Low loader trailer

LANGENDORF N&S FZ-Bau TLPL30 Tieflader Anh. hydr. Laderampe

Condition: used, overall weight: 40,000 kg, first registration: 04/2009, Schwarzmüller G404 Unladen weight: 8,580 kg Gross weight: 40,000 kg Ramps: mechanical Prjdpfsyrdhhex Ac Aeb Leaf suspension Errors and omissions excepted!

Condition: new, maximum load weight: 23,800 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete vehicle inventory with vehicles available for immediate and short-term delivery on our website. Excerpt from the equipment list. Complete equipment available upon request. Frame * Steel welded construction with front frame curve and rear bevel * Access ramp with excavator bucket recess in the center = recess in the rear between the longitudinal beams * Approximately 2,300 mm long Integrated into the outer frame * 5 pairs of approximately 4-tonne lashing points (4 x in the low bed and 1 x on the raised platform) * 7 pairs of recessed, pull-out approximately 10-tonne lashing rings (4 x in the low bed, 1 x in the access ramp, and 2 x on the raised platform) * Standard ball-bearing swivel frame attachments * Extendable widening elements on both sides of the low bed platform with softwood boards, approximately 50 mm thick * (The track width of the construction machinery to be transported must not exceed the outer frame width of approximately 2,550 mm) * 4 pairs of fold-up approximately 10-tonne lashing rings * Arrangement: 1 pair at the front on the raised platform, inside the longitudinal beams * 1 pair at the very back in the excavator bucket recess, left and right * 1 pair at the front on the raised platform, in front of the curve, inside the longitudinal beams * 1 pair in the low bed at the rear, in front of the access ramp, in the bucket recess on the left and right. Towing device Prjdpoz Ed Auefx Ac Aeb * Fixed drawbar with pivoting drawbar eye, approximately 40 + 50 mm, curved design, silent block mounting, drawbar retaining spring with tensioner * Truck coupling height from approximately 840 mm to approximately 1,030 mm PP004059B Drawbar length approximately 1,800 mm Support system * 2 automatic folding supports at the rear Axles * SAF air suspension low loader axles with drum brakes, load capacity 11 t/axle, S-cam brake approximately 300/200 mm, automatic brake linkage adjuster Wheels * 12 tires 235/75 R 17.5, 141J, manufacturer according to factory selection Braking system/Suspension * According to ECE regulation R13 * Dual-circuit compressed air braking system * Braking system manufacturer Wabco, EBS system 4S3M, 1st and 2nd axles monitored RSS/RSP * Stability program * Spring-loaded parking brake on 2nd and 3rd axles * Steel air tank * Brake/air connection lines with 2 single coupling heads, yellow/red EBS/ABS connection cable * Rubber band as a holder for EBS and electrical plugs * Air suspension with raising and lowering device (only on rear axles), automatic adjustment of the driving level from 15 km/h (RTR), with axle stop on the front axle Floor * Softwood floor, approximately 50 mm thick, impregnated, protruding approximately 5 - 10 mm above the frame Steel tear plate cover over wheels Ramps * 2 foldable, one-piece, lightweight steel access ramps * Length approximately 2,800 mm, width approximately 750 mm, with hardwood floor approximately 35 mm, impregnated * Ramps can be shifted in width from an intermediate distance of approximately 350 mm to a maximum overall width of approximately 3,000 mm * Ramps can be locked in the driving position by chains with tensioners * Ramp lifting aid with coil spring * Ramps can be shifted manually from the side with a rod * Square ribs welded on the outside on the ramps and rear access ramp Painting * Steel granulate cleaning * Hot-dip galvanizing * Multi-layer epoxy zinc phosphate primer and spray painting with 2-component polyurethane * Topcoat chassis = RAL 3002 carmine red *

Condition: new, maximum load weight: 30,160 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory with immediately and shortly available vehicles on our website. The following is an excerpt of the equipment. Complete equipment available upon request. Frame: Steel welded construction with a front frame bend, front corners chamfered and a chamfer at the rear. Access ramp with excavator bucket recess in the center = a recess at the rear between the longitudinal beams, approx. 2,300 mm long, integrated into the outer frame. - 4 pairs of approx. 4-tonne lashing points - 7 pairs of recessed, retractable approx. 10-tonne lashing rings (2 x on the raised platform, 1 x in the front bend slope, 3 x in the low bed between the wheel wells, and 1 x in the access ramp) - 2 pairs of wheel wells - 1 pair of wheel wells, approx. 2,300/1,270 x 400 mm (L1/L2 x W), in front of the bend, including a one-piece, drive-over aluminum cover, for a maximum surface load of approx. 11,650 daN/piece. - 1 pair of wheel wells, approx. 1,390/590 x 270 mm (L1/L2 x W), between the 3rd and 4th axles, including a one-piece, drive-over aluminum cover, suitable for the transport of wheel loaders with a wheelbase of approx. 2,700-3,600 mm, with wheel diameters of approx. 1,485-1,740 mm, maximum rear overhang of the wheel loader of 2,220 mm. - Width between the wheel wells approx. 1,255 mm (= outer/outer longitudinal beam) Frame attachments: - 5 pairs of mounting pockets in the outer frame for rectangular tube supports, approx. 100x50x5 mm (3 x in the low bed and 2 x on the raised platform). - Without rectangular tube supports. - On both sides of the low bed platform, retractable widening extensions with softwood planks approx. 50 mm (the track width of the construction machines to be transported must not exceed the outer frame width of approx. 2,550 mm). - 4 pairs of folding approx. 10-tonne lashing rings, arrangement: 1 pair at the front of the raised platform, inside the longitudinal beams; 1 pair at the very rear in the excavator bucket recess, left and right; 1 pair at the front of the raised platform, in front of the bend, inside the longitudinal beams; 1 pair in the low bed at the rear in front of the access ramp, in the excavator bucket recess, left and right. Towing device: - Fixed drawbar with approx. 50 mm heavy-duty towing eye, bent design, silent block bearing, drawbar locking spring with tensioner. - Truck coupling height from approx. 820 mm to approx. 1,010 mm. - Drawbar length approx. 1,800 mm. Support system: - 2 hydraulic supports at the rear, to be operated individually, control unit housed in a separate stainless steel box. Axles: - SAF air suspension low loader axles with drum brakes, load capacity approx. 11 tonnes/axle, S-cam brake approx. 300/200 mm, automatic brake linkage adjustment. Wheels: - 16 wheels, tires 245/70 R 17.5, 146/146F, manufacturer Conti HTR2 (tire load capacity approx. 12 tonnes/axle). Pedpfxoz Ed Azj Ac Aorb Braking system/suspension: - Braking system according to ECE regulation R13, two-line pneumatic braking system. - Braking system manufacturer Wabco EBS system 4S3M, 1st and 3rd axles sensed, RSS/RSP stability program, spring brake parking brake on 3rd and 4th axles. - Aluminum air reservoirs for a total weight of 44 tonnes. - Brake/air connection lines with 2 individual coupling heads, yellow/red. - EBS/ABS connection cable. - Rubber strap as a holder for EBS and electrical plugs. - Air suspension with lifting and lowering device, to be operated separately at the front and rear. - Automatic adjustmen