Used Seegräber Gmbh Td33 for sale (68,211)

Condition: new, Year of construction: 2026, Equipment: safety light barrier, 1A Gmatick Storage Paternoster (roll rack) The foil storage Paternoster foils is suitable to use for the storage of all 3D-films, it is used as a high storage at the membrane press or as a space-saving storage solution for the 3D foils. With our Paternoster you can storage on very small area approximately 2, 4m x 1, 2m a lot of film rolls (up to 32 rolls of a Ø 300 mm). The required film is thus immediately available at the push of button. Our Paternoster are available from 2.8 m up to 6, 0 m as standard Paternoster. Also special solutions are offered by us, please contact us, we will then find the right solution for your storage. As additional equipment we offer center sleeves, a manual cutting station or the full automatic cutting device and we have also ionization solutions available at Gmatick. • Storage rods ø 42.4 mm • Sleeves inside Ø max. 82 mm,. • Load chain as a hollow pin chain with a breaking load of 100 kN, • Chain pitch is 50 mm hole to hole and this is the raster for the positioning of the mounting foil bars. Nedpsff Huwefx Abyedc • Control with a key switch (dead man) for on / off • Rotational speed of the chain is approx. 5.5 m / min • Voltage 400 V, 3N; 50/60 Hz or as USA Version 480V 60Hz • Mains cable with CEKON plug 16A fuse protection (by the customer) 10A slow blow • ground load data at least 2, 2 kg / cm² • Side covering over the entire height of the Paternoster, guards from 2, 2 m above floor to top edge of the Paternoster. • Requirement for the installation of the Paternoster is a viable, flat and solid floor, • Floating floors you can’t install a Paternoster. It is forbidden

Condition: new, functionality: fully functional, machine/vehicle number: 0681, empty load weight: 2,100 kg, maximum load weight: 16,000 kg, overall weight: 18,100 kg, axle configuration: 2 axles, next inspection (TÜV): 09/2026, wheelbase: 4,000 mm, color: orange, Year of construction: 2025, Equipment: center pivot plate, The TPW 16 VL - LK has a payload capacity of 16,000 kg on the loading platform at 6 km/h. The dimensions are 5,000 mm long, 2,000 mm wide, and approximately 640 mm high. It features a turntable steering system on the front axle and a rigid trailing axle. The drawbar is equipped with a drop safety device, and the forged towing eye has a 40 mm bore. Heavy-duty banded tires 425 x 150-305 are fitted as twin wheels on steel rims and sealed on both sides with tapered roller bearings using a Nilos ring. For safety, four welded-on lashing brackets are fitted to the longitudinal sides (for load securing), and a double-acting wheel chock is mounted on the frame. The paint finish is yellow-orange RAL 2000. The transport floor is made of 30 mm tongue-and-groove boards, countersunk and bolted. Ndsdpfx Aorcfz Tsbyec

Condition: as good as new (ex-display), Year of construction: 2025, operating hours: 500 h, functionality: fully functional, machine/vehicle number: 25-029, total width: 800 mm, total length: 4,700 mm, total height: 1,900 mm, type of input current: three-phase, energy consumption: 2 kWh, Very good metal separator (inductive sorter) for separation of all kinds of metal (incl. stainless steel). Can be used before ECS, behind or stand alone. Ejecting of all metals larger 0.5 / 1 mm possible. Reasonable using for material up to 60 % metal content. Unique flap technology, no pressured air necessary. Machine is ready for using, can be visited or tested. If wished can be equipped with camera. Nodsqabm Eopfx Abyodc If the machine is too small we can build also bigger. It is our demonstration machine. Throughput / capacity depending on material and purpose. Price on negotiation!

