Closed expansion tank

Bosch FT 10

Year of construction: 1997, condition: refurbished (used), 2 pieces volute casing pump in process design 1 piece completely overhauled, new ball bearings for pump and motor. Mechanical seal overhauled by specialist company. All seals new. Gbjdpfxsiuznus Afneh Flow rate: 6 m³/h Delivery head: 25 m Pump speed: 1440 1/min Shaft seal: double-acting mechanical seal Manufacturer: Burgmann HRZ 13754-00 SIC/SIC/-CAR/SIC-VITON Impeller type: closed two-channel impeller Impeller diameter: 277mm Bearing type: roller bearing Impeller side: 1x NU411 Drive side: 2x 7311 Lubrication type drive end oil Lubricant monitoring Oil level controller Materials: Pump housing: Duplex steel Noridur 1.4593 (9.4460) Wear plate: Duplex steel Noridur 1.4593 (9.4460) Pressure cover: Duplex steel Noridur 1.4593 (9.4460) Shaft: Heat-treated steel C45+N Impeller: Duplex steel Noridur 1.4593 (9.4460) Bearing bracket lantern: Cast iron EN-GJL-250 Shaft sleeve: Duplex steel 1.4462 Nominal size of suction nozzle: DN 80 Discharge connection Nominal diameter: DN 40 Nominal pressure suction PN 10 Nominal pressure pressure PN 10 Coupling manufacturer: Flender Coupling type: Eupex NH with intermediate sleeve Base plate: gray cast iron Motor manufacturer: AEG AM 132 Efficiency class: IE 0 Motor speed: 1476 1/min Frequency: 50 Hz Rated voltage: 400 V Rated motor power: P2 7.50 kW Thermal class: F Motor protection class: IP55 Cosphi: 0.82 Dimensions: Length: 1270 mm Width: 550 mm Height: 570 mm Weight: 300 kg The material 1.4593 Noridur is very well suited for - Chemical and process engineering industry - Sulphuric and phosphoric acid - Salt extraction and processing - Petrochemical industry - Coking plants - Textile and pulp industry - Food and sugar industry - Mining/coal mining and extraction - Flue gas desulphurization plants - Acidic, chloride-containing washing suspensions - Acidic process water - Waste water treatment/sewage treatment plants - Offshore and marine technology

Condition: excellent (used), Year of construction: 1996, pressure: 13 bar, operating pressure: 13 bar, 1 used steam boiler ----- Make: LOOS, Gunzenhausen Type: U-HD Heating surface approx.: 53 m² Output: 3,200 kg/h Max. operating pressure: 13.00 bar Increased test pressure: 24.05 bar Gedpfx Aov I Rpasfnjbh Water capacity at low water level approx.: 2,650 l Water capacity when full approx.: 3,770 l Year of construction: 1996 Equipped with a Weishaupt gas/oil combi burner, gas control system, control cabinet mounted on the boiler body, feedwater pump, and the existing coarse and fine valves.

Condition: good (used), Height: max 1,800 mm Pallet format: max 1,000 x 1,200 mm Speed: max 30 pallets/h Electrical system: 380 VAC Electrical system: 50 Hz Electrics: 3 PH Clamping force: max 5,500 N Equipment - Strapping machine: XP-112 MV - Sealing head CFH-1 Gbodpfx Aoqqkx Nofnsh - Stretch wrapper: GL-215 - Control system: S7

Condition: good (used), Year of construction: 2001, Manufacturer: KASTO Type: KASTOtec A4 Year of construction: 2001 Specifications: Metric Metric US Standard Sawing capacity round 90 430 Sawing capacity flat 90 430 x 430 mm Feed range 0 - 600 mm Multi-feed range 0 - 9999 mm Min, saw length 35 mm Max. Sawing speed 12 - 120 Saw blade dimensions 6830 x 41 x 1.3 mm Saw power 7.5 kW Gjdsu R R Avepfx Afnobh Dimensions (estimate) length 4800 mm width 2200 mm Height 2200 mm weight 5200 kg Please note: The information on this page is given in good faith and to the best of our knowledge, and where possible, has been obtained from the manufacturer, but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details.

