Copper cable granulation line

MG Recycling Matrix 400

Condition: excellent (used), Year of construction: 2023, operating hours: 1,500 h, functionality: fully functional, cutting force: 630 t, power: 90 kW (122.37 HP), empty load weight: 36,500 kg, total width: 2,400 mm, total length: 9,500 mm, overall weight: 40,000 kg, cutting length (max.): 1,600 mm, year of last overhaul: 2024, type of input current: three-phase, operating pressure: 220 bar, Scrap shear MS-6300e (scrap shear with electric motor) without operating materials. A 250kW diesel generator can be offered separately. Model: MS-6300e Cutting force: 630t Cutting length: 1600mm Discharge height: 500mm Power: 110 KW Capacity: 12-17 t/h Machine weight: 40 tons (+ diesel generator 4 tons) Hopper size: 3850mm x 2600mm x 1500mm Information: A scrap shear is used for economical scrap cutting: - simple automatic operation - Energy-saving - Cost-saving - No foundation required Function: Scrap is fed into the loading area with the aid of an excavator. Due to the horizontal filling area and the scrap's own weight, it falls down into the loading chamber and into the cutting area. The scrap is compacted at the front wall and cut by the horizontally moving tool pick-up side via the blades on the front wall. While the tool carrier carriage moves horizontally, the processed material is pushed out via the blades on the front wall of the container. When returning to the rear position, the loaded scrap moves into the interior of the shears under its own weight. The scrap shears are available in different versions depending on customer requirements and the output size can be selected (for new orders). Ksdpsuu Upgefx Aalsww Inspection and trial operation are possible.

Condition: used, Eldan Granulator HG129 Kodpfx Aot Uyvrjaljww

Condition: ready for operation (used), 🔧 Key Specifications Cutting System: Four-shaft configuration with two cutting shafts and two clearing shafts. Cutting Disc Diameter: Approximately 280 mm (11 inches). Cutting Unit Dimensions: Working width of 1,000 mm and length of 700 mm. Hopper Opening: Approximately 1,400 mm x 1,600 mm. Motor Power: Typically equipped with two 18.5 kW motors. Operating Speed: Low-speed operation at around 25 rpm for high torque and reduced noise levels. Kwjdpjwnx Uiefx Aaljw Weight: Approximately 2,500 kg

Condition: used, No. 10028 Cable granulation plant FRS BK 60 Used According to our customer, the machine is fully functional and can be inspected and tested on site Cable granulating system for up to approx. 1000 kg of cable per hour (according to our customer) Motor and blades were renewed in 2025 Rotor dimensions 610 x 500 mm 14 blades Motor power 45 kW Incl. magnetic conveyor belt Cylinder size 400 x 120 mm Motor power 1.5 kW Incl. sieve with two outlets Motor power 0.35 kW Installation dimensions approx. 7000 x 6000 mm LW Transport dimensions approx. 6000 x 2400 x 2600 mm LWH Weight approx. 6000 kg Sale on behalf of customer, ex location near 69123 Heidelberg, without dismantling, without transport and assembly Dismantling, transport and loading by us optionally possible Errors in the description and price reserved To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Kedpfx Aaoxwdndoleww Technical specifications, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or shipment Terms of delivery: ex location