Condition: good (used), Used, insulated stainless steel tank with agitator and double jacket Last use: Food Article number: 10340 Volume: Approx. 6300L Type: Standing on three legs Material (in contact with media): 1.4301 / AISI304 Design: Insulated with double jacket at the bottom Bottom: Flat bottom Top: Domed Operating pressure according to nameplate: ATM Tank dimensions: Tank diameter: 2030mm Cylindrical height: 2000mm Nodpfx Absd Nap Rsysdc Distance from outlet to bottom: 330mm Height of legs: 390mm Overall height: 2940mm Overall width: 2050mm Materials: Inside: 1.4301 / AISI 304 Outside: 1.4301 / AISI 304 Equipment: Domed lid Ø 490mm Outlet diameter: 40mm Slow-speed agitator Cylinder insulated Bottom with double jacket

Condition: like new (used), Used heatable/coolable stainless steel container Type: STOC3300TPRW Item number: 10844 Volume: Approx. 3300 liters Type: Upright design on three height-adjustable feet Design: Single-walled with thermoplate Material (wetted parts): 1.4301 stainless steel (AISI304) Surface: Satin-finished outside, BA (IIId) inside Internal weld seams: Pickled, passivated and brushed Max. Operating pressure: Atmospheric Max. Operating pressure thermoplate: 1.8 bar Max. Operating temperature: 95°C Top plate: 15° conical bottom Bottom: conical bottom 15° with central outlet DN50 DIN11851 Tank dimensions: Njdpfxeuy Ribs Abysdc Tank diameter: 1600mm Cylinder height: 1500mm Total height: 2430mm Equipment: 1x Ø 500mm manhole cover with swivel bracket on the top, EPDM seal 1x ladder bracket 1x thermoplate on cylinder H=900mm on cylinder 1x agitator flange connection IEC250 3x spherical caps / height-adjustable feet with foot plates 1x vent valve DN50 stainless steel unpressurized on the top plate 1x DN50 DIN11851 spigot outlet in the center of the underbody 1x DN50 DIN11851 spigot on the top shelf with blind cap 1x DN65 DIN11851 spigot on the top shelf with blind cap 1x type plate

Year of construction: 2026, condition: new, functionality: fully functional, overall weight: 120 kg, total length: 900 mm, total width: 1,550 mm, total height: 2,050 mm, input frequency: 50 Hz, laser power: 30 W, laser wavelength: 1,064 nm, type of cooling: air, type of input current: AC, laser type: fiber laser, The universal laser marking system LAS 28 XLe from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser you can mark almost all materials such as steel, carbide, aluminum and plastics. Depending on the requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of the laser is necessary in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be realized with just a few clicks without extensive programming knowledge. Serial and article numbers are automatically incremented by the software after prior setting. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. The standard equipment includes an integrated PC with Windows operating system and laser software. Optionally, the laser model LAS 28 XLe can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as lateral extension arms for marking long parts, movable Z-axis, drawer systems, etc., can be realized. Made in Germany Fiber laser 30W, 20 W or 50 Watt - Laser class 1 - Wavelength 1064nm - Marking field size 150x150mm (optionally larger) - marking software EZCAD in German / English - optional: rotary axis (3-jaw chuck) - optional: digital height measuring system - optional: exhaust system (incl. activated carbon filter) - pilot laser (simple preview, contour preview) - focus finder (simple focus adjustment) - signal light for indication of operating status - max. component height approx. 300mm - electrically adjustable Z-axis Ndjdozntfmepfx Abyoc - Integrated PC with Windows operating system - frame made of aluminum profile - air cooled - Door width approx. 700mm / door height(pass-through): 400mm - Connection 230V - Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) - Weight: approx. 100 Kg

Condition: new, functionality: fully functional, For sale is one (1x) safety door switch with the article number 541010. This item comes from warehouse stock / spare parts stock. Ndedpfx Ajzxpvpebyec The optical condition can be seen in the attached images. We will gladly provide further technical documentation or detailed images upon request. Inspection and collection are possible by arrangement. Shipping is possible at the buyer's expense. Subject to prior sale, errors and changes.

