m Weight: 5650 kg Equipment - Electro-hydraulic upper drive - Block hydraulics - Controlled axes: Y1, Y2, X, R, Z1, Z2 - Automatic upper and lower tool clamping - Self-adjusting crowning system - Control system: Delem - Light curtain at the front for laser safety - Foot switch - Tool package consists of: Upper tool, straight, 28°, R1, 2000 mm, segmented Lower tool, V10, 84°, H100, 2000 mm, segmented All information is subject to change without notice.

Condition: used, Year of construction: 1961, pressure 025 t table-size 450 x 500 mm stroke 500 mm dayligth 550 mm throat 200 mm Nlsdoxukpcepfx Aqwof table height over floor 800 mm hole in the table 130 mm