Second-hand machinery for sale (200,000)

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Bwjdpfxsh U Rzgo Afmow Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: used, 2 Ultra Low Profile Pallet Platform Lift Tables Model HY1501 1500 kg capacity Bwodeh Rkmwepfx Afmjw 240 Volt Platform 1600mm x 800mm Low profile 100mm from floor Safety bars Ramp included Electro hydraulic power pack Operator controller In excellent condition

Condition: good (used), functionality: fully functional, A good used Proface HMI Industrial PC - Model SP-5700TP fitted with SP-5B40 Open Box Module Ready to Ship Worldwide Bsdpfxjwmfbts Afmsww Please contact us via whats app for more pictures videos and chat

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, total length: 31,000 mm, total height: 4,000 mm, total width: 8,000 mm, workpiece weight (max.): 100 kg, input voltage: 230 V, workpiece height (max.): 1,500 mm, workpiece length (max.): 3,000 mm, fuel: electricity, sheet thickness steel (max.): 900 mm, We offer this ready-to-use GEMA powder equipment with single stage pre-treat systems and 2 x ovens, manufactured in 2012. Bwsdpfx Afs Agc D Somow Manufacturer: GEMA Construction year: 2012 Equipment type: Powder coating equipment Full working Compact Powder Coating Plant consists of below 1 x SINGLE STAGE PRE-TREAT PLANT 1 X DRY OFF OVEN 1 X GEMA QUICK COLOUR CHANGE POWDER BOOTH WITH RECIPROCATORS, CYCLONE AND AFTER FILTER 1 X OVERHEAD CONVEYOR SYSTEM 1 X TUNNEL OVEN If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: good (used), Year of construction: 2016, Experience seamless operation with all movements meticulously controlled by NC technology, ensuring swift and precise cuts every time. Boasting CNC controlled cutting height as standard, this machine provides unmatched versatility and precision in your cutting operations. Tailored for the demands of the roof truss and timber frame industries, this 3-axis CNC upstroke crosscut saw sets the standard for accuracy and reliability with a 700mm saw blade and 7.5hp motor. Whether you're tackling compound angle cutting or executing long scarf cuts, the HMZ-3 delivers flawless results with every cut due to its large cutting height of up to 250mm and capability to handle even the most intricate cutting tasks. An onboard optimisation package is included which allows cutting lists to be test optimised against timber lengths to generate a pre-optimised cutting list. Specification 6000mm infeed capacity Right-to-left feed orientation HM-Z saw unit with 700mm blade and centre-line cutting Bwodpfx Afo Agnz Nomow 4000mm outfeed table Onboard optimisation Outfeed monitor

Condition: used, Hurco TM6i, 2 Axis CNC Lathe, Year 2013, Tailstock, Collet Chuck, Swarf Conveyor, Air Bench Filtermist, Hydrafeed MSV 65 Bar Feed Unit, with 3 Jaw Chuck Hurco TM6i CNC turning centre with slant bed design. Compact and reliable CNC lathe suitable for precision machining, subcontract engineering and production work. The Hurco TM6i CNC Turning Centre is a compact slant bed CNC lathe designed for precision machining and efficient production of turned components. Suitable for subcontract engineering, toolroom and general manufacturing applications, the machine offers a practical solution for a wide range of turning requirements. Manufactured by Hurco, a respected builder of CNC machine tools, the TM6i is designed to provide reliable performance, machining accuracy and operator-friendly operation. Its rigid construction and compact footprint make it well suited to both production environments and smaller engineering workshops. Bsdpfe Aggphjx Afmoww The machine is capable of producing a wide variety of precision components and represents an excellent opportunity to acquire a quality CNC turning centre from a recognised manufacturer. Available for inspection at our Prestwick, Ayrshire facility. Specifications: Swing: 15.94" Machining Length: 13.4" Chuck Size: 6.65" Bar Capacity: 1.75" Power: 17.5 hp Max RPM: 6,000 RPM Turning Dia: 12.4"

Condition: used, Used Sterling Fluid Systems Liquid Ring Skid Mounted Compressor Skid: Comprises Sterling Fluid Systems Model KPHY 65112 1.4408 Stainless Steel Two Stage Liquid Ring Vacuum Compressor. Rated 265m3/h (154cfm) capacity with 1013mbar (14.7psi) input and 3.5bar (50.8psi) maximum over pressure. Direct driven by 36/40kW 400/690 volt 3/50 1484/1480 rpm motor rated EEX E II T3/T1&T3. Mounted on skid with Sterling 240 Litre Stainless Steel Vertical Receiver rated 4.5 bar maximum working pressure. Also includes (2) GSD Waermtechnik 4.9m2 Horizontal Stainless Steel Heat Exchangers rated 19kW capacity each. Tubes 12 litre capacity rated 4.5 bar design pressure at -20/+50 degC. Shell 42 litre capacity rated 4.5 bar design pressure at 90 degC. Bodpfxo Agv Tas Afmsww Specifications: Capacity: 156.1 ft³/min. Motor Power: 48.2 hp Material Of Construction: 1.4408 Stainless Steel Vacuum Rating: 1013 mbar input, 3.5 bar max overpressure Speed: 1484/1480 rpm