Condition: ready for operation (used), Year of construction: 2016, machine/vehicle number: 16274986/1, functionality: fully functional, Multiripsaw for edging boards, max cutting height 125 mm, max passage 950 mm, el.power 75 kW Ndjdpfx Aboz N Tfueyec operating panel, conveyors

Condition: ready for operation (used), Year of construction: 2019, functionality: fully functional, machine/vehicle number: 1 790 58 450, turning length: 990 mm, turning diameter: 160 mm, spindle speed (max.): 4,500 rpm, spindle speed (min.): 1,500 rpm, travel distance X-axis: 280 mm, travel distance Z-axis: 2,400 mm, spindle motor power: 30,000 W, rapid traverse X-axis: 30 m/min, rapid traverse Z-axis: 100 m/min, rotational speed (min.): 1,500 rpm, rotational speed (max.): 4,500 rpm, total height: 2,950 mm, total length: 5,550 mm, total width: 2,550 mm, feed length X-axis: 280 mm, feed length Y-axis: 2,400 mm, feed rate X-axis: 30 m/min, feed rate Z-axis: 100 m/min, type of input current: three-phase, torque: 191 Nm, overall weight: 16,000 kg, chuck outer diameter: 215 mm, spindle nose: A6, mount diameter: 40 mm, Equipment: documentation/manual, rotational speed infinitely variable, Manufacturer: J.G. WEISSER SÖHNE GmbH & Co. KG Type: UNIVERTOR AS90/650RT General features: Machine type: Horizontal shaft turning center with pick-up loading Area of application: Complete machining of shafts and rotationally symmetrical components Loading: Pick-up automation Processing types: Green turning, hard turning, roughing, finishing Tool carrier: 12-way turret with electric drive (VDI 40) Additional options: Driven tools, rotary turning, NC-adjustable steady rest, measuring probe Main spindle: Spindle bearing diameter: 90 mm Spindle flange: A6 according to DIN 55026 Nedpfx Absvxf U Esysdc Drive power (100/40% ED): 18/23 kW or 23/30 kW Nominal speed: 1,500 rpm Maximum speed: 4,500 rpm Torque (100/40% duty cycle): 115/146 Nm or 151/191 Nm Travel paths & axes: Max. turning diameter: 160 mm Max. chuck diameter: 215 mm Center distance: Max. 990 mm Travel paths X/Z axis: 280 mm / 2,400 mm Max. feed force X/Z (40% duty cycle): 10 kN / 8 kN Max. travel speed X/Z: 30 m/min / 100 m/min Tailstock: Pressure force: 850 daN Centering center holder: MK4 Max. speed: 4,500 rpm Dimensions & weight: Machine dimensions (L×W×H): 5,550 × 2,550 × 2,950 mm Weight: 16,000 kg

Condition: new, Factory-new electrically heated 1150L stainless steel agitator tank with insulation and propeller agitator, including operating manual and CE declaration of conformity. Type: EBB1150RWP Also available with alternative agitators and in other sizes. Volume: 1150L Dimensions approx.: Internal Ø 1190mm x cylindrical height 1000mm External Ø: 1390mm Total height: approx. 1300mm plus agitator drive Material: 1.4301 / AISI304 stainless steel Surface: IIIc/IIId / satin finish Internal welds ground smooth Max. operating temperature: 110°C Max. operating pressure: atmospheric - Upright design on four tubular legs with forklift channels - Top: Central traverse with two hinged covers - Bottom: Flat sloped base with lateral outlet DN50 DIN11851 and butterfly valve, EPDM gasket - Insulation: 50mm mineral wool around the cylinder, hermetically welded stainless steel 1.4301 cladding Ndjdpfxow Dy D Do Abyec Equipment: 1x Top traverse with two hinged cover halves, clamp function for the lid Stainless steel grating below the hinged lid, bolted and removable 1x Agitator flange on the top 1x Inlet port DN50 DIN11851 on the top 1x Outlet fitting with butterfly valve DN50 DIN11851, EPDM gasket 1x nameplate Propeller agitator for low-viscosity media Power: 0.75 kW Speed: 1410 rpm Operating voltage: 3PH 400V