Year of construction: 2004, condition: excellent (used), 1 used low pressure steam boiler ----- manufacturer : LOOS, Gunzenhausen type : U-ND capacity : 800 kg/h working pressure : 1 bar test pressure : 2 bar water contents full : 1.108 l year of construction : 2004 CE mark : 0036 equipped with Weishaupt gas burner G5/1-D, ZMD-LN, 200-900 kW, 120°C, fittings for gas supply, switch cabinet with touch panel, and the existing small and large-scale fittings. Dimensions of boiler body (approx.): diameter incl. insulation : 1.230 mm width : 1.450 mm transport height : 2.200 mm length : 1.950mm length including burner : 2.700 mm 1 used feedwater module ----- Gbedpfx Aonp Hwkefnsh manufacturer : LOOS, Gunzenhausen type : WSM content approx. : 800 l with switch cabinet, sampling water cooler, 2 dosing vessels

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Main press force 78 t Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Bale dimensions 1,100 x 750 mm Gjdpfevgrh Uox Afnobh Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: not inspected (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 750,750,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Specific press capacity: 5 kg/cm² Feed channel: 1.000 x 720mm (l x w) Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Gjdeic Rl Dopfx Afnobh Driving motor: 30 kW Bale weight: approx. 500 kg Machine weight: approx. 8t The hydraulic unit is functional, the drive motor is in the removed state.

Condition: excellent (used), Year of construction: 2005, 1 used steam boiler ----- - mounted on frame - Manufacturer: LOOS, Gunzenhausen Type: U-HD 800 Heating surface approx.: 14 m² Previously operated with: 640 kg/h Permissible operating pressure: 13 bar Increased test pressure: 24.05 bar Water content at normal level approx.: 748 l Total water content approx.: 1,108 l Year of manufacture: 2005 Gedpowwt D Defx Afnjbh CE marking: CE 0036 Equipped with Weishaupt combination burner gas & oil type GL3/1-E, ZMD, gas control section, control cabinet, feed water pump and existing coarse and fine fittings.

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, pressure: 1 bar, 1 used low-pressure steam boiler ----- Manufacturer: VIESSMANN Model: Vitoplex 100-LS Output: 580 kW Steam output approx.: 800 kg/h Water content approx.: 1,316 l Permissible operating overpressure: 1 bar Year of manufacture: 2001 Gbjdpsw I T E Isfx Afnoh CE marking: 0035 Equipped with Weishaupt gas burner, separate control cabinet, feed water pump, and the existing coarse and fine fittings.

Condition: refurbished (used), Year of construction: 1999, functionality: fully functional, pressing force: 71 t, filling opening width: 1,080 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, total width: 3,450 mm, total height: 4,090 mm, total length: 10,020 mm, input voltage: 400 V, overall weight: 27,000 kg, noise level: 85 dB, pressure: 300 bar, transport height: 2,300 mm, power: 37 kW (50.31 HP), Fully automatic channel baler with pre-press flap available immediately. The machine includes a conveyor belt with a floor-mounted section. The baler is supplied in refurbished condition and the conveyor belt underwent a belt overhaul at the beginning of this year. The machine was taken out of production at the beginning of October and is currently stored in our facility. It can be demonstrated in operation at our location. This machine is particularly suitable for baling paper/cardboard and various types of plastics such as PET, HDPE, and big bags. Technical specifications baler: Drive: 37 kW Press force: 71 tons Bale dimensions: 1100 x 720 x 1300 mm (length adjustable) Number of wires: 4 vertical Filling hopper dimensions: 1620 x 1080 mm Bale weight: up to 600 kg (depending on material) Capacity: up to 20 tons per hour (depending on material) Transport weight: 27,000 kg Gbedpfxsxl Rqbo Afnoh Technical specifications conveyor belt: Length of horizontal section: 3,000 mm Length of inclined section: 7,424 mm Angle: 29° Filling option: at floor level