Condition: used, Unused GEA Niro type F01A stainless steel rotary atomiser suitable for use with GEA Niro Mobile Minor spray dryer. No atomiser wheel included. Bedj Agvz Nepfx Afmeww

Year of construction: 2007, condition: good (used), Used Bystronic Model VR – 3100mm x 6.5mm guillotine for sale Make: Bystronic Byshear Model: VR 6.5-31 Cutting capacity: 6.5mm Cutting length: 3100mm Rake angle 0.5-2.5 Back gauge range 1200mm Max Back gauge speed 180 mm/s Hydraulic Variable Rake Guillotine Shear. Including cnc control CYBELEC DNC 60 Programmable Back Gauge. Auto Blade Gap Adjustment. Front Supports & Squaring Arm. New/year 2007 Bystronic vr 6.5 x 3000 – 3metre x 6mm guillotine for sale Bsdpsq Dpuhsfx Afmsww

Year of construction: 2016, condition: excellent (used), Used modern, very clean & fully serviced RAS UpDownBend 78.40 cnc Folding System for sale 4metre up and down cnc folding machine with U shape back gauge as highlighted per photograph Year 2016 Bwedpfx Afennz Apemew Technical Data: Material Thickness max. (Mild Steel) 3.0mm Material Thickness max. (Stainless Steel) 2.0mm Material Thickness max. (Aluminium) 4.0mm Working Length 4060mm / 4metre Gauging Depth ("U" shape) 95-3270 (4150)mm Stop Finger Units (fix - telescope - fix) 2 + 10 + 2 Gauging System Accuracy -/+ 0.1mm Open Height Upper Beam max. 600mm Telescopic Gauging System (Travel Range) 640 – 1520mm Pivot Point Adjustment +/- 15mm Folding Beam Height Adjustment 150mm Folding Beam Travel Range 180 deg Working Height 1000mm Speeds: Upper Beam 75mm/s Folding Beam 110 deg/s Gauging System from min to max 2.2s

Year of construction: 2000, condition: good (used), Used Amada Tp150ex 150ton press / stamping machine Amada TP150 EX electric Power Press with feed Atkin Bhp feed and Atkin BHP decoiler New/year 2000 TP150 Model Amada TP-150EX Weight 16 tons Accessories Sick Guards Hydraulic Overload Variable Speed Drive Hydraulic Tool Clamping Capacity 15o tons Supplied New July 2000 Stroke 175mm Bed Area 1250 x 750 x 160mm Ram Area 700 x 550mm Ram Adjustment 100mm (motorised) Die Height 390mm Bwjdpfjn Smg Tsx Afmsw Ideal for automotive or aerospace sheet metal press work New c and h frame presses also available.

Condition: good (used), Year of construction: 2017, NNP Rotary moulder Bwodpfxsuanp Ne Afmow Stainless, belt dimensions 2250mm x 650mm, 650mm rotary moulder, previously used for pizza bases, with top mounted oil spray nozzle

Condition: excellent (used), functionality: fully functional, Year of construction: 2000, sheet thickness (max.): 13 mm, sheet thickness steel (max.): 13 mm, cutting length (max.): 3,100 mm, cutting width (max.): 3,100 mm, table length: 3,100 mm, table width: 3,100 mm, Used quality Edwards Pearson 3metre x 13mm hydraulic sheet metal guillotine Bwedeumlbwepfx Afmsw High Quality used Edwards Pearson VR 13/3000 Hydraulic Shear For Sale New / year 2000 Complete with front support arms and front operated back gauge / Cybelec DNC 10 control Rapid blade adjustment for thinner sheets Maximum material thickness 13mm x 3metre wide Fully serviced in good working condition Video Available upon request

Condition: excellent (used), Year of construction: 2014, 4 Qty Stainless Steel Hoppers 3 Qty Hoppers Dimensions 700mm x 1200mm x 1220mm H. 1 Qty Hopper dimensions 1200mm x 1200mm x 1220mm H Bwsdourf Twopfx Afmew With manual gate valve Gas strut opening lid Internal stainless mesh screen Mobile on lockable castors Some with pneumatic vibration device. Some with level sensor device In excellent condition

Condition: excellent (used), functionality: fully functional, Year of construction: 2002, working width: 3,000 mm, sheet thickness steel (max.): 6 mm, total width: 3,000 mm, cutting length (max.): 3,000 mm, table length: 3,000 mm, table width: 3,000 mm, Equipment: finger protection, lighting, safety light barrier, Used Edwards Pearson 3metre x 6.5mm hydraulic sheet metal guillotine for sale EDWARDS PEARSON Model VR – 3000mm x 6.5mm Guillotine (2002) Model: VR6.5/3070 Hydraulic Variable Rake Bwsdsuykdxopfx Afmjw Programmable Back Gauge Auto Blade Gap Adjustment Front Supports & Squaring Arm Popular CYBELEC DNC 60 control Year 2002 Delivery and installation with operator training can be included