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, Technical specifications: Operating voltage: 400V AC, 3PH/PE Frequency: 50Hz Connected load: 110kVA Main supply fuse: 200A Production capacity: depending on material to be processed, 20m/min / 6" core up to max. 830mm diameter / up to 1.4t Degree of automation: fully automatic Nsdjxzuc Hjpfx Abyodc Installation dimensions: 5.2x3.7x3.2m (LxWxH)

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, Precision winding machine for films and web materials. Designed for consistent unwinding, guiding, and rewinding of roll materials. Integrated safety system with protective glazing, laser start position indicator (green), emergency stop switches, and pneumatic film guiding. Machine frame made of steel, electrically controlled drive. Ideal for production lines in coating or laminating technology. Ndodpfx Abjxzuiyjyjc

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: PM3, Universal testing machine PM3 (2026) Force: 3 kN Crosshead travel: 520 mm Working space depth: 66 mm Overall height: 1036 mm Weight: approx. 40 kg Displacement resolution: 0.01 mm Testing speed: 1-500 mm/min Cc7d2rmq Return speed: 700 mm/min Load cell: 3 kN Includes evaluation electronics and basic software. Njdpfx Aeyc U Dbsbyjdc Our testing machines can be operated in stand-alone mode via a numeric keypad, allowing for a “quick test” even without a PC. For tests that require data storage and recording of the curve profile, we offer the option to control and evaluate the tests using the basic software. This allows you to generate various test sequences and create a test report. Furthermore, you have the option to process the raw data in your own programs. Optional: - Delivery and commissioning - DAkkS or factory calibration according to DIN EN ISO 7500-1 - Clamping devices: Pressure plates, bending fixtures, shear fixtures, wedge clamps, scissor clamps, peeling clamps, screw clamps, pneumatic clamps, and hydraulic clamps.

Condition: used, Year of construction: 1991, 2 vertical stainless steel tanks with dished bottoms, shell cooling zone, manhole, sampling tap, insulation and central outlet. Additional title: 2 insulated, coolable tanks Volume: 44361 l Operating pressure: 0,9 bar Operating temperature: 20 °C Material: stainless steel Position: vertical Base construction: cylindrical tank with dished bottoms, placed an 4 square tube feet Features: insulated, covered, 1 cooling zone (183 l, 0.9 bar), manhole, safety valve, CIP pipe with spray head, manometer, yeast plug Ndodpfx Aoztya Uebyec Periphery: own temperature control

Condition: used, Year of construction: 1986, A vertical stainless steel tank with multiple cooling zones and various fittings. Most recently used as a fermentation tank for beer. Additional title: Coolable tank Capacity approx.: 11600 l Width: approx. 2,3 m Height: approx. 4,1 m Material: Stainless steel Position: vertical Base construction: on 4 feets Features: manhole; cooling jackets; spunging apparatus; sampling valve Njdpfx Aszty E Robysdc

Year of construction: 1990, condition: used, Capacity: 250 hl/h Pressure: 16 bar Length: 3.000 mm Width: 750 mm Height: 2.246 mm Weight: 3150 kg Material: plates: 1.4404/0,8mm 196 WAP, 59 HHP, 3 AP / seals: Perbunan PRESS IN Base construction: clamping screw cap NIRO pedestal Features: 4-stages (heater, hot holding section, regenerative heat exchanger, pressure reduction), connections: DN65 Ndodpfx Abezty Hnjyec