Condition: new, Year of construction: 2025, A sand aggregate production plant is a facility where various types of aggregates (such as sand, gravel, crushed stone, or recycled concrete) are produced for use in construction and other applications. These plants typically include various stages of processing, from raw material extraction to the final product. Here are the key components and processes typically involved in a sand aggregate production plant: 1. Raw Material Extraction: - Quarrying or Mining: Aggregates are often extracted from quarries, mines, or riverbeds. Depending on the type of aggregate, the extraction process may involve drilling, blasting, or dredging. 2. Primary Crushing: - Jaw Crusher or Gyratory Crusher: The extracted raw material is usually transported to the plant and fed into a primary crusher, where large rocks are broken down into smaller pieces. Kedpfsq Ngb Dex Aaloww 3. Secondary Crushing: - Cone Crusher or Impact Crusher: The crushed material from the primary crusher may undergo further reduction in size through secondary crushing. 4. Screening: - Vibrating Screens: After crushing, the material is often screened to separate different sizes of aggregates. This process ensures that the final product meets the required specifications. 5. Washing: - Sand Washers: In some cases, especially for sand production, washing is done to remove impurities, clay, and fines from the aggregates, ensuring a cleaner and higher-quality product. 6. Grading and Sorting: - Classifiers or Graders: After washing and screening, the aggregates may go through additional processes to separate them based on size or quality. 7. Stockpiling: - Stockpiles: The final aggregates are usually stockpiled for storage before being transported to construction sites or other end-users. 8. Aggregate Storage and Handling: - Storage Bins or Silos: Larger production plants may have storage facilities, such as bins or silos, to store different types and sizes of aggregates before distribution. 9. Quality Control: - Laboratory Testing: Regular quality control testing is performed on aggregates to ensure they meet specifications for strength, size, gradation, and other properties. 10. Environmental Considerations: - Water Management: Some plants incorporate water management systems to recycle and reuse water used in the washing process, minimizing environmental impact. 11. Transportation: - Conveyors or Trucks: Aggregates are typically transported from the production plant to construction sites by conveyors, trucks, or other means.

Condition: excellent (used), functionality: fully functional, Year of construction: 2008, HESS RH 1500 2.1 SVA Year of manufacture: 2008 Start: 2009 Very good technical condition. Operating until the end of January. In 2022 a new roller for the upper hopper was installed by Topwerk - Hess. Vibrating table completely overhauled Siemens S7 control 3 molds included Kwedpfx Aaoyb Rvkslsw Price 195000euro Machine is located in Slovenia

Condition: reconditioned (used), Year of construction: 2000, operating hours: 32,169 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,320 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 22,000 kg, oil tank capacity: 900 l, For sale is a complete baling system consisting of conveyor technology, baling press (partially refurbished and tested) and wire stations. Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Typ HBC 60A Year of construction 2000 Hours of operation 32,169 hours, stand November 2024 Press power main press 60 tons Press power of pre-press max. 25 tons Feed channel 1,320 x 1,100 mm Theoretic cycle time 18 sec. Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical Throughput rate at a bulk weight of 30 kg/cbm approx. 5,5 tons/hour bulk weight of 50 kg/cbm approx. 10 tons/hour bulk weight of 100 kg/cbm approx. 16 tons/hour Bale weight 400 up to 750 kg, depends on material SPS controller Telemecanique TSX Micro Machine weight baler approx. 24 tons Scope of delivery: 1 piece chain belt conveyor 1 Bollegraaf HBC 60A baler with whirling unit 1 maintenance platform with access ladder 2 wire stations with deflection rollers for 10 wire reel stands (without wire) The following repair and overhaul work was carried out: Hydraulic oil tank emptied, cleaned and refilled with new oil Kjdpfxoviwdms Aaleww Oil filter and air filter replaced Hydraulic block partially resealed Hydraulic hose on hydraulic block replaced Wire entry marks on the floor passages welded shut and smoothed Tying unit cleaned, serviced Electrical system repaired, door flap contact switch partially replaced Whirbulator repaired General maintenance work carried out, lubricated Machine tested during operation, without the use of materials, in manual mode and in automatic mode, see function video Comments: The system has already been completely dismantled, stored and is available for loading at short notice. The documentation (BA, CE, electrical/hydraulic circuit diagram) is available. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: new, functionality: fully functional, Year of construction: 2025, A sand aggregate or gravel production plant is a facility where raw materials like sand, gravel, and other aggregates are processed to create various products used in construction and other industries. These facilities typically involve a series of processes to transform raw materials into the final products. Here is a general overview of the key components and processes involved in a sand aggregate or gravel production plant: 1. Mining and Extraction: - The process starts with the extraction of raw materials from quarries or mines. Heavy machinery such as excavators, loaders, and bulldozers are used to remove the raw materials from the earth. Kjdpfx Ajq Nia Ijaleww 2. Crushing and Screening: - The extracted raw materials often need to go through crushing and screening processes to reduce their size and separate them into different grades. - Crushers break down large rocks into smaller pieces, and screens sort the particles based on size. 3. Washing: - Washing is a common process to remove impurities such as clay, silt, and dust from the raw materials. This is particularly important for sand and gravel used in construction. 4. Grading and Sorting: - After washing, the materials may go through grading and sorting processes to separate them into different sizes and qualities. 5. Storage and Stockpiling: - Processed materials are often stored in stockpiles for further use. Adequate storage facilities are necessary to manage different grades of materials. 6. Conveying and Transportation: - Conveyor systems are used to transport materials between different stages of the production process. Transportation methods, such as trucks or conveyor belts, are used to move the final products to distribution points. 7. Quality Control: - Quality control measures are implemented to ensure that the final products meet the required specifications and standards. This may involve regular testing and analysis of the materials. 8. Environmental Considerations: - Sustainable practices and environmental considerations are crucial in the operation of a production plant. Measures such as dust control, water recycling, and rehabilitation of mined areas are often implemented to minimize the environmental impact. 9. Maintenance and Safety: - Regular maintenance of equipment is essential for the smooth operation of the plant. Safety measures are also critical to protect workers and ensure compliance with regulations. 10. Final Product: - The final products from a sand aggregate or gravel production plant may include various grades of sand, gravel, crushed stone, or other types of aggregates used in construction, concrete production, asphalt production, and other applications. It's important to note that the specific processes and equipment used in a production plant may vary based on the type of raw materials, the intended final products, and local regulations. Additionally, advancements in technology and sustainability practices may influence the design and operation of such facilities.