Condition: excellent (used), Conveyor Food Grade 316 stainless steel Belt dimensions 1450mm x 700mm Bodpfx Ajyw Tdkefmoww Overall dimensions 1450mm long x 900mm wide

Condition: excellent (used), functionality: fully functional, Year of construction: 2016, control type: CNC control, controller manufacturer: Bystronic, controller model: Byvision, bending force (max.): 225 t, number of axes: 6, type of crowning: CNC-controlled, Equipment: CE marking, documentation/manual, emergency stop, european tool clamping system, foot remote control, lower tooling, safety light barrier, upper tooling, 1 Used High quality fully serviced Bystronic Xact Smart 225/4100 4metre x 225ton hydraulic downstroke cnc pressbrake for sale Bjdpfxjyxqzvj Afmoww Xact Smart 225/4100 Make: Bystronic Model: Xact Smart 225/4100 Year / new: 2016 Total axis: 6 – 4axis back gauge X R Z1 Z2 Hydraulic crowning Free standing no pit required Capacity / bed size / tonnage: 4metre x 4100mm x 225ton Cnc control: ByVision touch screen

Condition: used, 4m Length, 670 working height, 850 minimum stroke. 8 x Cramping bars at 500mm centres Bwsdpfxsymm Sfj Afmsw 3 x Hyrdaulic cylinders via motorised pump with starter Suitable for open plan and wedged stairs

Condition: used, Tote Bin Lifter for stainless steel meat bins Bsdpoym U Afefx Afmjww Lifting height: 2050 mm Total dimensions: 1050 mm x 900 mm x 2940 mm

Condition: used, Webomatic Mobile Double Chamber Vacuum Packer Type: CD 120-PR Serial number: 5710JL525 400 V, 3 Ph, 50 Hz, 5.0 A, 2.2 kW Bwsdpfoym U Injx Afmjw Seal length: (2x) 640 mm Dimensions chamber: (2x) 650 mm x 570 mm Busch vacuum pump Total dimensions: 1420 mm x 840 mm x 1060 mm.

Condition: excellent (used), functionality: fully functional, control type: CNC control, controller manufacturer: Delem, bending force (max.): 170 t, number of axes: 4, type of crowning: CNC-controlled, Equipment: CE marking, foot remote control, lower tooling, safety light barrier, upper tooling, Used Trumpf Trumabend V170 CNC Hydraulic Press Brake For Sale Subcategory: Press Brakes Tonnage: 170Ton Manufacturer: Trumpf Model: V170 Trumabend Condition: Used Trumabend DA65 2D CNC Controls 4 Axis machine, complete with i axis Bodpfx Afsx R Ul Ajmeww 2 Axis CNC Back Gauges R and X Axis complete with 4 fingers on the back stop CNC Ram Control Y1, Y2 CNC Bed Crowning Die Shift (iaxis) Pedestal Controls Electric Foot Switch Safety Light Guards

Condition: excellent (used), functionality: fully functional, Year of construction: 2016, pressing force: 40 t, table length: 1,030 mm, Equipment: CE marking, documentation/manual, safety light barrier, Used Bystronic Xpert 40ton x 1metre cnc pressbrake for sale Make: Bystronic Bwodpfoy D Smwex Afmow Model: Xpert 40/1030 Tonnage 400 kn / 40ton Back gauge: 6axis back gauge Bending length 1030 mm / 1metre Y-approach speed (up to) 300 mm/s Y-working speed (up to) 25 mm/s Accuracy Y-axis 0.004 mm Oil capacity 100 l Electric supply 7.5 kw Weight 4t Length, approx. [L] 1520 mm Width, approx. [W] 1584 mm Height, approx. [H] 2449 mm Xpert 40/1030 ByVision Bending control with 22 Inch Full HD display and touch technology

Condition: good (used), Horizontal PFM flow rapper is specifically designed to meet any need of flexible packaging for food and non-food applications. This is an ex bakery machine, in good working condition Bodpfjy D Uzqox Afmeww Price € 5,900

Condition: good (used), Burgess Three roll sheeter Stainless, three roll sheeter, with top mounted hopper, 450mm rollers, two fluted rollers and one smooth, on mobile frame, 3Ph Bodsy Ayckspfx Afmoww

Year of construction: 2018, condition: excellent (used), Winyard Midifill MKII Twin depositor Bodpfx Ajy H Hpxjfmjww 2018, stainless, 200Kg hopper, Previously used Deposit weight: 250g - 1000g of sourcrout and potato salad