Year of construction: 2016, condition: excellent (used), functionality: fully functional, Special equipment: automatic oil skimmer Technical data Heatable for aqueous cleaning agents. For the removal of oil and grease contamination in the shortest possible time. Universally applicable for the fully automatic cleaning of small parts from production, manufacturing, and maintenance, such as bolts, sleeves, and ball bearings. 2129905 Easy operation thanks to the fully automatic cleaning process. This allows skilled workers to concentrate on other important tasks. The washing tank is filled with a mixture of water and a water-soluble IBS special cleaner (washing solution). The contaminated parts to be cleaned are placed in the rotating washing basket, and the lid is closed. After setting the desired washing temperature and time, the device is switched on, and the solution in the tank is heated. In the closed device, the basket rotates around its own axis at a constant speed. The pump unit draws the washing solution from the washing tank and pumps it through 3 stainless steel nozzle tubes with overlapping flat jet nozzles. The parts to be cleaned are intensively blasted with the hot solution from all sides during the uniform rotation of the motor-driven basket. After the cleaning process is completed, the device switches off automatically. ∙∙ 1 pump arranged vertically ∙∙ 3 three-dimensional nozzle tubes made of stainless steel Njdpezwb Easfx Abyjdc ∙∙ robust stainless steel design ∙∙ additional small parts cleaning basket made of stainless steel (Ø 170 mm) ∙∙ rotating washing basket made of stainless steel, gear rim drive via separate motor ∙∙ intake filter in front of the pump shaft ∙∙ high spray pressure ∙∙ fume extraction ∙∙ stainless steel sieve plate with filter basket ∙∙ low water level protection W x D x H (closed): 1130 x 1010 x 1150 mm W x D x H (open): 1130 x 1220 x 1730 mm Usable height: 500 mm Load capacity: 150 kg Basket diameter: 780 mm Washing tank capacity: 85 liters Pump pressure: 3.1 bar Spray rate: 4800 L/h Power consumption: 4.8 kW / 400 V / 50 Hz Weight: 90 kg Temperature: 0-60°C

Condition: used, KB Prüftechnik Hardness Testing Machine, Type: KB 750 BVRZ Machine Type: KB 750 1 kg - 750 kg UNIVERSAL DIGITAL KB universal hardness testing machines for automatic and standard-compliant hardness testing. Suitable for all hardness testing methods in the load range HV 0.2 1 - 3000 kgf, Vickers, Brinell, Rockwell, Ndodezg Tyujpfx Abyec Super-Rockwell, Knoop (only HK 1), ball indentation hardness (plastics) and depth measurement according to Vickers and Brinell. Fully automatic testing sequence, evaluation of the indentations on the integrated LCD monitor using an integrated video camera and zoom lens guarantees the highest evaluation accuracy according to the standard. All hardness values are displayed digitally immediately. User-friendly and powerful control panel with a color LCD monitor, high contrast and glare-free. The measurement of the indentation is performed without parallax. The testing forces are electronically controlled and applied with the highest precision. The video image can optionally be output as a BMP file. All KB hardness testing machines are supplied with a basic equipment package that enables immediate operation with the ordered indenters. A selection of fixtures, testing tables, indenters, lenses, hardness comparison blocks, etc. is available. A connection to a PC or central computer is possible with all KB hardness testing machines. In conjunction with the fully automatic software and motorized cross table, the machine can be operated as a fully automatic system. fully automatic testing sequence optical evaluation via integrated video evaluation extremely user-friendly and powerful large LCD color display industrially designed foil keypad variable software adaptation Zoom lens 1:7 parallax-free measurement load cells, controlled load application, LED lighting Rockwell resolution 0.025 HRC extremely powerful 200 freely definable test programs Calibration machine accuracy (option) new LED ring light (option) automatic image evaluation (option) 2 interfaces parallel + serial, as well as keyboard connection extended load range XL (option) freely switchable language selection German, English, French, Italian KB750 BVRZ: Test load 3-750 kgf Brinell ISO 6506 HB depth measurement Vickers ISO 6507 HV depth measurement Rockwell ISO 6508 Rockwell ISO 6508 Superrockwell Testing table ∅80 mm Motor zoom 1:7 Lens 4x for HV10-HB5/750 NOT suitable for HV5 Operating function: Programmable digital panel with the following functions: Measurement of the hardness indentation on the LCD display, with adjustable measuring marks, without parallax Logically structured, simple operating guidance Any number of test programs can be created and stored (200) Automatic force selection by selecting the testing method Freely selectable application times of the testing forces Freely selectable dwell times of the testing forces Online help Automatic correction for curved surfaces according to DIN EN ISO Control of the fully automatic testing sequence Direct, digital hardness value display Tolerance display Conversions according to DIN 50150 Table B1 Protocol generation in DIN A4 format with standard printer via parallel interface Serial interface for data output to PC Optional network 4 languages: German-English-French-Italian Statistics functions, such as: Number of tests Min / Max Average Range Standard deviation cp / cpk Histogram (Changes and errors in the technical data are subject to change!)