Year of construction: 2019, condition: used, For sale is a used cable granulation plant. Technical Data: Model: QJF-600 Voltage: 380V Frequency: 52.37 Hz Total Power: 53 kW Circuit Breaker: 125A Weight: approx. 3200 kg Dimensions: 3.5m x 2.0m x 2.8m Cable Diameter: 0.3–20 mm (dry cables only!) Capacity: 150–200 kg/h (cable/hour) Number of Blades: 10 rotating, 4 stationary Ksdpfx Aaew Sv Rzoleww Separator: L2.9 x W1.9 x H3.4 m Crusher: L1.97 x W1.4 x H1.95 m Output varies depending on the type of cable processed. This cable granulation plant is suitable for various types of copper cables with diameters up to 20mm. The cable shredder is straightforward to operate and very efficient. Up to 98.7% of the copper can be recovered from the cables. The machine price is €25,000 net, excluding shipping and installation. Transportation can be arranged upon request. Once you provide the postal code, we will calculate the delivery costs. Please note that transport costs must be added to the purchase price. Offer valid while stocks last. Subject to prior sale and errors! Installation and delivery available at additional cost!

Condition: new, Year of construction: 2024, functionality: fully functional, cutting force: 630 t, power: 110 kW (149.56 HP), total width: 2,400 mm, total length: 9,400 mm, total height: 3,800 mm, overall weight: 50,000 kg, cutting length (max.): 1,600 mm, type of input current: three-phase, Scrap Shear MS-6300mex (mobile version, with electrical motor) Diesel Generator 250KW is optional Modell: MS-63000e Cutting Power: 630t Blade length: 1600mm Output size: 500mm Power: 110 KW Capacity: 8-15 t/h Machine Weight: 39 t (+ Dieselgenerator 4t) Hooper size: 3900mm x 2400mm Information: Container Shear is used for economical scrap processing/ easy automatic operation/ energy saving/ cost saving/ no foundation needed. It can cut any kinds of scrap material. Different models for your choice. Machine is not suggested to cut high-carbon steel; axles; wire rope; pig iron; spring steel plate; rail; alloy steel; hub and so on... (these are not good for blades) Kedsr Ihzispfx Aaljww Function: Scrap is filled into the hopper by means of a grab loader. Due to the horizontal movement of the holder and the scrap’s dead weight, it falls to the bottom of the loading chamber and into the cutting space. After having been compressed on the front wall, the scrap is cut by the horizontally-moving tool-holding side via the blades on the front wall. While the tool-holding slide is moving horizontally, the processed material is pushed out via the blades on the container’s front wall. While returning to the rear position, the loaded scrap moves under its own weight into the shears’ interior. The scrap shear machines are available with different design, depending on the customer requirements. The output size can be choose (only for new order).