Condition: new, Factory-new electrically heated stainless steel agitator tank EBB90RWP Including operating manual and CE declaration of conformity. The double jacket is filled with thermal oil, which is heated by an electric heating element. Alternatively available with other agitator types and in other sizes. Volume: 97L Nodoym Arbepfx Abyedc Dimensions approx.: Ø 540mm x cylindrical height 625mm Total height: 910mm (+ agitator motor) Material: 1.4301 stainless steel (V2A) Surface: inside and outside finely ground (matte finish) Weld seams ground smooth Max. operating temperature: 110°C Operating pressure (tank): Atm - Upright design on castors - Top: folding lid, half bolted, half hinged, with removable stainless steel grating for reach-in protection - Bottom: flat base with lateral outlet DN50 DIN11851 and disc valve - Agitator flange on the top cover - 2x push handles - 1x nameplate Propeller agitator Power: 0.25 kW Speed: 980 rpm Operating voltage: 3PH 400V

Condition: used, Ex-protected filter unit, extraction system, central extraction cartridge - impulse filter P. RIES GmbH Type 330 D ATEX Cartridge filter system, rectangular filter unit, central welding fume extraction Machine no. 10011932 Year of manufacture: 2020 - as new, unused Airflow rate: 3,300 m³/h Airflow rate: 0.9 m³/sec Filter area: 20 m² (1 piece cartridge filter) Differential pressure: 3,300 Pa (33 mbar) Extraction connection at filter inlet: 2x Ø 150 mm Exhaust connection at filter outlet: sound insulation hood Compressed air connection: approx. 8 bar Motor power: 3 kW Mains connection: 400 Volt, 50 Hz - Explosion-protected design ATEX II 2Db 125°C / 3G T4 - Pneumatic rotating filter cleaning, manual via push button - Manometer for differential pressure display (vacuum display in mbar) - Service door for filter replacement - Filter stage 1 = 1 cartridge filter Ø 325 mm, length 900 mm P-RIES, type cartridge filter 20.1 m², BGIA/IFA class M, antistatic - Filter stage 2 = filter outlet (sound insulation hood) equipped with 9 activated carbon filter cartridges, type AKZ 2500V, 266 m³/h per filter cartridge - Built-in radial fan, type IE 3-premium efficiency, 12% improved efficiency - Robust steel construction in RAL 7035 light grey, antistatic powder-coated - Dirt collection container as pull-out drawer approx. 70 litres (440 x 530 x 300 mm) - EC Declaration of Conformity, operating instructions with wiring diagram available Required space (L x W x H): 670 x 700 x 2430 mm Weight extraction unit: 211 kg Transport dimensions on pallet (L x W x H): 930 x 1350 x 1950 mm Ndodpfx Asy N Duqebysc Weight incl. transport pallet: 236 kg As new, unused, ex stock

Condition: new, Brand new stainless steel container Article number: 10846 Volume: 550 L Type: Standing on a plastic pallet Material (in contact with the media): Stainless steel V2A / AISI 304 Number of fixings: Plastic pallet Bottom: Dished bottom Max. operating pressure: Atmospheric Container dimensions: Inner diameter: 815mm Outer diameter: 890mm Total height: 1330mm Cylindrical height: 1070mm Total width: 890mm Materials: Inside: 14301 / AISI 304 Outside parts: 14301 / AISI 304 Facilities: Nameplate: no Outlet diameter: 50mm Nodsv Dunfepfx Abyedc Distance from drain to floor: 160mm

Condition: new, Year of construction: 2025, functionality: fully functional, shaft length: 1,064 mm, laser power: 30 W, type of cooling: air, overall weight: 35 kg, warranty duration: 12 months, scan area length: 220 mm, scan area width: 220 mm, Integra Fiber Laser – High-Precision Marking Laser for Series Production & Automation GLT – Grossmann Lasertechnik GmbH Made in Germany • Automated • Industry 4.0 Ready The Integra fiber laser is a fully integrated laser marking system designed for industrial series production, providing high cycle rates, precision, and process reliability. By combining fiber laser technology, integrated PLC, and modular machine architecture, the Integra is ideal for production lines, custom machinery, and automated marking stations. Technical Features • Power: 20 – 200 W • Galvo scan head with F-theta optics for maximum engraving speed Nsdpexvtu Dsfx Abyedc • Work area: 100×100 mm to 300×300 mm • Integrated PLC with TCP/IP communication and I/O interfaces • Compatible with LightBurn, EZCAD, or custom software • Optional: camera systems, pallet handling, conveyor belt integration • CE-certified, low-maintenance, suitable for continuous operation Advantages • Integration system “Made in Germany” – direct from the manufacturer • Custom machine building & automation according to customer requirements • Full integration into existing production environments • Highest marking quality on metal, stainless steel, aluminum, brass, plastic, and more • German support, online & on-site training, spare parts supply Typical Applications • Serial number and nameplate marking • Barcodes, QR codes, DataMatrix • Cable and connector identification • Tool and automotive industry • Electronics and plastics processing • Contract marking and custom machine engineering Delivery & Service • Delivery time: 3 – 6 weeks • Delivery, installation, and commissioning throughout Europe • Lifetime after-sales support including remote maintenance

Condition: new, functionality: fully functional, For sale is one (1x) safety door switch with latch, article number 570573. The item comes from warehouse/spare parts stock. The visual condition can be seen in the attached images. We will gladly provide further technical documentation or detailed images upon request. Ndedpfszxptuox Abyoc Inspection and collection are possible by arrangement. Shipping is possible for an additional fee. Subject to prior sale, errors and changes.

Condition: good (used), Year of construction: 2020, functionality: fully functional, total length: 9,000 mm, Adhesive application cell with ABB robot IRB 4600-60/2.05. Included in the adhesive application cell: Robot (weight 425 kg, payload 60 kg, year of manufacture 2020) 7th axis + steel structure (unlike in the images, the axis and steel structure have been extended to approximately 9 m) Adhesive application units Protective fences, etc. Not included: Roller shutter doors Ndedpfx Aozz Agmsbysc Fixturing device (available separately) Detailed drawings available upon request.

Condition: like new (used), functionality: fully functional, empty load weight: 900 kg, maximum load weight: 5,000 kg, overall weight: 6,000 kg, tire size: 300 x 80, tire condition: 100 %, trailer brake: trailer braked, Year of construction: 2025, Water tank trailer, 5000 liters - 25 km/h, with ABE (German type approval) Ndsdpfxozy Dy Ej Abyec Ideal for municipal services (gardening department), civil engineering, road construction for dust control, construction site supply, agriculture, or as a professional water tank for large companies – anywhere where water is needed on site. Equipped with a mounted wide-spreading nozzle and spray bar with nozzles. Coupling height approx. 700 mm. Automatic support wheel with folding mechanism. PTO pump for filling and emptying. Additional PTO pump for operating a high-pressure cleaner. As-new demonstration unit from 2025. Please send us your realistic offer. VAT can be shown separately.